User’s Manual WMP-G09
FCC Statement : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11b/g Mini-PCI Card. This Mini-PCI Card is based on Atheros AR5005GS chipset that complied with IEEE 802.11b standard from 2.4~2.5GHz, and it can be used to provide up to 11Mbps for IEEE 802.11b and 54Mbps/108Mbps for 2.4GHz IEEE 802.11g to connect your wireless LAN. With seamless roaming, fully interoperability and advanced security with WEP standard, 802.
2.0 Requirements The following sections identify the detailed requirements of the 802.11g Mini-PCI Card. 2.1 Functional Block Diagram UFL Connectors Mini-PCI PC Atheros AR2414 802.
2.2 General Requirements 2.2.1 IEEE 802.11b Section # Feature Detailed Description 2.2.1.1 2.2.1.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers Ÿ Ÿ IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK Ÿ 2400 ~ 2497MHz ISM band Ÿ Data Rate Media Access Protocol Transmitter Output Power Receiver Sensitivity Ÿ Ÿ 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 11, 5.5, 2, and 1Mbps CSMA/CA with ACK Ÿ Typical 18dBm at 11, 5.
# Feature Detailed Description Sensitivity Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ PDUs) Error Rate = 10% – 87dBm at 6Mbps – 86dBm at 9Mbps – 85dBm at 12Mbps – 83dBm at 18Mbps – 80dBm at 24Mbps – 76dBm at 36Mbps – 71dBm at 48Mbps – 66dBm at 54Mbps 2.2.3 General Section # Feature Detailed Description 2.2.3.1 Antenna Connector Operating Voltage Current Consumption Ÿ Dual UFL antenna connectors Ÿ 3.
2.3 Software Requirements The Configuration Software supports Microsoft Windows 98SE, ME, 2000, and XP. This configuration software includes the following functions: Ÿ Information Information allows you to monitor network status. Ÿ Configuration Configuration allows you to configure parameters for wireless networking. Ÿ Security Supports enhanced security WEP, 802.1x,WPA. 2.3.1 Information # Detailed Description 2.3.1.1 Feature General Information 2.3.1.2 Current Link Information Ÿ 2.3.1.
# Detailed Description 2.3.2.3 Feature Power Save 2.3.2.4 RTS Threshold Ÿ 2.3.2.5 Fragment Threshold Transmission Speed Ÿ Roaming Ÿ 2.3.2.6 2.3.2.7 Ÿ Ÿ Extend the battery life of clients by allowing the client to sleep for short periods of time while the Access Point buffers the messages. Set the number of bytes used for fragmentation boundary for messages Set the number of bytes used for RTS/CTS boundary This indicates the communication rates.
# Feature 2.5.3 Physical Layer and Functionality Detailed Description Ÿ requirements Meet ALPHA Engineering Test Plan and Test Report 2.6 Requirements of Reliability, Maintainability and Quality # Feature Detailed Description 2.6.1 2.6.2 MTBF Maintainability Ÿ Ÿ 2.6.3 Quality Ÿ Mean Time Between Failure > 30,000 hours There is no scheduled preventive maintenance required The product quality is followed-up by ALPHA factory quality control system 2.
l Test Program Operation Guide: [Step1] Run program in Desktop at server (see Figure 1) to open test window (see Figure 2). (Figure 1) (Figure 2) [Step 2] (a) Select Golden Card Type as you need (WCBG09..A1), then click ”Golden Start” button (Figure 3). (b) Figure 3 pops up. The emersion of DOS window means Golden Unit is functioning well.
[Step 3] Select ”DUT PC” (Figure 5) and press ”ENTER” button to show the test (Figure 6) (Figure 5) (Figure 6)
[Step 4] press “setting ”and then show form Figure 7,enter Password “abcdef” will show Figure 8, press “確 定 ” button. (Figure 7) (Figure 8) [Step 5] chose “setting->DUT setting”, will show Figure 9,and chose and set the test item and equipment.
(Figure 10) [Step 6] Scan the serial number on PCBA. [Step 7] Start the test by clicking “DUT Auto Test” button (see Figure 11). (Figure 11) Remark: Item 2 & 3 are for the Target Power Test, items 5 are for SpecMask Test and item 6 is for TX and RX Link Test.
