802.11g Wireless Music Bridge Model # AWMB100 User’s Manual Ver.
Table of Contents 1 Introduction ................................................................................................................ 1 1.1 FEATURES................................................................................................................ 1 2 Quick Start Guide ....................................................................................................... 2 2.1 HARDWARE INSTALLATION .....................................................................................
1 Introduction The AirLink101 Music Bridge is a network audio device and wireless Access Point. It allows you to stream all of your audio content from your PC to speakers in your living room or bedroom, in the glory of 5.1 surround sound. At the same time, AirLink101 Music Bridge can be used as a wireless router to make your existing internet connection accessible around your home.
2 Quick Start Guide 2.1 Hardware Installation Step 1 Connect the power adapter to the back of the music bridge and connect the other end to a power outlet. Step 2 Connect one end of a networking cable to the computer you plan to use with the music bridge, then connect the other end to the Ethernet port on the back of the music bridge. The following is a description of the different audio outputs on the Music Bridge.
Green – Headphones/Stereo/Front Surround – Plug in your stereo speakers or headphones here. If you are setting up surround sound, use this connection for your front surround speakers. Orange – Center channel/Subwoofer – This connection is used for surround sound. Connect your center channel and subwoofer to this output. Black – Rear Surround – This connection is used for surround sound. Connect your rear surround speakers to this connection.
Note: If the autorun window does not appear automatically, go to Start -> Run and type D:\Utility\Setup.exe (where D is the letter of your CD-ROM drive) and click OK. Step 2 Click Next at the welcome screen. Step 3 Click Install at the installation screen. Step 4 The setup wizard will automatically appear. Click on the Click Here to Start.
2.3 Configuring the Music Bridge Step 1 A list will appear showing your Music Bridge. Select it from the list and click Next. If nothing appears on the list, make sure that the music bridge is connected to your computer and properly powered on. Also make sure that you disable any software firewalls you have installed on your computer. Step 2 The default username for the music bridge is admin and the default password is admin. Enter this into the appropriate boxes and click Next.
Step 3 This screen allows you to change the device name, username, and password. If you want to change any of this information, enter it into the boxes and click Next. You can also leave the default settings and click Next. Step 4 If you are not using the wireless function of the music bridge click on I only have a wired network and the configuration is complete. You can now connect the music bridge to your router and start playing music. If you plan to use the music bridge wirelessly, go to Step 5.
Step 5 Select your network from the list and click connect. Step 6 If your network is encrypted, enter the encryption information at the next screen and click Next.
Step 7 The setup is complete. Click on Finish to save the settings. Step 8 You can now disconnect the music bridge from your computer and place it where you would like to use it.
2.4 Connecting to the Music Bridge Step 1 Double click on the Wireless Audio Center icon in the system tray. Step 2 Click the Scan Audio Device button. The software will search for and find all Music Bridges on the network. Step 3 Select the music bridge you wish to use from the list and click the Connect button.
Step 4 Choose the appropriate Playback Buffer Mode for the type of audio you are playing and click Confirm. You can now play audio on your computer and it will be sent to the music bridge.
3 Using the Wireless Audio Center Double-click on the system tray icon on the bottom-right hand corner of your desktop. The Wireless Audio Center will appear for you to configure. 3.1 Audio Link Tab The Audio Link Tab is where you go to connect to your AirLink101 Music Bridge and customize your audio buffer settings (see Playback Buffer Mode below for an explanation). You can also access the Setup Wizard to easily make networking changes to the Music Bridge.
Click to open the Setup Wizard. Click to save the current settings from this screen. Click to exit this screen. Playback Buffer Mode Buffer Status Select the length of your audio buffer. A larger audio buffer prevents your signal from “breaking up” when there is lots of traffic on your network. However, it also adds delay between when you perform an action (like playing a song) and when you hear sound.
Analog Output Here you select what type of system you have hooked up to the AirLink101 Music Bridge. For example, if you’re using headphones, click on icon. Click on the icon if you’re the using a 6-channel (or 5.1) speaker system. S/PDIF Output You can choose either Dolby Digital Live or Digital Audio 48kHz to be output from the digital output jack. Dolby Digital Live: This mode allows you to send 5.1 channel audio data over a single wire.
3.3 Mixer The Mixer allows you to control your volume levels. Volume Control Adjust this knob using your mouse to change the overall volume level. Wave, SW Synth, If you want to change the volume for a specific audio source, you can make separate adjustments to each of these sliders. CD player Click to exit this screen. 3.4 Effect The Effects page lets you spice up your audio by providing a 10-band EQ and environment (reverb) processing.
Environment Select the environment you wish to emulate: Bathroom : Concert Hall : Underwater : Music Pub For additional choices, click the More Options button and choose one from the pull-down menu. Environment Size Click to adjust the size of the virtual environment. Equalizer There are 12 equalizer presets to choose from, many optimized for different styles of music, such as Rock, Jazz, Rap, etc.. User Defined You can change the gain settings for each frequency band and save it as your own preset.
“-” to delete current the current user preset. Click to exit this screen. 3.5 Karaoke The Karaoke feature allows you to both adjust pitch up/down and remove vocals from regular music tracks. Click ON to enable the karaoke menu. Use the check boxes next to each feature to adjust them. The reset button will return all settings to their default configuration. 3.6 FlexBass FlexBass is a software crossover that you can use to reduce/increase bass coming through specific speakers.
3.7 Information This tab displays information about your current 3D audio engine, sound chip, Network audio driver and DirectX version. You can also decide if the audio configuration icon should be shown in the system tray.
18
4 Wireless Modes of operation Besides streaming audio around your home, the Music Bridge can be used as a wireless access point. You can also use the Music Bridge as an Ethernet bridge and connect a computer to the Ethernet port for wireless access to your router. By default, the AirLink101 Music Bridge is configured as an Access Point. To change your networking settings quickly and easily, you can go to the Wireless Audio Center and run the Setup Wizard.
20
5 Advanced Network Configuration Advanced networking options can be configured through the Web Utility. This utility can be accessed in two ways: 1. Open the Wireless Audio Center and click on the hammer icon under the Status bar (see right). 2. The second way is to open your web browser and type in the IP address that the AirLink101 Music Bridge has been assigned. If you don’t know what this address is, If you cannot access the web utility: 1.
Step 2 You may change the default settings of the IP Address and Subnet Mask, then click Next to continue. Step 3 Configure the following wireless networking settings and then click Next to continue. Step 4 Select the wireless encryption type from the pull-down menu and click Finish to complete the setup wizard. WPA2 encryption is recommended for the highest level of security, but not all networking equipment is compatible with it.
5.2 Status In this screen, you can see the current settings and status of your AirLink101 Music Bridge device. System Uptime Firmware Version The duration of time the AirLink101 Music Bridge has been servicing the network.
AirLink101 Music Bridge device. Wireless Configuration Mode There are two modes supported: Access Point and Client Band Shows the wireless band that is being used. SSID The SSID differentiates wireless networks from each other. Therefore, all access points and devices attempting to connect to a network must use the same SSID. It is case-sensitive and must not exceed 32 characters. A device will not be permitted to join the network unless it can provide the unique SSID.
5.3 Wireless 5.3.1 Basic Settings This page includes all major networking parameters. Any parameter changes require the device to reboot for the new settings to take effect. Disable Wireless LAN Interface Band Check this box to disable the Wireless LAN Interface. By doing this, you won’t be able to make wireless connections with this Access Point on its network. In other words, this device will not be visible by any wireless stations. You can choose one of the following modes: 2.4GHz (B): 802.
Network Type SSID Channel Number Associated Clients Apply Changes Reset and Client. When in Client mode, you can select between Ad-Hoc and Infrastructure types. The SSID differentiates wireless networks from each other. Therefore, all access points and devices attempting to connect to a network must use the same SSID. It is case-sensitive and must not exceed 32 characters. A device will not be permitted to join the network unless it can provide the unique SSID.
Authentication Type To provide a certain level of security, the IEEE 802.11 standard has defined two types of authentication methods, Open System and Shared Key. With Open System authentication, a wireless PC can join any network and receive messages that are not encrypted. With Shared Key authentication, only those PCs that possess the correct authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an Open System network.
the Authentication mode automatically. Fragment Threshold Fragmentation is used for improving efficiency when there is a lot of network traffic. If your 802.11g Wireless Adapter often transmits large files into the wireless network, you can enter a new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS Threshold RTS Threshold is implemented to prevent the “Hidden Node” problem.
instead of providing a remedy. Beacon Interval Data Rate Preamble Type Broadcast SSID IAPP 802.11g Protection *This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Beacon Interval is the amount of time between beacon transmissions.
the network’s performance. Apply Change Reset Click this button to save your settings. Click to discard the settings you have entered. 5.3.3 Security Here you can configure the security of your wireless network. If you are using the AirLink101 Music Bridge on an existing network, you will probably have a security scheme already set up, which you should follow here. If you are setting up a new network, you can configure the security however you like.
Authentication to have a RADIUS server issue the WEP key dynamically. For most home users, you will have to enter the WEP key manually on each device that joins the network Set WEP key Clicking the Set WEP Keys button will prompt you with a new window. Here, select a 128-bit key for higher security. Select HEX if you are using hexadecimal numbers (0-9, or A-F). Select ASCII if you are using ASCII characters (case-sensitive).
Pre-shared Key The pre-shared-key serves as a password for the network. Enter an 8-63 letter password, and ensure that the same password is used on all other clients on the network. There are two formats for setting the Preshared key, Passphrase and Hex. If Hex is selected, users will have to enter a 64-letter key. For easier configuration, the Passphrase (at least 8 characters) format is recommended.
Wireless Access Control Mode MAC Address Comment Apply Changes Reset Current Access Control List Delete Selected Delete All Reset Select the Access Control Mode from the pull-down menu. Disable: Select to disable Wireless Access Control Mode. Allow Listed: Only the stations shown in the table can associate with the AP. Deny Listed: Stations shown in the table won’t be able to associate with the AP. Enter the MAC Address of a station that is allowed to access this Access Point.
5.3.5 Site Survey Site survey displays all the active networks in range of your device. When you are in client mode, you can also select an Access Point to associate with. Click Refresh to get the latest information. 5.4 TCP/IP On this page, you can change the TCP/IP settings of your AirLink101 Music Bridge device, enable or disable the DHCP Client and 802.1d Spanning Tree, and clone MAC Addresses.
IP Address, Subnet These fields can only be modified when DHCP Mask, Default Client mode is disabled. If you are connecting Gateway to an existing network and are unsure what to enter here, ask the person that set up your network to provide these values for you. DHCP DHCP can be used to automatically configure your network addresses. Select Disable, Client or Server from the pull-down menu. Disable: Don’t use DHCP Client: Automatically obtain a network address.
5.5.2 Statistics The Statistics table shows the packets sent and received over wireless and ethernet LANs.
5.5.3 Upgrade Firmware 1. Download the latest firmware from your distributor and save the file on your hard drive. 2. Start the browser, open the configuration page, click on Other, and click Upgrade Firmware to enter the Upgrade Firmware window. Enter the new firmware’s path and file name (i.e. C:\FIRMWARE\firmware.bin). Or, click the Browse button, find and open the firmware file. 3. Click Reset to clear all the settings on this page. Or click Upload to start the upgrade. 5.5.
When prompted, select “Save this file to disk”, and enter the file name and the file location. Load Settings From File: Click Browse… if you want to load a pre-saved file, enter the file name with the correct path and then click on Upload. Or click Browse… to select the file. 5.5.5 Password For security reasons, it is recommended that you create a password-protected user account to access the web utility of this Access Point. Leaving the user name and password blank will disable this protection.
Click Apply Change to logout of the web configuration page.
Appendix - Specifications Standards • IEEE 802.11g/b Power • External Adapter: DC 5V/2A Frequency Range • 2.412 ~ 2.497GHz OS Supported • Windows Vista / XP / 2000 Antenna • Single attached 2 dBi dipole antenna Package Contents • 802.
This equipment also should be installed and operated with minimum distance 20cm between the radiator & your body.
Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Web site: www.airlink101.com *Theoretical maximum wireless signal rate based on IEEE standard 802.11g specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, mix of wireless products used, radio frequency interference (e.g.
