User Manual For Wireless Mini PCI Adapter (Atheros AR9223) Model Number : WMP-N09H Revision: 1.3 This document contains confidential proprietary information and is the property of Alpha Networks Inc.. The contents of this document may not be disclosed to unauthorized persons without the written consent of Alpha Networks Inc..
Operation Manual Test Utility Installation: 1. Unzip “ ART_v0_7_b27_ar928xALL 2. The utility must run on WinXP or Vista Hardware Installation: Before insert the card, please execute the below instruction at first!! 1. WinXP OS: Enter in the directory: C:\ v0_7_b27_ar928xALL \art_driver\bin\xp Execute the uninst_old_drv.bat: Execute the inst_new_drv_xp.bat Vista OS: Enter in the directory: C:\ v0_7_b27_ar928xALL \art_driver\bin\Vista Execute the uninst_old_drv.bat: Execute the inst_new_drv_xp.bat 2.
For example: press “h” to choice single chain or both chains in test mode.
2. Continuous Transmit Options: a. Before the continuous Transmit test, need to press “e” first The command will load the calibrate data to the EPROM, and then the card can transmit the target power. b. The channel frequency, data rate and output power could be changed in continuous transmit options. Press “c” to increase the output power, 11g Power ( data rate 6Mbps ) is 18dBm, 11b Power is 17dBm, press ESC to return to the main Test Options menu when finished. 3.
1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11n Draft 2.0 Mini PCI. This mPCI is based on Atheros chip that complied with IEEE 802.11n Draft 2.0 from 2.4~2.5GHz, and it is also backward compatible to comply with IEEE 802.11g and IEEE 802.11b standard to connect your exist 802.11 b/g wireless LAN device. 1.2 Product Features Compatible with IEEE 802.11g high rate standard to provide wireless 54Mbps data rate Compatible with IEEE 802.
2.2 General Requirements 2.2.1 IEEE 802.11b Section # Feature 2.2.1.1 2.2.1.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers 2.2.1.3 2.2.1.4 2.2.1.5 2.2.1.6 2.2.1.7 2.2.1.8 Detailed Description Data Rate Media Access Protocol Transmitter Output Power Receiver Sensitivity IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK 2400 ~ 2483.5MHz ISM band 11 channels for United States/ Canada/ Taiwan 13 channels for Europe Countries 14 channels for Japan 11, 5.
# Feature 2.2.3.4 Channel Numbers 2.2.3.5 2.2.3.6 Data Rate Media Access Protocol Transmitter Output Power Receiver Sensitivity 2.2.3.7 2.2.3.8 Detailed Description 11 channels for United States/ Canada/ Taiwan 13 channels for Europe Countries 13 channels for Japan From MCS – 0 to MCS –15 as shown in Appendix I CSMA/CA with ACK draft 802.11n (20MHz): 577.4mW draft 802.11n (40MHz): 328.
2.3 Software Requirements The Configuration Software supports Linux driver. This configuration software includes the following functions: Information Information allows you to monitor network status. Configuration Configuration allows you to configure parameters for wireless networking. Security Supports enhanced security WEP, 802.1x, WPA and WPA2. 2.3.1 Security # Feature Detailed Description 2.3.1.1 Encryption 2.3.1.2 WEP Management 2.3.1.3 2.3.1.4 802.
# Feature 2.7.2 Non-Operating Temperature Conditions 2.7.3 Operating Humidity conditions Non-Operating Humidity Conditions 2.7.4 Detailed Description Neither subassemblies is damaged nor the operational performance is degraded when restored to the operating temperature after exposing to storage temperature in the range of –20 ℃ to +75 ℃. The product is capable of continuous reliable operation when subjected to relative humidity in the range of 10% and 90% non-condensing.
Appendix I: Rate Dependent Parameters for High Throughput .
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: RRKWMPN09H”.
The final end product must be labeled in a visible area with the following: “Contains TX IC : 4833A-WMPN09”. Manual Information That Must be Included The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove. This RF module in the user’s manual of the end product which integrates this module.
以下警語適用台灣地區： 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即 停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通 信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 本模組於取得認證後將依規定於模組本體標示審合格籤，並要求平台上標示「本產品內含 射頻模組：ID 編號」 Alpha Networks Proprietary and Confidential Information 15
