User Manual For WMP-N09H 無線網路卡 Wireless Mini PCI Adapter
Version: 1.1 2011/1/13 This document contains confidential proprietary information and is the property of Alpha Networks Corporation. The contents of this document may not be disclosed to unauthorized persons without the written consent of Alpha Networks Corporation.
Contents TEST OPERATION MANUAL............................................................................................................4 Test Utility Installation:....................................................................................................................4 Configuration: ..................................................................................................................................5 1.0 SCOPE........................................................................
Test Operation Manual Test Utility Installation: 1. Unzip “ART_V0_5_b25ALL.zip” to “C:\”. 2. The utility must run on Win2000 or WinXP. Hardware Installation: Before insert the card, please execute the below instruction at first !! 1. Win2000 OS : Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\2000 Execute the uninst_new_drv_2k.bat: Execute the inst_new_drv_2k.bat : WinXP OS : Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\xp Execute the uninst_new_drv_xp.bat: Execute the inst_new_drv_xp.
Configuration: 1. Enter the DOS command mode , then change the directory to : C:\ v0_5_b25ALL\art_driver\bin\xp 2. Input the instruction: art \id=2082 Then press enter . ART TEST MODE: 1. Once utility is executed, a menu with test options will appear. To run a test, press the character key that is assigned to the test option. For example, press “c” to run the continuous transmit test, or press “r ” to run the continuous receive test.
finished. 1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11n Mini PCI. This mPCI is based on Atheros chip that complied with IEEE 802.11n from 2.4~2.5GHz, and it is also backward compatible to comply with IEEE 802.11g and IEEE 802.11b standard to connect your exist 802.11 b/g wireless LAN device. 1.2 Product Features Compatible with IEEE 802.11g high rate standard to provide wireless 54Mbps data rate Compatible with IEEE 802.
2.1 General Requirements 2.1.1 General Section # Feature 2.1.1.1 2.1.1.2 Antenna Type Operating Voltage Form Factor and Interface 2.1.14 Detailed Description Two UFL antenna connectorss 3.3VDC +/- 10% Mini-PCI type III A form factor 2.2 Requirements of Reliability, Maintainability and Quality # Feature 2.2.1 2.22 2.2.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co‐location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re‐evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 3.1dBi (Peak Gain) Antenna having a higher gain is strictly prohibited per regulations of Industry Canada.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.
