Manual For 11n Wireless LAN CARD 11N 無線網卡 Model Number : WMP-ND02 Alpha Networks Proprietary and Confidential Information 1
1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11n Draft 2.0 Mini PCI. This mPCI is based on Ralink chipset that complied with complied with IEEE 802.11n Draft 2.0, and it is also backward complied with IEEE 802.11a standard from 5.15~5.850GHz(upon every contries to use different frequencies) wideband and IEEE 802.11b/g standard from 2.4-2.4835GHz. It can be used to provide up to 54Mbps for IEEE 802.11a and IEEE 802.11g , 11Mbps for IEEE 802.
2.0 Requirements The following sections identify the detailed requirements of the 802.11n Draft 2.0 mPCI. 2.1 Functional Block Diagram 2.2 General Requirements 2.2.1 IEEE 802.11a Section # Feature Detailed Description 2.2.1.1 2.2.1.2 Standard Radio and Modulation Type Operating Frequency Ÿ Ÿ IEEE 802.11a BPSK, QPSK, 16QAM, 64QAM with OFDM Ÿ 5.15 ~ 5.25GHz. , 5.725~5.850 GHz for US and Canada 5.25 ~ 5.35GHz. , 5.725~5.850 GHz for Taiwan 5.15 ~ 5.35GHz and 5.47~5.725GHz for Japan 5.15 ~ 5.
# Feature Detailed Description 2.2.1.6 Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector Ÿ CSMA/CA with ACK Ÿ Maximum to 23.15dBm # Feature Detailed Description 2.2.2.1 2.2.2.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers Ÿ Ÿ IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK Ÿ 2400 ~ 2483.
# Feature Detailed Description Numbers Data Rate Media Access Protocol Transmitter Output Power Receiver Sensitivity Ÿ Ÿ 13 channels for Europe Countries 13 channels for Japan 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK Ÿ Maximum to 24.81dBm # Feature Detailed Description 2.2.4.1 2.2.4.2 Standard Radio and Modulation Type Operating Frequency Ÿ Ÿ IEEE 802.11n BPSK, QPSK, 16QAM, 64QAM with OFDM Ÿ 2.4 ~ 2.4835GHz, 5.15 ~ 5.25GHz. , 5.725~5.850 GHz for US and Canada 2.4 ~ 2.4835GHz, 5.25 ~ 5.
# Feature 2.2.4.7 2.2.4.8 Detailed Description Protocol Transmitter Output Power Receiver Sensitivity Ÿ Maximum to 27.4dBm Ÿ Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = 10% at room Temp. 25degree C and 3.
# Feature 2.4.1.2 Current Link Information Ÿ 2.4.1.3 Site survey Ÿ # Feature Detailed Description 2.4.2.1 ESS ID Ÿ Network Type Ÿ Ÿ 2.4.2.2 Detailed Description Ÿ Utility Version. Current Link Information shows the Current Setting ESSID, Channel Number, Associated BSSID, Network Type, Security Status, Link Status, Transmit Speed, Signal Strength, and Link Quality. To search the neighboring access points and display the information of all access points. 2.4.
2.5 Mechanical Requirements # Feature Detailed Description 2.5.1 2.5.2 2.5.3 Length Ÿ Ÿ Ÿ Width Height 57.64mm(max) 59.60mm(+-0.25) 6mm(+-0.2.5) 2.6 Compatibility Requirements This device passes the following compatibility requirements. # Feature Detailed Description 2.6.1 Wi-Fi Ÿ 2.6.2 WHQL Ÿ 2.6.3 Physical Layer and Functionality Ÿ Meet Wi-Fi certification for IEEE 802.
Alpha Networks Proprietary and Confidential Information 9
Appendix I: Rate Dependent Parameters for High Throughput .
Test Equipment/測試設備列表 English EQUIPMENT NO. Q’TY 1 IQ-View 1 2 Shielded Box (530 * 280 *160 mm) made of Copper 1 3 Splitter (1 * 3) 1 4 RF CABLE 4 5 PC (with monitor) 1 7 USB 2.0 / PCI / MINI PCI / CARD BUS Interface 1 8 Test connect (HIROSE / IPEX) 3 9 Fixed Attenuator (20dB) 1 10 Power supply 1 中文 項次. 設備名稱 數量 1 IQ-View 1 2 隔離箱 (530 * 280 *160 mm) made of Copper 1 3 分配器(1 * 3) 1 4 RF 線 4 5 PC (with monitor) 1 6 PCI GPIB 控制卡 或 USB GPIB 控制卡 1 7 USB 2.
Test Environment Diagram/測試環境圖示 Splitter (1 對 3) IP: 192.168.100.
Normal Test Operating Procedure/一般作業用測試操作程序 1. Testing Steps: 6 steps in total 1. 測試步驟: 共 6 個步驟 註 1:測試前請先安裝待測物之 driver. 註 2:測試前請先依照附錄(Test Programming Setup & Test Program Install step / 測試程式設定和測試環境架設說明)設定 [Step 1] Run ”ATEToolRT28xx” at DUT (see Figure 1) to open test window (see Figure 2).
[Step 2] Select test model, Then Kevin W.O Number and Serial number and Worker ID and Site Name.
[Step 3] (a) Plug DUT into USB 2.0 / PCI / MINI PCI / CARD BUS Interface (b) Plug RF Cable on DUT antenna point. (MAIN) [步驟 3] (a) 將待測物插入 USB 2.0 / PCI / MINI PCI / CARD BUS Interface 介面。 (b) 將待測物接上測試線於天線端。(MAIN) [Step 4] Click “START” to begin test.
[Step 5] When test finish, it will show “PASS”(see Figure 5).
Test Program setup / 測試程式設定 [步驟 1] 按下程式中”Config” 選項 (如圖 1)，並輸入密碼 “admin(測試用)”。 (如圖 2) (Figure 1) (Figure 2) 17
[步驟 2] 仿照以下圖形及數據去設定程式，完成後按下”ok” 註 1: 請 Import 檔案(1WMPND02..A1G.
Test Program Install step / 測試環境架設說明 1.將測試設備接線完畢 2.準備乾淨的 windowsXP 環境 3.將測試程式複製至資料夾中 4.安裝測試程式資料夾內的 ANIO Protocol Driver 資料夾裡所附的 ANIO.exe 5.安裝待測物網卡的驅動程式 6.Calibration 測試環境,測試時加入一衰減器 20dB 測試. 7.
F ed er al Co m mu n i c ati o n Co mmi ssi o n I n t erf er en c e Sta te men t This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 3.21dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
以下警語適用台灣地區： 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更 原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無 干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻射性電機設備之干擾。 在 5.25-5.
