Installation Guide For WMP-ND03 Alpha Networks Proprietary and Confidential Information 1
Operation Manual Test Utility Installation: 1. Unzip “ART_V0_5_b25ALL.zip” to “C:\”. 2. The utility must run on Win2000 or WinXP. Hardware Installation: Before insert the card, please execute the below instruction at first !! 1. Win2000 OS : Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\2000 Execute the uninst_new_drv_2k.bat: Execute the inst_new_drv_2k.bat : WinXP OS : Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\xp Execute the uninst_new_drv_xp.bat: Execute the inst_new_drv_xp.bat 2.
2. Continuous Transmit Options. a. Before the Continuous Transmit test, need to press “e” first The command will load the calibrate data to the EEROM, then the card can transmit the target power b. The channel frequency, data rate and output power could be changed in continuous transmit options. Press “c” to increase the output power , 11g Power (data rate 6Mbps) is 17dBm, 11b Power is 17dBm , Press ESC to return to the main Test Options menu when finished. 3.
1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11 a/b/g/n Mini-PCI Card. This mPCI is based on Atheros chipset that complied with complied with IEEE 802.11n Draft 2.0, and it is also backward complied with IEEE 802.11a standard from 5.15~5.825GHz wideband and IEEE 802.11b/g standard from 2.4~2.5GHz. It can be used to provide up to 54Mbps for IEEE 802.11a and IEEE 802.11g , 11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n to connect your wireless LAN. 1.
2.1 Functional Block Diagram 2.0V LDO EEPROM 40MHz CXO 2/5 GHz PDET and Control Chain 0 2GHz Rx Chain 0 DAC/ADC BASEBAND 5GHz Rx Chain 0 5GHz Tx Chain 0 CONTROL LINES FEM ANT_CON FEM ANT_CON 2GHz Tx Chain 0 Mini-PCI CONNECTOR LED 2GHz Rx Chain 2 5GHz Rx Chain 2 AR9160 AR9106 5GHz Tx Chain 2 2GHz Tx Chain 2 2/5 GHz PDET and Control Chain 2 2GHz Rx Chain 1 5GHz Rx Chain 1 5GHz Tx Chain 1 2GHz Tx Chain 1 3.3V SUPPLY 1.8V 1.
# Feature Detailed Description 2.2.1.4 2.2.1.5 Data Rate Media Access Protocol Maximum Transmitter Output Power at Antenna Connector y 54, 48, 36, 24, 18, 12, 9 and 6Mbps y CSMA/CA with ACK Receiver Sensitivity at Antenna Connector y Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = 10% and at room Temp. 25degree C y –dBm at 54Mbps y –dBm at 48Mbps y –dBm at 36Mbps y –dBm at 24Mbps y –dBm at 18Mbps y –dBm at 12Mbps y –dBm at 9Mbps y –dBm at 6Mbps (TBC) 2.2.1.6 2.2.1.
# Feature Detailed Description 2.2.3.5 2.2.3.6 Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector y 6,9,12,18,24,36,48,54Mbps y CSMA/CA with ACK 2.2.3.7 Typical RF Output Power atRF each RF Data chain, Data andTemp. at y ʳTypical RF Output Power at each chain, Rate andRate at room room 25degree C Temp.
# 2.2.4.5 2.2.4.6 Feature Media Access Protocol Maximum Transmitter Output Power at Antenna Connector Detailed Description 8 13 9 26 10 39 11 52 12 78 13 104 14 117 15 130 y CSMA/CA with ACK 27 54 81 108 162 216 243 270 14.444 28.889 43.333 57.778 86.667 115.556 130.000 144.444 30 60 90 120 180 240 170 300 y Typical RF Output Power at each RF chain, Data Rate and at room Temp.
y Security Supports enhanced security WEP, 802.1x,WPA, WPA2. 2.3.1 Security # Feature Detailed Description 2.3.3.1 Encryption 2.3.3.2 WEP Management 2.3.3.3 2.3.3.4 802.
# 2.8.3 2.8.4 Feature Detailed Description Temperature Conditions performance is degraded when restored to the operating temperature after exposing to storage temperature in the range of –20 к to +75 к. y The product is capable of continuous reliable operation when subjected to relative humidity in the range of 10% and 90% noncondensing.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required.
Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 7.12dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada.
פ܅୴᙮ሽᖲհࠌشլᐙଆڜ٤֗եឫٽऄຏॾΙᆖ࿇ڶեឫွழΔᚨ ܛمೖشΔࠀޏ۟ྤեឫழֱᤉᥛࠌشΖছႈٽऄຏॾΔਐࠉሽॾऄࡳ܂ᄐհ ྤᒵሽຏॾΖפ܅୴᙮ሽᖲႊٽ࠹ݴऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭شሽंᘿ୴ࢤሽᖲ ໂհեឫΖ ءᑓิ࣍࠷ᎁᢞ৵ലࠉࡳ࣍ᑓิ᧯ءᑑقᐉٽ᧘ΔࠀؓޣՂᑑقψءข փܶ୴᙮ᑓิΚID ᒳᇆω
