User’s Manual For USB Module Model Number : WUS-N19D Revision: 1.
Test Utility Installation: Hardware: BCM43235 RGMII INIC test fixture, with gigabit Ethernet port computer Software: RT3x5x MII V1.0.1.0 1. Insert WUS-N19D to BCM43235 RGMII INIC test fixture, connect the test fixture to computer with Ethernet cable 2. Use RT3x5x MII V1.0.1.0, make sure the computer has installed the wincap.exe 3. Select GIGABIT INIC 4.
1.1 Document This document is to specify the product requirements for USB Module. This iNIC Card is based on BCM43235 single chipset that complied with complied with IEEE 802.11n Draft 2.0, IEEE 802.11 b/g standard from 2.4~2.5GHz. It can be used to provide up to 54Mbps for IEEE 802.11g , 11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n to connect your wireless LAN. 1.
2.0 Requirements The following sections identify the detailed requirements of the USB Module . 2.2 General Requirements 2.2.1 IEEE 802.11b Section # Feature Detailed Description 2.2.2.1 2.2.2.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers y y IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK y 2400 ~ 2483.
# Feature Detailed Description y y y y y y y –86 dBm at 9Mbps –84 dBm at 12Mbps –82 dBm at 18Mbps –79 dBm at 24Mbps –75 dBm at 36Mbps –71 dBm at 48Mbps –70 dBm at 54Mbps 2.2.3 IEEE 802.11n Section for 2.4G Band # Feature Detailed Description 2.2.4.1 2.2.4.2 Standard Radio and Modulation Type Operating Frequency Data Rate Media Access Protocol Transmitter Output Power y y IEEE 802.11n BPSK, QPSK, 16QAM, 64QAM with OFDM y y y 2400 ~ 2483.
2.3.1.2 2.31.3 2.3.1.4 2.3.1.5 Operating Voltage Current Consumption Form Factor and Interface LED y y y y 3.3VDC +/- 10% 450 mA at continuous transmit mode (2 Tx chains on ) 250 mA at continuous receive mode (2 Rx chains on ) USB form factor y External LED function supported 2.4 Software Requirements The Configuration Software supports Linux2.6. This configuration software includes the following functions: y Information Information allows you to monitor network status.
# Feature Detailed Description y 2.4.3.2 WEP Management y y 2.4.3.3 2.4.3.4 802.1x WPA/WPA2 y y y y Support open system (OSA) and shared key authentication (SKA) Four WEP keys can be selected STA with WEP off will never associate any AP with WEP enabled WEP Key Format: Option for Hex format Support EAP-TLS, EAP-TTLS, and EAP-PEAP Support WPA/WPA2-PSK and WPA/WPA2-EAP Support Cipher Mode AES and TKIP 2.5 Mechanical Requirements # Feature Detailed Description 2.5.1 2.5.2 2.5.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
