User's Manual

ManualsBrandsAlpha Networks ManualsElectronics802.11a/b/g/n WIFI Dongle

Before Use

Precautions for use

• Keep this product and this accessory out of the

reach of children.

• This product is for use with the Unique 1.0 m /

3.281 ft extension cable only.

• Do not place this product in a location near

a heat source, or a place subject to direct

sunlight. Doing so may cause a distortion or

malfunction.

• Keep this product away from ﬂ ammable

objects or naked ﬂ ame sources (such as

lighted candles).

• Do not repair this product by yourself. Refer

servicing to qualiﬁ ed personnel only.

Introduction

This product is the wireless adapter with a USB

connector. It is for use with Blu-ray DiscTM Player

only. You can use this product by connecting it to

the USB port of a system.

FCC Compliance Statement

This device complies with Part 15 of the FCC

Rules.

Operation is subject to the following two

conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any interference

received, including interference that may cause

undesired operation.

Interference: This equipment has been tested

and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Wireless Radio

For product available in the USA and Canada

market, only channel 1–11 can be operated.

Selection of other channels is not possible.

The device could automatically discontinue

transmission in case of absence of information

to transmit, or operational failure. Note that this

is not intended to prohibit transmission of control

or signaling information or the use of repetitive

codes where required by the technology.

If this device is going to be operated in 5.15–

5.25GHz frequency range, then it is restricted in

indoor environment only.

Important: Any changes or modiﬁ cations not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate this equipment.

This device and its antenna (s) must not be co-

located or operating in conjunction with any other

antenna or transmitter.

FCC Radiation Exposure Statement: This

equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment.

This equipment should be installed and operated

with minimum distance 20 cm between the

radiator & your body.

Speciﬁcations

Standards Compliance:

IEEE 802.11a/b/g/n

Host Interface:

USB 2.0

Authentication Mode:

WPAPSK, WPA2PSK

Encryption Type:

WEP, TKIP, AES

Frequency and Channel*1:

2.412 GHz – 2.462 GHz [CH1 – 11]

5.15 GHz – 5.25 GHz [CH36 – 48]

5.25 GHz – 5.35 GHz [CH52 – 64]

5.47 GHz – 5.725 GHz [CH100 – 140]

5.725 GHz – 5.85 GHz [CH149 – 165]

Power Consumption:

2.2 W

Mass (Approx.):

USB Wireless LAN Adapter: 15 g

Dimensions (Approx.) (w × h × d):

USB Wireless LAN Adapter:

73.3 mm × 26.6 mm × 10.5 mm

Design and speciﬁcations are subject to

change without notice.

*1 The frequency and channel differ depending

on the area.

Standards Compliance

• Compatible with IEEE 802.11a/b/g and

802.11n.

Note

• The location where the transmission is most

effective differs depending on the usage

environment. In this case, use the Unique 1.0

m / 3.281 ft extension cable.

• Check precautions and instructions about the

usage location of the product. For details, refer

to the operating instructions of each product.

Accessories

• USB Wireless LAN Adapter (1)

• Unique 1.0 m / 3.281 ft extension cable (1)

• Operating Instructions (this manual) (1)

USB WiFi Adapter for Blu-ray Disc

/DVD Player

WUS-ND12B

OWNER’S MANUAL

For USA

USA-Federal Communications Commission Statement

Conﬁguring a wireless Internet connection

This section describes how to conﬁgure the Blu-ray Disc

player for accessing the Internet via a WiFi

connection. The procedure for connecting to a wireless network depends on various network arameters.

Read the following conﬁguration methods to determine which instructions to use to onnect to your

network.

Wireless Setting

If no Ethernet cable is connected to the ETHERNET jack of your player, you can connect this USB

WiFi adapter to your player and then select “Interface -> Wireless” in the Network setting menu and the

following screen appears:

LED Indicator

2. Manual mode (connection to the Wireless Network via your input SSID)

1) Press / to select Auto, then press OK.

The following screen appears.

3) Press OK to activate the on-screen keyboard. Carefully enter the network password by using the

, , / to highlight the desired letter on the keyboard, and then press OK. (If you make a

mistake, use , , / to highlight Back on the keyboard and press OK to erase the mistake.

Or highlight Clear on the keyboard and press OK to clear them, them enter again.)

4) Use

, , / to highlight Enter on the keyboard, and then press OK.

If the wireless network is functioning, a message “Connection success and IP is obtained” will

appear on the TV.

5) Press OK to close the message. The Blu-ray

disc player is now connected to the network.

From now on, when you turn on the player, it will automatically connect to the network; there is no

need to repeat these steps again.

Notes:

• If you do not see this message, the Blu-ray Disc

player was not able to connect to the network.

• If the wireless network is encrypted using an unsupported encryption, you cannot connect to the

network. You must change the router’s encryption type before proceeding.

LED Behavior

Inactive Turned Off

Active Keep blinking

Wireless setting

Scan

Manual

Auto

LED indicator

1. Scan mode (select the Wireless Network which you scanned)

1) Press / to select Scan, then press OK. A list of existing wireless networks near the Blu-ray

Disc

player will appear (It may take several seconds for this list to be created). For example:

2) Press

/ to select the desired wireless network, and press OK to conﬁrm.

a. If the Blu-ray DiscTM player is connected to an Unencrypted Wireless Network, it will

display "NONE" in the Security list and there is NO need to enter the password.

If the wireless network is functioning, a message “Connection success and IP is obtained” will

appear on the TV.

3) Press OK to close the message. The Blu-ray

disc player is now connected to the network. From

now on, when you turn on the player, it will automatically connect to the network; there is no need

to repeat these steps again.

Note:

• If you do not see this message, the Blu-ray Disc

player was not able to connect to the network.

b. If the Blu-ray DiscTM player is connected to an Encrypted Wireless Network, a menu

similar to the following will appear:

3. Auto (connection to the Wireless Networks Using WPS <Wi-Fi Protected Setup>)

1) Press / to select Auto, then press OK.

2) Use

/ to select PBC or PIN.

3) Follow the instructions to continue operating the connection.

2) Press OK to activate the on-screen keyboard and enter the SSID your desired.

3) Use

, , / to highlight Enter on the keyboard, and then press OK.

4) Follow the instructions to continue operating the connection.

Summary of content (3 pages)

PAGE 1
USB WiFi Adapter for Blu-ray DiscTM/DVD Player Wireless Setting WUS-ND12B If no Ethernet cable is connected to the ETHERNET jack of your player, you can connect this USB WiFi adapter to your player and then select “Interface -> Wireless” in the Network setting menu and the following screen appears: Wireless setting Scan Manual Auto OWNER’S MANUAL For USA Before Use 1.
PAGE 2
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
PAGE 3
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.