ALPHATECH TECHNOLOGIES s.r.o. Jeremenkova 88, Praha 4, Czech Republic www.alphatechtechnologies.
Contents 1 2 3 4 5 6 7 8 2 BASIC DESCRIPTION ....................................................................................... 3 1.1 FEATURES ...................................................................................................... 3 1.2 SLIMDOORPHONE MODELS ............................................................................ 4 INSTALLATION ................................................................................................. 4 2.
1 Basic description 1.1 Features Very slim module for surface mounting only. Supplied in 1, 2 or 4 button variants. Possibility connection keyboard with second relay. Voice communication powered from analogue telephone line only.
1.2 SlimDoorPhone models Three versions are available plus keyboard : SDP01 -1 button SDP02 -2 buttons SDP04 -4 buttons Keyboard 2 Installation This compact unit is fixed by 2 screws to the wall. 2.1 Opening, wiring, wall mounting and settings 2.1.1 Name card panel 1. Every unit is supplied with a special key which is used to release the name cards on the front panel. Push the key into the hole in the speaker grille (see figure - 1). 2.
2.1.2 Uncover control elements 4. Push the aluminium speaker grille down (see figure – 4). 2.1.3 Wiring and wall mounting 5. Use the wall mounting template at the end of the manual to mark the position for the screw holes and cable connection on the mounting surface. Drill the holes. 6. Feed the cable (analogue line, power supply, lock – see figure - 6) through the cable hole. Fix the panel to the wall using the screws and rawlplugs supplied.
The wiring of relay contacts is explained in the next picture. The symbol "NO" means contact normally open, "COM" means sharing output (central) and "NC" means contact normally closed. The relay contact is isolated from the other circuits on the board. For the variants of lock connection see the picture below. Telephone line Power supply lock Wiring of standard and magnetic (inverse) lock 7. A special USB cable enables the doorphone to be connected to a PC for programming of individual parameters.
The PCB heating has two major benefits. Firstly, it warms the board during winter time (temperatures under -20 C, most circuits have warranty operation down to -20 C) and secondly it helps to protect the PCB against humidity when installed outside. 2.1.5 Voice level 10. Voice communication – the trimmer position is factory and should be suitable for most installations. Change the trimmer position only when necessary. The trimmer "MIC" is designed for microphone volume setting.
2.2 Location of Doorphone components All mounting, control and setting elements are located under the speaker front aluminium grille. SPK- setting of speaker volume MIC-setting .
2.3 Changing name cards Name card panel (2.1.1on page 4) has spaces to insert printed name cards. Insert name cards from top (see picture). Cards can easily be printed with pictures as well as text using the included software. The card outline is marked for easy cutting . pocket Panel with cards 2.4 Final closing of Doorphone 2.4.1 Covering control elements 1. Push aluminium speaker cover back up (see picture). Take care when re-covering the speaker.
2.5 Connect the Keyboard Keyboard work as separate code lock, he has connection power supply 12V, input for departure button and one relay with change-over contact. In case connection by special cable keyboard with SlimDoorPhone characteristics those code lock expand and keyboard can be use not only to control relay in keyboard, but relay in doorphone SlimDoorPhone contol too and use so 10 codes for one and 10 codes for second relay. Further it is possible keyboard use to dialling numbers.
3 SlimDoorPhone Services 3.1 Signalling Overview The unit signals acoustic conditions that may occur during operation. You can listen to the signalling samples in the SlimDPset program. Condition Tones Tone frequency Pick up line –▄–■–▀– 425-850-1275 Hang up line –▀–■–▄ 1275-850-425 ––█–– 425 Confirm command Dialling DTMF/Pulse Call Conversation end warning –■–■–■– 1275 Enter programming (phone or PC) –■–■–■– 850 ––▓–▓––––– mod.
from the second group (parameter 2). The next press of the same button again selects the number from the first group, etc..…… If the button is pressed after the line has been opened (but before the call is answered), the unit will hang up for the period given by parameter 54, lift up the line and dial the other group number. The relay can be controlled by pressing the buttons in the combination that is set in the preprogrammed code (parameters 32-34).
If, within the first 10 seconds, the service password is entered, the unit will switch to programming mode and voice communication will cease. During an incoming call it is possible to restrict relay control (parameter 37). This can be useful in some special applications. 4 Parameter programming 4.1 Programming from a telephone by DTMF 4.1.1 Entering programming mode The SlimDoorPhone may be set to programming mode in two ways: 1.
The unit stays inactive in programming mode for 34 seconds and will then automatically hang up. Every time a DTMF tone is dialled, this period is reset. Alternatively, parameter 9 may also be selected to end programming mode. To program a parameter, enter the parameter number followed by the value you wish to set. The unit will either respond with the Parameter Confirmation Tone, or one of the Error Tones. Note 1. if you wish to maintain the connection in programming mode (i.e.
5 Parameter description 5.1 Direct Dialling – Memories Parameter Value 1 t nn… Description Default No. nn under button t t – Button number (memory) [1-4] nn – telephone number up to 16 digits to be stored. Refer to the table for other choices. The number stored in parameter 1 is the number for the first group or the number for Day mode. Parameter Value 2 t nn… Description - parameter 0-9 # * Recall Pause dial 0-9 # ** *# *0 Default No.
Parameter Value Description Default 32 hhhhhh External access code in DAY + NIGHT mode - 33 hhhhhh External access code in DAY mode - 34 hhhhhh External access code in NIGHT mode - hhhhhh – password for relay closing from buttons [2 to 6 digits] The 3 passwords are controlled by Day/Night; the combination is entered using the unit buttons. It is influenced by the setting of Relay mode and Day/Night switchover. When set to 2-group mode the unit is permanently in DAY mode.
Parameter Value Description 38 cc Default 66 Internal access code 2 impulses cc – command from phone to relay closing [2 digits] – 2 impulses Parameter Value 39 hhhhhh Description Default External access code in DAY + NIGHT mode for 2 impulses 66 hhhhhh – password for relay closing from buttons [2 to 6 digits] for activation 2 impulses in DAY and NIGHT mode.
Parameter Value 43 Description bb Default End call 55 bb – command for unit hanging up from phone [2 digits] It is recommended to set the same command for both Internal Access Code (parameter 35) and End Call aa=bb.
Parameter 52 Value d Description Default d – maximum time in minutes for which a call may last. This time can be extended during a call by dialling Prolong Call digit from telephone (* setting is per table. Parameter 53 Value w 2 Maximum call duration Description time [min] 0,5 1-9 15 30 choice 0 1-9 * # Default time between button presses 2 w – max.
Parameter Value 57 Description Default t DTMF tone duration (ms) 5 (100ms) 58 m Space duration between DTMF tones (ms) 5 (100ms) 59 f Recall duration (ms) 1 (100ms) 50 p Pause duration (ms) 8 (800ms) – DTMF tone duration is determined by the formula: (entered number + 5) x 10 = tone duration [ms] [range 1-0 i.e. 60-150ms] m – Space duration between DTMF tones is determined by the formula: (entered number + 5) x 10 = gap duration [ms] [range 1-0 i.e.
Parameter Value 5*2 y Description Default 4 Frequency of tone detection y – setting range frequency of tone detection from telephone line, value is in next table: y frequency range y frequency range 1 200-350Hz 7 500-650Hz 2 250-400Hz 8 550-700Hz 3 300-450Hz 9 600-750Hz 4 350-500Hz 0 650-800Hz 5 400-550Hz * 700-850Hz 6 450-600Hz # 750-900Hz Parameter Value 5*3 z Description Default 0 Time of continuous tone before hang up z – time of continuous tone before hang up.
Parameter Value Description Default Deletes all numbers in group 1 (Day mode) Deletes all numbers in group 2 (Night mode) 81 82 83 Default setting only for parameters 3x only 3.. 84 Default setting only for parameters 4x only 4.. 85 Default setting only for parameters 5x only 5.. The parameters 81 and 82 will delete all numbers stored in memories for buttons. The parameters 83 – 85 will execute a selective basic setting only for parameters starting with 3.. – 5..
Parametr 6 Value z Description Default Acoustic signalling 3 and 9 In default the unit produces acoustic signals. It can occasionally cause a problem of incorrect detection of tones by PBX. By changing parameter „z“ you can switch off this acoustic signalization.
37 pp Time between 2 impulses 05 38 cc Internal access code 2 impulses 66 39 hhhhhh External access code in DAY + NIGHT mode for 2 impulses - 30 kk Internal access code for relay in keyboard 77 41 v Dialling type 0 42 z Proling call * 43 bb End call 55 44 xxxx Password 0000 45 dd DAY MODE switching 11 46 nn NIGHT MODE switching 10 47 e Dialling mode 1 51 q Number of rings before pick-up 2 52 d Maximum call duration 2 53 w Time between button presses
81 82 83 84 85 Deletes all numbers in group 1 (Day mode) Deletes all numbers in group 2 (Night mode) Default setting only for parameters 3x Default setting only for parameters 4x Default setting only for parameters 5x 9 only 3.. only 4.. only 5.. END 6 Technical parameters 6.
6.2 Mechanical dimensions Dimensions WxHxD Weight Unit material Name card panel material 104mm x 153mm x 16mm 360g elox aluminium profile acrylglas (plexiglass) 7 Table for easy programming Complete the values you want to program in the empty part of table on the next page. All programming commands are located in the double-framed area, to simplify programming. Retain a copy for future reference. Use Description Programming sequence par. Number under button 1 Day/Gr.
Internal access code for relay in keyboard Dialling type 30 2 41 1 Prolong call 42 1 End call 43 2 Password 44 4 DAY MODE switching 45 2 46 2 47 1 51 1 1/0 NIGHT MODE switching Dialling mode 1/0 No.
8 Drilling master board 28
ALPHATECH TECHNOLOGIES s.r.o. Jeremenkova 88, Praha 4, Czech Republic www.alphatechtechnologies.cz ALPHATECH TECHNOLOGIES s.r.o. Jeremenkova 88 140 00 Praha 4 Czech Republic VAT: CZ27577350 Company is registered in the Commercial Register administered by the Municipal Court in Prague, Section C, Record 116886 Banking details: Komerční banka, account No.
