ALPHAGUARD 2000 TELEPHONE-ENTRY AUTODIALER INSTALLATION & PROGRAMMING MANUAL AWD165 Rev.
ALPHAGUARD 2000 Series Autodialer SYSTEM FEATURES Capacity for up to 1000 Tenants. Simple Upgrade from Autodialer to No Telephone Line System. Handsfree or Handset operation. Field Programmability using system keypad. High Contrast LCD user Display. Zinc Die-cast Marine Quality Keypad. E2PROM Memory, retains programmed information during total power failure. Superior Lightning & Transient Protection. Two Programmable Relay outputs to control door strikes, gates, cameras, etc.
ALPHAGUARD 2000 Series Autodialer Installation Manual for 2000 Series Telephone-Entry Autodialer TABLE OF CONTENTS Page 1.0 Installation Hints .................................................................................................. 1 2.0 2.1 2.2 2.3 2.4 2.5 2.6 Special Features ................................................................................................. Postal Service Lock .............................................................................................
ALPHAGUARD 2000 Series Autodialer 1.0 INSTALLATION HINTS Arrangements should be made with the telephone company for the installation of a telephone line for use by the system. It is recommended that the telephone jack be installed inside the entry panel enclosure. One 16 Volt/20 VA CSA approved Class 2 power transformer is required for system operation. A second transformer is required for door strike activation.
ALPHAGUARD 2000 Series Autodialer 2.0 SPECIAL FEATURES (cont.) 2.3 Auxiliary Relay Activation The system includes a Form C auxiliary relay contact that can be momentarily activated from the suite telephone by dialing the digit 6 when the tenant is in conversation with the visitor at the entry system. This contact can be used to trigger a parking gate, elevator, secondary door or video camera. 2.
ALPHAGUARD 2000 Series Autodialer 3.0 INSTALLATION - Refer to SYSTEM WIRING DIAGRAM (Appendix B) 1. Mount the system enclosure to the wall in a location close to the building's controlled entry point. 1. Connect the door strike wires to terminals D1 and D2 for D.C. (silent) operation or to terminals D3 and D4 for A.C. (buzzing) operation. Do not exceed maximum switched door strike load of 28 volts at 3 Amps. 1.
ALPHAGUARD 2000 Series Autodialer 4.0 SYSTEM PROGRAMMING All programming of the entry system is accomplished through the use of the system keypad and the display located on the control panel. Use the supplied Directory Worksheets to generate a record of the building occupants, their suite telephone numbers, assigned dial codes and keyless entry codes. These sheets will be required for programming and in the event that changes are to be made.
ALPHAGUARD 2000 Series Autodialer Tenant Code Review and Delete Press the '#' key to select this function when the program menu displays " VIEW TENANT CODES". The message "CODE TO REVIEW, ______" will appear. Enter the four digit code to be reviewed. The code and associated telephone number will then appear on the display. If the code and telephone number are to be deleted, press the '#' key while they are being displayed.
ALPHAGUARD 2000 Series Autodialer 4.4 System Master Code The Master Code is used to allow access to the "Program Mode". When the entry system is shipped from the factory, its master code is set to * 1 2 3 . It is recommended that the master code be reprogrammed and the new code be inserted in the appropriate place on the Programming Worksheet (Appendix C). This code is only to be used when programming is necessary by the installation company or by authorised personnel.
ALPHAGUARD 2000 Series Autodialer 4.7 Door Timer Selection The door open time can be selected to be from 0 to 99 seconds, (factory default is 10 seconds). Press the '#' key to select this function when the programming menu displays the message "DOOR TIME". The message "DOOR OPEN TIME" will appear. Enter a two digit time in seconds and press the '#' key to store. Press the '*' key when finished to exit this mode and return to the programming menu. Press the '*' key to exit the program mode if desired. 4.
ALPHAGUARD 2000 Series Autodialer 5.0 ADJUSTMENTS 5.1 Volume Control The communication volume levels come factory preset for normal operation. The levels can be increased or decreased by adjusting the potentiometers located along the bottom of the system controller located behind the front display plate. Audio level from the entry system to the suite is controlled by the MIC. VOLUME control and the level from the suite to the entry system by the SPEAKER VOLUME control. 5.
ALPHAGUARD 2000 Series Autodialer APPENDIX A REGULATORY APPROVALS IMPORTANT NOTICE The following information is provided to the installation contractor for compliance with Industry Canada Standards. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Industry Canada does not guarantee that the equipment will operate to the user’s satisfaction.
ALPHAGUARD 2000 Series Autodialer INSTRUCTION TO THE U.S. USER FCC REQUIRED INFORMATION FCC REGULATIONS This device has been granted a registration number by the FCC, under part 68 rules and regulations governing devices that directly connect to the telephone lines. This equipment complies with Part 68 of the FCC rules. A label on the controller housing of the AlphaGuard 2000 contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment.
ALPHAGUARD 2000 Series Autodialer APPENDIX B SYSTEM WIRING DIAGRAM SYSTEM POWER 16 VAC 20 VA INTERNAL N.O. DOOR CONTACT TERM.T4 & D4 DOOR STRIKE TRANSFORMER D.C. (SILENT) DOOR STRIKE A.C.
ALPHAGUARD 2000 Series Autodialer APPENDIX C PROGRAMMING WORKSHEET Installing Dealer: _________________________ Tel. __________________________ Building Address: _______________________________________________________ Installation Date: ___________________ System Tel. Line # : ___________________ Programming Instructions: A. Enter System Master Code from keypad to access the programming menu. B. Use the '1' and '3' digits on the keypad to scroll the menu screen. C.
ALPHAGUARD 2000 Series Autodialer DIRECTORY WORKSHEET TENANT SUITE # TENANT NAME TENANT TELEPHONE # 13 DIAL CODE KEYLESS ENTRY CODE
ALPHAGUARD 2000 Series Autodialer DIRECTORY WORKSHEET TENANT SUITE # TENANT NAME TENANT TELEPHONE # 14 DIAL CODE KEYLESS ENTRY CODE
ALPHAGUARD 2000 Series Autodialer DIRECTORY WORKSHEET TENANT SUITE # TENANT NAME TENANT TELEPHONE # 15 DIAL CODE KEYLESS ENTRY CODE
ALPHAGUARD 2000 Series Autodialer USER OPERATING INSTRUCTIONS A DoorGuard Intercom System has been installed in your building to provide increased security for you and your visitors. The system provides communication and entry control using your telephone. Visitors simply enter your code number from the directory to ring your suite. You can answer from any telephone. To permit entry, dial the digit "9". To deny entry, simply hang-up. Do not dial "9".
