Split Inverter Air Conditioner OWNER'S MANUAL ALPICAIR AIR CONDITIONERS Thank you for selecting ALPICAIR air conditioners. Please read this 66129909213 manual carefully before operation and keep it for further reference.
CONTENTS Operation and maintenance ■ Notices for operation ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１ ■ Notices for use．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．３ ■ Names and functions of each part ．．． ．．．．．．．．．．．．．．．．．．．４ ■ Operation of wireless remote control ．．．．．．．．．．．．．．．．．．．．．５ ■ Emergency operation ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１０ ■ ■ Clean and care ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１１ Troubleshooting．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．１３ Installation service ■ ■ ■ ■ ■ Notices for installation ．．．．．．．．．．．．．．．
Notices for operation Please read the following carefully before operating ★ When the voltage is very high, the components would be easily damaged, when the voltage is very low, the compressor vibrates terribly and that the refrigerant system will be damaged, the compressor and electric components cannot work, the voltage should be stable; there shouldn’t be big fluctuation. ★ Don’t leave windows and doors open for a long time while operating the air conditioner.
Notices for operation ★ Please don't cut off or damage the power cords and control cords. If they are damaged, please ask the qualified personnel to change them. ★ To adjust the airflow direction appropriately. When operating the unit,to adjust the vertical and lateral air flow direction by use of remote controller. Swing louver ★ Don’t insert your hands or stick into the air intake or outlet vents. Guide louver ★ Don’t blow the wind to animals and plants directly.
Notices for use Working principle and special functions for cooling Principle: Air conditioner absorbs heat in the room and transmit to outdoor and discharged, so that indoor ambient temperature decreased, its cooling capacity will increase or decrease by outdoor ambient temperature.
Names and functions of each part Indoor unit Air in ⑴ ⑵ Air out ⑶ ⑸ ⑷ ⑻ ⑴ Front panel ⑵ Filter ⑶ Guide louver ⑷ Wall pipe ⑹ ⑸ Bind tape ⑹ Connection pipe ⑺ Drainage pipe ⑺ ⑻ Remote control 4
遥控器各按键的名称及作用 Operation of wireless remote control Name and function of wireless remote control Note: Be sure that there are no obstructions between receiver and remote controller; Don't drop or throw the remote control; Don't let any liquid in the remote control and put the remote control directly under the sunlight or any place where is very hot. Signal transmitter SLEEP SLEEP button ● Press this button, Sleep On and Sleep Off can be selected. After powered on,Sleep Off is defaulted.
Operation of wireless remote control Names and functions of wireless remote control This wireless remote control is universal, and it could be used for many units, some buttons of this control which are not available to this unit will not be described below. + + button ● Presetting temperature can be increased.
Operation of wireless remote control Name and function of wireless remote control This wireless remote control is universal, and it could be used for many units, some buttons of this control which are not available to this unit will not be described below. TIMER ON TIMER ON BUTTON ● Timer On setting: Signal “ON” will blink and display, signal will conceal, the numerical section will become the timer on setting status.
Operation of wireless remote control Guide for operation- General operation 1. After powered on, press ON/OFF button, the unit will start to run.(Note: When it is powered on, the guide louver of main unit will close automatically.) 2. Press MODE button, select desired running mode. 3. Pressing +or - button, to set the desired temperature (It is unnecessary to set the temp. at AUTO mode.) 4. Pressing FAN button, set fan speed, can select AUTO FAN, LOW, MID and HIGH. 5. Pressing button, to select the swing.
Operation of wireless remote control ★ About lock Press +and - buttons simultaneously to lock or unlock the keyboard. If the remote controller will be displayed on it, in which case, press any button, the mark will is locked, the icon flicker for three times. If the keyboard is unlocked, the mark will disappear. ★ About swing up and down 1.
Emergency Operation Emergency Operation When the wireless remote control is lost or damaged, please use the manual switch, at this time, it is running in Auto Run mode that will not change the temperature setting value and fan speed. The manual switch can be operated as follow: ● ● At operation: When the unit stopped running, press ON/OFF button, unit will enter into AUTO RUN mode.
Clean and care CAUTION ● ● Turn power off and pull out the power plug before cleaning air conditioner. Or it may cause electric shock. Never sprinkle water on the indoor unit for cleaning because it can cause an electric shock. Volatile liquid (e.g. thinner or gasoline) will damage the air conditioner. (So wipe the units with a dry soft cloth, or a cloth slightly moistened with water or cleanser.
Clean and care ① Take down the air filter At the slot of surface panel to open an angle, pull the air filter downward and take it out. (b) ② Cleaning To clean the dust adhering to the filters, you can either use a vacuum cleaner, or wash them with warm water (the water with the neutral detergent should below 45 ℃). When the filters are very dirty (such as oil stain), and dry it in the shade. NOTE: Never use water above 45 ℃ to wash, or it can cause deformation or discoloration.
Troubleshooting Warning Do not repair the air conditioner at your discretion. Incorrect repair may cause electric shock or fire, so please contact Authorized Service Center for professional repair. Following checks prior to contact may save your time and costs. Troubleshooting Phenomenon The unit can not operte immediately ● when the air conditioner is restarted.
Troubleshooting Phenomenon Creaking noise can be heard when start or stop the unit. Air conditioner does not operate at all. Troubleshooting This is caused by the deformation of plastic due to the change of temperature. ● Has the power been shut down? ● Is the wiring loose? ● ● Is voltage higher or lower? ● Is TIMER ON in operation? ● Is SET TEMP. suitable? Is air inlet or outlet obstructed? Breaking off Cooling(Heating)efficiency is not good.
Troubleshooting Troubleshooting Phenomenon Indoor unit cannot deliver air In HEAT mode, when the temperature of indoor heat exchanger is very low, that will stop deliver air in order to prevent cool air. (Within 3min) ● In HEAT mode, when the outdoor temperature is low or high humidity, there are much frost be formed on the outdoor heat exchanger, that the unit will automatically defrost, indoor unit stop blowing air for 3-12mins.During the defrosting, there is water flowing out or vapor be produced.
Installation service- Notices for installation Important Notices 1. The unit installation work must be done by qualified personnel according to the local rules and this manual. 2. If the air conditioner has not plug, directly connect it into the fixed circuit, a breaker should be installed in the fixed circuit. all pole of this breaker should be switching off and the distance of the contact should be at least 3mm.
Notices for installation Safety Requirements For Electric Appliances 1. The power supply should be used the rated voltage and AC exclusive circuit, the power cable diameter should be satisfied. 2．Don't drag the power cable emphatically. 3． It should be reliably earthed, and it should be connected to the special earth device, the installation work should be operated by the professional.
Installation dimension diagram Installation dimension diagram 15 cm Space to the ceiling Above 15cm Above 15cm Above Space to the wall Space to the wall 300 cm Above Air outlet side 2５0 2 cm Above Space to the floor １８
Install indoor unit Install the rear panel 1.Always mount the rear panel horizontally. As the water drainage pipe at the left, when adjusting the rear panel, this side should not be too high; the right side should be slightly high. 2. Fix the rear panel on the selected location. Wall 3. Be sure that the rear panel has been fixed firmly enough to withstand the weight of an adult of 60kg, furthermore, the weight should be evenly shared by each screw.
Install indoor unit NOTE: When connecting the electric wire if the wire length is not enough, please contact with the authorized service shop to buy a exclusive electric wire that is long enough and the joint on the wire are not allowed. The electric wiring must be correctly connected, wrong connection may cause spare parts malfunction. ● Tighten the terminal screw in order to prevent loose. ● After tighten the screw, slightly pull the wire and confirm whether is it firm or not.
Check after installation and test operation Check after installation Items to be checked Possible malfunction Has it been fixed firmly? The unit may drop, shake or emit noise. Have you done the refrigerant leakage test? It may cause insufficient cooling(heating) capacity. Is heat insulation sufficient? It may cause condensation and dripping. Is water drainage well? It may cause condensation and dripping.
Installation and Maintenance of Healthy Filter Installation Instructions 1. Forcibly pull the panel for a specific angle from the two ends of the front panel according to the arrow direction. Then pull the air filter downwards to remove it. (See Fig.a) Fig. a 2. Mount the healthy filter onto the air filter,(as shown in Fig.b). If the air filter cannot be installed, please mount the healthy filter on the front case. (as shown in Fig.c). Fig. b Air filter Healthy filter Healthy filter Fig. c 3.
