OAK Hand Dryer By Alpine OWNER’S MANUAL
INTRODUCTION Thank you for purchasing the Alpine OAK hand dryer! This high-velocity hand dryer is extremely compact and dries hands in seconds. It was specifically designed and built for use in industrial settings and commercial offices. An onboard infrared sensor detects hands and automatically turns the dryer on. The Oak hand dryer also incorporates a replaceable, High Efficiency Particulate Air (HEPA) filter, as well as a reusable air intake pre-filter.
PARTS LIST 1 – Dryer 1 – Replaceable HEPA Air Filter 6 - Wall Screws 6 - Anchor Plugs 1 - Installation Template 1 – Cleaning Brush Note: Typical metal screws have been included with this product. These screws can be used in conjunction with the anchors for most types of walls and studs. However, other screw types may be needed such as: for masonry walls with tiles - use a carbide-tip drill bit; for wood - use wood screws.
INSTALLATION CAUTION: Make sure that no electrical wiring or pipe runs are located in the wall cavity where the dryer is to be installed. If installing the hard-wired option, de-energize all electrical lines before installation begins. 1. Remove all packing material (recycling is recommended). 2. Carefully remove the hand dryer from the shipping carton - be careful not to drop the appliance. 3. Inspect carefully for any damage that may have occurred during transit. 4.
10 5/8"(270MM) (7 2 3 0M /4 M" ) 7 ) MM 4 8 "(1 1/4 26 11/32"(669MM) 11 4 7/64 "(29 8MM )
INSTALLING DRYER 1. Select a wall location height that allows user hand’s to easily find the dryer’s slot Recommended installation heights measured from floor To top of machine To bottom of machine Male Female Child or Disabled 41 13.5 38 10.5 34 6.5 2. Find a stud in the wall using the stud finder. 3. Position mounting template with one set of vertical holes positioned over the stud. 4. Mark hole locations with the pencil. 5. Drill holes in the markings and insert anchors. 6.
INSTALLING DRYER WITH HARD-WIRED OPTION CAUTION: The hard-wire version should only be installed by a certified and trained electrician. 1. Follow steps 1-5 above. 2. Remove the power supply kit cover located on the lower, rear corner of the hand dryer. 3. Remove the existing cord by removing its wires from the dryer terminals. 4. Connect the hard-wired cord’s live wire (+) to the connection terminal marked “L”. 5. Connect neutral wire to the connection terminal marked “N”. 6.
USING THE DRYER 1. Insert hands into slot until the dryer turns on. 2. Move hands up and down in streams of air until dry. 3. Remove hands from slot (the dyer will automatically shut off). ROUTINE MAINTENANCE CAUTION: Failure to maintain filters can cause overheating, damage the dryer and void the warranty. 1. Regularly check pre-filter and HEPA filters for signs of dust and debris (high traffic may require frequent checking). 2.
TROUBLE SHOOTING DRYER FAILS TO START Check power supply is turned on and the power switch on hand dryer is on. Check for foreign objects in the drying cavity that maybe blocking the sensors. Insert hands a little further into the drying cavity to active sensors. HAND DRYER TURNS ON AND OFF ERRATICALLY Clean sensor area inside the drying cavity. NO HOT AIR Check to be sure the temperature switch is set to HOT. Check ambient temperature - the heater will not turn on if temperature is more than 77oF (25oC).
TROUBLE SHOOTING DRYER FAILS TO START Check power supply is turned on and the power switch on hand dryer is on. Check for foreign objects in the drying cavity that maybe blocking the sensors. Insert hands a little further into the drying cavity to active sensors. HAND DRYER TURNS ON AND OFF ERRATICALLY Clean sensor area inside the drying cavity. NO HOT AIR Check to be sure the temperature switch is set to HOT. Check ambient temperature - the heater will not turn on if temperature is more than 77oF (25oC).
LIMITED WARRANTY 1. Alpine (the “Company”) warrants to the original consumer (the “Purchaser’) of any Hand Dryer against any damage caused by attempted burglary for a period of five (5) years from the date of purchase. 2. The Company warrants to the purchaser that the Hand Dryer will be free from defects in workmanship and materials for a period of one (1) year from the date of purchase. 3. These warranties are not assignable or transferable to any other person. 4.
DISCLAIMER Alpine does not guarantee that our products will absolutely stop theft, vandalism, burglary, or acts of God. Our products are only a DETERRENT to such acts. Alpine will always do its utmost to stay current on the prevention of theft and burglary and will continue to offer the best products possible to help in the prevention of such crimes.
Alpine Industries 27 Selvage St Irvington NJ 07111 Info@alpinecorp.net www.alpinecorp.
