Operation Manual

9-EN
4 Make sure that the  indicator light goes out, then
press the preset button in which your desired RDS station
is preset.
If the preset station’s signal is weak, the unit automatically
searches and tunes to a stronger station in the AF (Alternative
Frequencies) list.
5 If the preset station and the stations in the AF list cannot
be received:
When the PI SEEK setting is on (refer to “PI SEEK Setting” on
page 9), the unit searches again for a station in the PI
(Programme Identification) list.
If there are still no stations receivable in the area, the unit
displays the frequency of the preset station and the preset
number disappears.
If the signal level of the Regional (Local) station being tuned
becomes too weak to receive, press the same preset button to
tune in a Regional station in other district.
Notes
• For presetting the RDS stations, refer to the Radio Operation section.
The RDS stations can be preset in the F1, F2 and F3 bands only.
• Operate the unit while the  indicator lights up. If no operation is
performed for 10 seconds, the  indicator goes out.
Receiving RDS Regional (Local) Stations
1 Press and hold FUNC.SETUP for at least 2 seconds to
activate the SETUP mode.
2 Turn the Rotary encoder to select the REGIONAL mode,
and then press ENT.
3 Turn the Rotary encoder to select ON or OFF.
In the OFF mode, the unit automatically keeps receiving the
related local RDS station.
4 Press and hold FUNC.SETUP for at least 2 seconds to
return to normal mode.
Notes
•Press SOUND to return to the previous mode.
• If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
PI SEEK Setting
1 Press and hold FUNC.SETUP for at least 2 seconds to
activate the SETUP mode.
2 Turn the Rotary encoder to select the PI SEEK mode, and
then press ENT.
3 Turn the Rotary encoder to select ON or OFF.
4 Press and hold FUNC.SETUP for at least 2 seconds to
return to normal mode.
Notes
•Press SOUND to return to the previous mode.
• If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
Receiving Traffic Information
1 Press and hold BANDTA for at least 2 seconds so that the
“TA” indicator lights up.
2 Press  or  to select your desired traffic information
station.
When a traffic information station is tuned in, the “TP” indicator
lights up.
Traffic information is heard only when it is being broadcast. If
traffic information is not being broadcast, the unit is set in the
standby mode. When a traffic information broadcast begins, the
unit automatically receives it and the display shows “TRF-INFO”
for 5 seconds.
When the traffic information broadcast is over, the unit will
automatically set in the standby mode.
Notes
• If you do not want to listen to the traffic information being received,
lightly press BANDTA to skip that traffic information message. The TA
mode will remain in the ON position to receive the next traffic
information message.
• If the volume level is changed while receiving traffic information, the
changed volume level will be memorized. When traffic information is
received next time, the volume level will be automatically adjusted to
the level memorized.
• In the TA mode, the SEEK tuning selects only the TP stations.
Receiving Traffic Information While Playing
CD or Radio
1 Press and hold BANDTA for at least 2 seconds so that the
“TA” indicator lights up.
2 Press  or  to select a traffic information station if
necessary.
When a traffic information broadcast starts, the unit
automatically mutes the CD player or the regular FM broadcast.
When the traffic information broadcast finishes, the unit
automatically returns to the original source play before the
traffic information broadcast began.
When traffic information stations cannot be received:
In the CD mode:
When the TP signal can no longer be received, the traffic
information station of another frequency will be selected
automatically.
Note
• The receiver is equipped with the EON (Enhanced Other Networks)
function in order to keep track of additional alternate frequencies to
the AF list. The “EON” indicator lights up while an RDS EON station is
being received. If the station being received does not broadcast the
traffic information, the receiver automatically tunes in the related
station that broadcasts the traffic information when it occurs.
3 Press and hold BANDTA for at least 2 seconds to
deactivate the Traffic Information mode.
The “TA” indicator goes out.
Displaying Radio Text
Text messages from a radio station can be displayed.