Owner`s manual

ManualsBrandsAlpine ManualsAutomotiveCDE-HD137BT

Bluetooth

Firmware

Update Manual

Applicable from 2012 products

for Windows 7

CDE-133BT

CDE-135BT

CDE-136BT

CDE-HD137BT

CDE-HD138BT

CDE-W235BT

19145 Gramercy Place, Torrance,

California 90501, U.S.A.

Phone 1-800-ALPINE-1 (1-800-257-4631)

7300 Warden Ave., Suite 203, Markham,

Ontario L3R 9Z6, Canada

Phone 1-800-ALPINE-1 (1-800-257-4631)

Portal de Gamarra 36, Pabellón, Pabellón, 32

01013 Vitoria (Alava)-APDO 133, Spain

Phone 945-283588

Viale C. Colombo 8, 20090 Trezzano

Sul Naviglio (MI), Italy

Phone 02-484781

98, Rue de la Belle Etoile, Z.I. Paris Nord II,

B.P 50016, 95945 Roissy Charles De Gaulle

Cedex, France

Phone 01-48638989

1-7, Yukigaya-Otsukamachi, Ota-ku,

Tokyo 145-0067, JAPAN

Phone: 81(3)5499-4531

Fax: 81(3)5499-4541

Wilhelm-Wagenfeld-Straße 1-3,

80807 München, Germany

Phone 089-32 42 640

Alpine House

Fletchamstead Highway, Coventry CV4 9TW, U.K.

Phone 0870-33 33 763

161-165 Princes Highway,

Hallam Victoria 3803 Australia

Phone 03-8787-1200

Doc. version 1.00

(January 2013)

Summary of content (18 pages)

PAGE 1
Bluetooth® Firmware Update Manual for Windows 7 Applicable from 2012 products CDE-133BT CDE-135BT CDE-136BT CDE-HD137BT CDE-HD138BT CDE-W235BT 1-7, Yukigaya-Otsukamachi, Ota-ku, Tokyo 145-0067, JAPAN Phone: 81(3)5499-4531 Fax: 81(3)5499-4541 161-165 Princes Highway, Hallam Victoria 3803 Australia Phone 03-8787-1200 98, Rue de la Belle Etoile, Z.I. Paris Nord II, B.P 50016, 95945 Roissy Charles De Gaulle Cedex, France Phone 01-48638989 19145 Gramercy Place, Torrance, California 90501, U.S.A.
PAGE 2
Introduction This manual describes the steps required for updating the Head Units Bluetooth firmware. The update improves compatibility with new mobile phones. Read all warnings and steps carefully before performing the update. Requirements • A Windows 7 computer (connected to the Internet) with Bluetooth connectivity. This includes built-in Bluetooth adapters or external USB Bluetooth adapters. • The Bluetooth adapter must support File Transfer Profile (FTP).
PAGE 3
Bluetooth Firmware Update Instructions The Bluetooth firmware update procedure uses a Bluetooth feature known as File Transfer Profile (FTP) to wirelessly transfer the update file from the PC to the Head Unit. This manual described the update process performed using the Windows 7 operating system (Broadcom Bluetooth Stack and Microsoft Bluetooth Enumerator).
PAGE 4
Result: The Head Unit will return to the “HFP” screen (Fig. 2). (Fig. 2) c) Enable Audio Streaming by using the rotary volume to select “AUDIO” > ENTER > “ON” > ENTER (Fig.3). (Fig. 3) Result: The Head Unit will return to the “AUDIO” screen (Fig. 4). (Fig. 4) button one time to return to the setup menu in which “BT IN” is d) Press the displayed (Fig. 5) (Fig. 5) 3 Confirm that the Head Units Bluetooth visible mode is ON. a) Use the rotary volume to select “VISIBLE M” > ENTER (Fig. 6).
PAGE 5
Result: “NO DEV” will be displayed after the device is cleared (Fig 10). (Fig. 10) c) Repeat step 4 to clear any additional devices. 5 Turn the Head Unit OFF then ON by setting the vehicles ignition to the OFF (LOCK) position then back to the Accessory (ACC) position. 6 Power ON the computer. 7 Confirm that the Bluetooth Adapter is turned on or or a plugged into the computer. The Bluetooth icon similar notification should display on the task bar when the adapter is enabled (Fig. 11). (Fig.
PAGE 6
Creating a Bluetooth Connection between the Computer and Head Unit 1 From the Windows 7 desktop select Start > Control Panel (Fig. 12). Click View by then select Category (Fig. 13). (Fig. 13) (Fig. 12) 2 Select Add a device located below the Hardware and Sound Category. (Fig. 14). (Fig. 14) Result: The Add a device window will open and Windows will start looking for devices (Fig. 15).
PAGE 7
3 Select the device named Alpine CD Receiver in the Add a device window (Fig. 15). 3 (Fig. 15) 4 Select Next on the Add a device window to connect to Alpine CD Receiver (Fig. 15). 5 Check the Head Unit display. Result: The Head Unit will momentarily display “PAIRING” followed by “PAIR NO” (Fig. 16). (Fig. 16) 6 Turn the rotary volume to select “PAIR YES” then press ENTER (Fig. 17). (Fig. 17) Result: “CONNECTING” will begin flashing on the Head Unit (Fig. 18). (Fig.
PAGE 8
Select Close on the Add a device window (Fig. 20). (Fig. 20) 9 Return to the Control Panel window then select View devices and printers. If the window was closed select Start > Control Panel > View devices and printers (Fig. 21). (Fig. 21) 10 Right click on the device named Alpine CD Receiver then select Properties (Fig. 22). (Fig. 22) Result: The Alpine CD Receiver Properties window will open (Fig. 23).
PAGE 9
11 Select the Services tab (Fig. 23). (Fig. 23) 12 Confirm that the Headset service is NOT checked and that all other services are checked, as displayed below (Fig. 24). (Fig. 24) 13 Select OK to accept the changes and close Properties window (Fig. 24).
PAGE 10
Updating the Bluetooth Firmware Caution: Do NOT turn off the vehicle or remove power from the Head Unit while the unit is updating. The update will not be performed correctly and the Head Unit may be damaged. 1 Double click Alpine CD Receiver in the Devices and Printers window (Fig. 25). (Fig. 25) Result: The Bluetooth Device Control menu will open (Fig. 26). 2 Click once on Alpine CD Receiver headset icon in the Bluetooth Device Control window (Fig. 26). (Fig.
PAGE 11
3 Open the “update” folder. 4 Go to the Head Unit then press and hold the AUDIO/SETUP button for at least 2 seconds then release. 5 Use the rotary volume to select “BLUETOOTH” > ENTER (Fig 28). ENTER > “FW UPDATE” > (Fig. 28) Result: “UPDATE NO” will display on the Head Unit (Fig. 29). (Fig. 29) 6 Turn the rotary volume to select “UPDATE YES” then press ENTER (Fig. 30). (Fig. 30) Result: “WAITING” will be displayed (Fig. 31). (Fig.
PAGE 12
Note: The copy process will take approximately 30 seconds to complete. Pay attention that the file is copied completely by viewing that the copy progress bar reaches the end as displayed in (Fig. 33). If the update file was NOT copied successfully please refer to Page 12 under the section titled “If the Bluetooth Update Failed”. (Fig. 33) Note: The Bluetooth connection will automatically disconnect after the file transfer is complete. The Head Unit will then enter update mode and begin the update process.
PAGE 13
Confirming that the Update was Successful 1 Go to the Head Unit then press and hold the AUDIO/SETUP button for at least 2 seconds then release. 2 Use the rotary volume to select “BLUETOOTH” > > ENTER (Fig. 34). ENTER > “FW VERSION” (Fig. 34) 3 Confirm that the version displayed is “01.27.00” (Fig. 34). Congratulations! You have successfully updated the Bluetooth firmware! Note: The Head Units Bluetooth visible mode may change to OFF after the firmware update is complete.
PAGE 14
Alternative Update Method Caution: Do NOT turn off the vehicle or remove power from the Head Unit while the unit is updating. The update will not be performed correctly and the product may be damaged. 1 Press the button on the Head Unit to exit update mode. 2 Close all open windows on the computer desktop. 3 From the Windows 7 desktop select Start Select View devices and printers (Fig. 37) > Control Panel (Fig. 36). (Fig. 37) (Fig.
PAGE 15
5 Click once on Alpine CD Receiver headset icon (Fig. 39). (Fig. 39) Result: A window will open contain 2 folders named “recorder” and “update” (Fig. 40). (Fig. 40) 6 Open the “update” folder. 7 Select Disconnect on the Bluetooth Device Control menu (Fig. 41). (Fig. 41) Result: “(Disconnected)” will be displayed below Alpine CD Receiver (Fig. 42). (Fig.
PAGE 16
8 Go to the Head Unit then press and hold AUDIO/SETUP button for at least 2 seconds then release. 9 Use the rotary volume to select “BLUETOOTH” > > ENTER (Fig 43). ENTER > “FW UPDATE” (Fig. 43) Result: “UPDATE NO” will display on the Head Unit (Fig. 44). (Fig. 44) 10 Turn the rotary volume to select “UPDATE YES” and press ENTER (Fig. 45). (Fig. 45) Result: “WAITING” will be displayed (Fig. 46). (Fig. 46) 11 Go to the computer then select Connect on the Bluetooth Device Control menu (Fig. 47).
PAGE 17
12 Open the folder containing the Bluetooth update firmware (named: FC6000S_01-27-00.plf). 13 Drag-and-drop the update firmware file (named: FC6000S_01-27-00.plf) into the “update” folder opened in step 6 (Fig. 49). (Fig. 49) Note: The copy process will take approximately 30 seconds to complete. Pay attention that the file is copied completely by viewing that the copy progress bar reaches the end as displayed in (Fig. 50). (Fig.
PAGE 18
15 Confirm that he Head Unit is displaying “FIRMWARE UPDATED PLEASE PRESS ANY BUTTON”. 16 Press the button on the Head Unit. Result: The Head Unit will return to the last source mode. For example, if the last source prior to the update was Radio then Radio source will display after the button is pressed. If you can view the last source then it’s safe to restart the Head Unit. 17 Close the Bluetooth Device Control menu on the computer.