Owner's Manual
Table Of Contents
- Operating Instructions
- WARNING
- Getting Started
- Radio
- CD/MP3/WMA (CDE-SXM145BT/CDE-143BT only)
- Sound Setting
- Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat
- Audio Setup
- Other Functions
- SETUP
- BLUETOOTH Operation
- Setup Before Using
- BLUETOOTH SETUP
- Setting the BLUETOOTH Connection (BT IN)
- Setting the BLUETOOTH Device
- Setting the Visible Mode
- Setting the BLUETOOTH sound quality
- Setting the caller information display ON/ OFF
- Setting the Phone Book Update
- Changing the Phone book List Order
- Setting the Received Calls automatically (Auto Answer)
- Selecting the output speaker
- Displaying the firmware version
- Updating the firmware
- Hands-Free Phone Control
- About the Hands-Free Phone
- Answering a Call
- Hanging up the Telephone
- Voice Control Operation
- Calling
- Call waiting function
- Preset a number in the Phone Book (Shortcut dial)
- Dialing the preset number
- Adjusting the volume when receiving a Call
- Muting the microphone input quickly (Voice Mute)
- Call Switching Operation
- BLUETOOTH Audio Operation
- Flash Memory (optional)
- iPod/iPhone (optional)
- SiriusXM Satellite Radio Operation (CDE-SXM145BT only)
- Receiving Channels with the SiriusXM Tuner
- SiriusXM Setting (CDE-SXM145BT Only)
- Checking the SiriusXM Radio ID Number
- Storing Channel Presets
- Tuning Channels using Presets
- Storing the desired Artist and Song Alerts
- Tune Scan Function
- Tune Start Function
- Receiving and Tuning to an Alert
- Search Function
- Using Jump Memory and Jump Recall function
- Replay Function
- Parental Lock Function
- Storing iTunes Tagging information
- Changing the Display
- Information
- Installation and Connections
- LIMITED WARRANTY
![](/manual/alpine/cde-sxm145bt/owner-s-manual-english/images/img-37.png)
38-EN
• The CD is being improperly inserted.
– Make sure the CD is being inserted following instructions in the
CD Player Operation section.
Unable to fast forward or backward the CD.
• The CD has been damaged.
– Eject the CD and discard it; using a damaged CD in your unit can
cause damage to the mechanism.
CD playback sound skips due to vibration.
• Improper mounting of the unit.
– Securely re-mount the unit.
• The disc is very dirty.
–Clean the disc.
• The disc has scratches.
– Change the disc.
• The pick-up lens is dirty.
– Do not use a commercially available lens cleaner disc. Consult
your nearest Alpine dealer.
CD playback sound skips without vibration.
• The disc is dirty or scratched.
– Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only).
• Mechanical error
– Press . After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the problem,
consult your nearest Alpine dealer.
CD-R/CD-RW playback not possible.
• Close session (finalisation) has not been performed.
– Perform finalisation and attempt playback again.
MP3/WMA is not played back.
• Writing error occurred. The MP3/WMA format is not compatible.
– Make sure the MP3/WMA has been written in a supported format.
Refer to “About MP3/WMA” on page 13, then rewrite in the
format supported by this device.
The sound is not output from the speakers.
• Unit has no output signal of the internal amplifier.
– POWER IC is switched to “ON”, refer to “Connecting to an
External Amplifier (POWER IC)” on page 17.
iPod does not play and no sound is output.
• The iPod has not been recognised.
– Reset this unit and the iPod. Refer to “Initial System Start-Up” on
page 10. To reset the iPod, refer to the Owner’s Manual of the iPod.
•No CD is inserted.
–Insert a CD.
• Although a disc is inserted, “NO DISC” is displayed and the unit does
not start to play or eject the disc.
– Remove the disc by following these steps:
Press the button again for at least 2 seconds.
If the disc still does not eject, consult your Alpine dealer.
• Mechanism error.
1 Press the button and eject the CD.
If not ejecting, consult your Alpine dealer.
2 When the error indication remains after ejecting, press the
button again.
If the error indication still does not turn off after pressing the
button for a few times, consult your Alpine dealer.
• When “ERROR” is displayed:
If the disc cannot be ejected by pressing , press the RESET button
(Refer to “Initial System Start-Up” on page 10) and press again.
If the disc still cannot be ejected, consult your Alpine dealer.
• A copy-protected WMA file was played back.
– You can only play back non-copy-protected files.
• A sampling rate/bit rate not supported by the unit is used.
– Use a sampling rate/bit rate that is supported by the unit.
• A USB device that is not supported by the unit is connected.
– Connect a USB device that is supported by the unit.
• A Flash Memory Device is not connected.
– Make sure the Flash Memory device is correctly connected and the
cable is not excessively bent.
• No MP3/WMA (file) is stored in the Flash Memory.
– Connect the Flash Memory device after storing songs (files).
• A copy-protected WMA file was played back.
– You can only play back non-copy-protected files.
• A sampling rate/bit rate not supported by the unit is used.
– Use a sampling rate/bit rate that is supported by the unit.
• Text information that is not recognizable by the unit has been input.
– Use a Flash Memory device with input text information that is
supported by the unit.
MP3/WMA
Audio
iPod
Indication for CD Player (CDE-SXM145BT/
CDE-143BT only)
Indication for Flash Memory
NO DEVICE
NO SUPPORT