Owner's Manual
Table Of Contents
- Installation Manual
- Introduction
- Note
- To Ensure Safe Use, Always Follow These Precautions
- Tools Possibly Required (This Will Vary Depending On The Vehicle)
- Accessory List
- Factory Unit Disassembly Process (2007-2010 Only)
- Factory Unit Disassembly Process (2011-2018 Only)
- Glove Box Removal
- Removing B-Pillar Panel
- Removing Rear Right Side Panel
- Spare Tire and Wheel Removal
- Camera & Light Extension Cable Installation
- Bracket Installation
- Wiring Diagram: OEM Head Unit With SGS-CH01 (Sold Seperately)
- Wiring Diagram: OEM Head Unit With ALP-HRN-CAMCH (Sold Seperately)
- Wiring Diagram: Alpine Head Unit Using Direct Connection
- Wiring Diagram: Alpine Head Unit With SGS-CH01 (Sold Separately)
- Wiring Diagram: OEM Head Unit With SGS-CH01 & KCX-C2600B (Sold Separately)
- Wiring Diagram: OEM Head Unit With ALP-HRN-CAMCH & KCX-C2600B (Sold Separately)
- Troubleshooting
- Quick Installation Manual
Jeep Wrangler
HCE-RCAM-WRA
Stealth-Mount Spare Tire Camera
Quick Installation Manual
• Model: Wrangler
• Model Year: 2007-2018
Jeep
Model Year
Wrangler (JK)
2007-2018
Wrangler Unlimited (JK) 2007-2018
* The specified vehicles have been tested and have
met
compatibility
specs
at
the
time
of
testing.
Compatibility
is
not
guaranteed
if
the
manufacturer has
made
production
changes
to
the
listed vehicles above.
Lt.
Warning: Before you begin wiring, remove the ground wire from the negative terminal of the
battery. Failing
to
do so can lead to electric shock, injury or damage to equipment.
Installation
Kit
Parts
• Camera
Bracket
W/HCE-C1100 x 1 •
• Spare Tire
Bracket
x 1
Power & Video Unit x 1
Water Proofing Adhesive Pad x 1
• Retaining Clips x 3
e Heat Shrink Tube x 1
• Camera Extension Cable x 1
• Quick Installation Manual x 1
•
•
•
Water Proofing Pad x 1
Cable Ties-x 5
• Torx
Screw
&
Lock
Washer x 1
~--
e Allen WrenGh x 1
Factory
Unit
Disassembly
(2007-2010
Only)
1) Remove
top
by
releasing 2 rear
clips
on
the
back
of
the
top
panel and then
:;::~~~;~~~~~~~l~~
...
(-~-
pull panel forward. .'
.,--,,,
2)
Release 2
clips
on
the
top
of
the
bottom
panel. This will expose
two
7mm
I I
screws. Remove those.
3)
Release 2 clips on
the
top
of
the
bottom
panel. This will expose
two
7mm
screws. Remove using a
7mm
socket
with
ratchet & extension.
4)
Use panel removal
tool
to
remove dash panel
by
releasing 6
clips
(3
per
side).
5)
Extract
(4)
7
mm
screws and remove
the
factory
radio.
Factory
Unit
Disassembly
(2010-2018
Only)
1) Remove
the
rubber
cover
from
the
top
center
storage area and
extract
(1)
7mm
screw.
2)
Remove
the
knee
cover
panel and
extract
(2)
7mm
screws located
to
the
right and left
sides
of
the
steering wheel column.
3)
Remove
the
window
switch
pod
using a panel removing
tool
and
extract
(1)
7mm
screw.
4)
Remove
the
dash panel.
5)
Extract
(4)
7
mm
screws and remove
the
factory
radio.
6)
Extract
(2)
7
mm
screws from
the
factory
radio
bracket
and remove it.
Glove
Box
Removal
1) Open
the
glove box.
2)
Push inwards
both
left and right sides
to
release
the
glove
box
out.