WARNING This unit will not power up until the Power Plate is installed .
ALPINE HALO11 11-INCH AUDIO/VIDEO RECEIVER iLX-F411 EN FR ALPINE HALO9 9-INCH AUDIO/VIDEO RECEIVER iLX-F409 • OWNER’S MANUAL Please read before using this equipment. • MODE D’EMPLOI Veuillez lire avant d’utiliser cet appareil. ES • MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. Thank you for purchasing this Alpine product. Please take a moment to protect your purchase by registering your product now at the following address: www.alpine-usa.com/registration.
Contents Operating Instructions PRECAUTIONS IMPORTANT INFORMATION ........................ 5 WARNING Points to Observe for Safe Usage ........................ 5 WARNING ...................................................... 5 CAUTION ....................................................... 6 NOTICE .......................................................... 7 Getting Started Location of Controls ............................................. 9 Turning Power On or Off ....................................
Mute Setting ......................................................... 19 Sound Setup Setting the Media Xpander (MX) ..................... 19 Shuffle Play ........................................................... 28 Searching for a Desired Song ............................. 28 USB Video Equalizer Settings ................................................ 20 Setting the Brightness and Contrast ................. 28 Fader/Balance/Bass/Treble/Subwoofer Settings .............................................
Making a phone call using the Phone Menu ............................................................. 36 Using Voice Recognition function ................... 37 Using Siri .......................................................... 37 Voice Dial Function ........................................ 37 Phone Operation Screen .................................... 38 Adjusting the Speech Volume ....................... 38 Changing the Voice Output ........................... 38 Muting the Microphone ................
Operating Instructions PRECAUTIONS IMPORTANT INFORMATION FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide more reasonable protection against harmful interference in a residential installation, and are more stringent than “outdoor” requirements.
KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately. USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. CAUTION This symbol means important instructions. Failure to heed them can result in injury or material property damage. Failure to do so may result in fire or electric shock. DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to build up inside and may result in fire.
NOTICE Product Cleaning Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic. Temperature Be sure the temperature inside the vehicle is between +45°C (+113°F) and 0°C (+32°F) before turning your unit on. Maintenance If you have problems, do not attempt to repair the unit yourself.
• Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. • Apple, iPhone, and Siri are trademarks of Apple Inc., registered in the U.S. and other countries. Apple CarPlay is a trademark of Apple Inc.
Getting Started Turning Power On or Off When the ignition key is turned to ACC or ON, the opening screen will be automatically displayed. Location of Controls 1 2 Turn the ignition key to the ACC or ON position. The unit turns on. • When the unit is used for the first time, the Radio main screen is displayed. • When turned on, the unit displays the last screen that was displayed before the ignition key was turned off.
Lowering Volume Quickly Switching Sources Audio Mute function instantly lowers the volume level to 0. 1 Touch the 2 Touch a widget of your desired source. 1 2 Touch the (MUTE) button to activate MUTE mode. (HOME) button. The HOME screen is displayed. The audio level will be 0. Touch the (MUTE) button again to bring the audio back to previous volume level. Touch Screen Operation You can operate the unit by using the touch panel display.
Adding a widget About the HOME Screen Drag and drop a widget from the additional candidate widgets area to the desired position of the HOME screen image area. • To show more candidate widgets, swipe horizontally. • There are 3 sizes of widgets. In the HOME screen, select a widget to perform various settings and operations of the function. Touch the (HOME) button. Changing the order of widget The HOME screen is displayed. • You can also display the HOME screen by touching [ the screen.
General Setup Setup [General] is selected on the Settings menu screen. General Setup Menu screen Setup Operation To display the Setup Menu screen: Your vehicle must be parked with the ignition key in the ACC or ON position. To do this, follow the procedures below. 1 Bring your vehicle to a complete stop at a safe location. Engage the parking brake. 2 Release the parking brake. (For safety, release the parking brake while depressing the foot brake pedal). 3 Engage the parking brake again.
Setting the TUNER (FM) Frequency Step During manual tuning, you can select the frequency step for FM analog radio station searching. Setting item: FM Frequency Step Setting contents: 100 kHz / 200 kHz (Initial setting) SiriusXM Setup [Sirius XM] is selected on the General Setup Menu screen. 5 Use the keypad to enter the current (old) 4-digit passcode, and then touch [OK]. The initial passcode is set to “0000.” • Touch [ ] to delete an entered number. 6 7 8 9 Touch [OK] to confirm the entry.
Wallpaper Setup Screen/LED Customize Setup [Wallpaper And Theme] is selected on the General Setup Menu screen. You can change the wallpaper of the display screen from 4 different colored default images or your image. [Screen/LED Customize] is selected on the General Setup Menu screen. Setting item: Dimmer / Screen Dimmer Level / Key Illumination Level Setting a Wallpaper using a default image Setting contents: Amber / Blue / Green / Red Touch the desired image, and then touch [Set Wallpaper].
Displaying the Product Information Clock Setup [Clock] is selected on the General Setup Menu screen. You can set the current time and the clock display type, 12-hour or 24hour, depending on your preference. You can view the version information of this product. Make note of this information and refer to it whenever you contact Alpine Tech Support or an Alpine-authorized dealer. Setting item: Version Information Setting contents: Serial No.
Rear Seat Entertainment (RSE) setup iDatalink Setting [Rear Seat Entertainment (RSE)] is selected on the General Setup Menu screen. [iDatalink] is selected on the General Setup Menu screen. Setting items: Output (page 16) Format (page 16) Rear Seat Entertainment (RSE) Output Setting When a Rear monitor equipped with HDMI input is connected to this unit, change this setting to “On.” You can output images to the Rear monitor.
Connection (Bluetooth) Setup [Connection] is selected on the Setup menu screen. Connection Setup Menu screen • If a 6 character Passkey appears on this device, make sure the same passkey is displayed on the Bluetooth compatible device and touch [OK]. • If all 5 devices have been registered, you cannot register a 6th device. To register another device, you need to delete one of the other 5 devices first.
Camera Setup [Camera] is selected on the Setup Menu screen. You can set up items related to the Camera. Camera Setup Menu screen Rear Camera Guide Settings [Parking Guide Adjust] is selected on the Camera Setup Menu screen. You can adjust the camera guide position. Setting item: Parking Guide Adjust 1 Touch [Parking Guide Adjust] on the Camera Setup menu screen. The camera guide adjustment screen is displayed.
Sound Setup Camera Picture Quality Setup [Sound] is selected on the Settings menu screen. You can set up items related to the sound quality. [Visual Adjust] is selected on the Camera Setup Menu screen. You can adjust the picture quality for the primary and secondary cameras. Sound Setup Menu screen Setting item: Visual Adjust Setting items: Media Xpander (page 19) EQ Presets (page 20) Fader/Balance/Base/Treble/SubW.
Adjusting the Bass/Treble Equalizer Settings Touch [ ] or [ ] for each item to be adjusted. [EQ Presets] is selected on the Sound Setup Menu screen. 10 typical equalizer settings are preset at the factory for a variety of musical source material. Setting item: Bass, Treble Setting contents: -10 to 10 (Initial setting: 0) Setting the Subwoofer Adjusting the Subwoofer Level Setting item: Sub W.
5 To store the adjusted setting value, touch and hold [Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds. • Settings exceeding the frequency of adjacent bands are not available. • While adjusting the Graphic EQ, you should consider the frequency response of the connected speakers. • When the Graphic EQ is adjusted, the Equalizer Presets are overridden. • When Equalizer Presets is set, the linked Graphic EQ settings are also changed.
Volume Setup [Volume] is selected on the Sound Setup menu screen. Setting the Volume for Apple CarPlay When an iPhone 5s or later is connected, touch [Apple CarPlay Volume] to set the volume for Apple CarPlay mode. Setting Item: Media **Offset Setting contents: 0 to 11 (Initial setting: 5) Setting Item: Notification Setting contents: 0 to 35 (Initial setting: 12) • Settable source differs depending on the connected device and settings.
About the Crossover About Time Correction Crossover (X-Over): The distance between the listener and the speakers in a car vary widely due to the complex speaker placement. This difference in the distances from the speakers to the listener creates a shift in the sounds image and frequency characteristics. This is caused by the time delay between the sound reaching the listener’s right versus the left ear. To correct this, this unit is able to delay the audio signal to the speakers closest to the listener.
Example 2. Listening Position: All Seats Adjust the time correction level of each speaker to almost the same level. 1 2 Sit in the listening position (driver’s seat, etc.) and measure the distance (in meters) between your head and the various speakers. Calculate the difference between the distance correction value to the farthest speaker and the other speakers. L = (distance to farthest speaker) – (distance to other speakers) These values are the time correction values for the different speakers.
Apple CarPlay (Optional) Apple CarPlay is a smarter, safer way to use your iPhone in the car. Apple CarPlay takes the things you want to do with your iPhone while driving and puts them right on the unit. You can get directions, make calls, send and receive messages, and listen to music, all in a way that allows you to stay focused on the road. Just plug in your iPhone to the unit and go. • Before using this function, plug in your iPhone using Lightning to USB Cable (Supplied with iPhone) to the unit.
Radio Presetting Stations Manually There are 3 types of [Radio] widgets for the HOME screen. Radio main screen example 1 2 Tune in a desired radio station you wish to store in the preset memory by manual or automatic seek tuning. Touch and hold the Preset number you want to store for at least 1 second. The selected station is stored. 3 Repeat the procedure to store up to 5 other stations onto the same band.
USB Flash drive (Optional) Playback 1 Touch the mode. (HOME) button and select USB Audio The display shows the USB Audio mode screen. You can play back music files (MP3/WMA/AAC/FLAC/WAV), video files (MP4/AVI/WMV/MOV) and photo files (JPG/PNG/BMP) stored in a USB flash drive on the internal player of this system. WARNING It is dangerous for the driver to watch video while driving the vehicle. The driver may be distracted from looking ahead and an accident could occur.
Shuffle Play Touch [ Folder Song OFF ] to select Shuffle Play mode. : A Folder is selected randomly and songs in the Folder are played back in order. After all songs are played in a Folder, the next Folder is selected randomly. : All songs in the Folder (Folder/File) including the song currently being played are played back in random sequence. : Shuffle mode is Off. • If you select a track by using the search mode, the Shuffle mode will be canceled.
USB Photo Slide Show The Slide Show shows photos that change every 3 seconds. USB Photo mode Preview screen Touch [Play]. • To stop the Slide Show, touch the screen. Setting the Effect for Playback You can set the playback effect how switches to the photo for Slide Show. Touch [Effect], and then select the desired effect. Setting the Time Interval for Slide Show You can set the time interval to switch to the next photo. Touch [Time Interval], and then select the desired time interval.
iPod mode on iPhone (Optional) A separately sold Lightning to USB cable (KCU-471i), etc., is required. • This unit does not support video playback from iPhone which connected to this unit via USB Connector. • Internet or telephone function, etc., of the iPhone is not controllable from the unit, but these functions can be controlled using the iPhone itself. • Before operating iPod mode on iPhone, set “Apple CarPlay” to [Off] (page 17).
Searching for a Music File Shuffle Play An iPhone can contain thousands of songs. For this reason, this unit can make various searches using the search function as shown below. Using the Playlist/Artist/Album/Podcast/Audiobook/Genre/ Composer/Song/Radio search mode’s individual hierarchy, you can narrow down your search as shown in the table below.
HDMI Device (Optional) Devices supporting HDMI can connect and play back through this unit (for example, an optional DVD Player, iPhone or other Smartphones). • The HDMI/MHL connecting cable differs depending on the connected device corresponding to HDMI. Prepare optional HDMI/MHL connecting cable sets suitable for your device. HDMI Operation iPhone, Smartphone, etc. The output of your electronic device will be mirrored on this unit through the HDMI connector. Control from this unit is not possible.
SiriusXM Satellite Radio Operation (Optional) SiriusXM Tuner operation: When an optional SiriusXM Tuner is connected to this unit, the following operations may be performed. SiriusXM main screen example (Song Info. Mode) Receiving Channels with the SiriusXM Tuner About SiriusXM Satellite Radio Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment.
No./Song Title Name Changing the Display Text information, such as the channel name, artist name/feature, and song/program title, is available with SiriusXM. The unit can display this text information as explained below. Touch [Info]. Each time you touch this button, the Channel Info. mode and the Song Info. mode switch alternately. For displayed contents, see “SiriusXM main screen example (Song Info. Mode)” (page 33).
Bluetooth Operation Setup Before Using About Bluetooth Bluetooth is a wireless technology allowing communication between a mobile device or personal computer over short distances. This enables a hands-free call or data transmission between Bluetooth compatible devices. Bluetooth transmission is available in the unlicensed 2.4 GHz spectrum if the distance between devices is within 10 meters. For details, refer to the Bluetooth website (http://www.bluetooth.com/).
Use to type a phone number. Calling Phone Book* You can make a phone call from the Phone Book, or edit the Phone Book. Redial Making a phone call using the Phone Menu Dials to the last called number. * If the Hands-Free Phone is not connected, the Bluetooth Setup screen will be displayed. See “Connection (Bluetooth) Setup” (page 17). Making a phone call from the Recent Events list 1 Select a category from [Favorite], [Dialed], [Received] or [Missed] on the Phone menu.
3 Touch [ 4 Touch [Call]. ] (Call). A confirmation message of the phone number appears. The phone call is started. Calling in Private When using the Private Call setting, the conversation is not output through the speaker. Voice Dial Function You can make a telephone call by using voice operation. • Connect your smartphone to the unit via Bluetooth, then set to “Handsfree” (page 17). 1 Touch [ ] button. Touch [ ] during the call.
Phone Operation Screen Phone Book Function Phone Book screen example Name and phone number • If it is registered with a Group, the Group Name is also displayed. Although, depending on the connected mobile phone, it may not be displayed. Conversation time You can make a call using the phone book search function. 1 Adjusting the Speech Volume You can adjust Caller Level and Microphone Level. Touch [ ] or [ ] of “Speaker Volume ( ( )”.
Deleting the Phone Book Entries Deleting One Entry from the Phone Book Touch [ ] of the contact name (or phone number) you want to delete. The selected number is deleted. Bluetooth Audio If a Bluetooth compatible mobile phone, portable player, etc. is connected by wireless, you can play back a song (operation is controllable from the unit). • Operation may vary, depending on the Bluetooth compatible device.
Playback Connecting a Bluetooth Device 1 Registering a Bluetooth device in the unit enables automatic connection. If it does not connect automatically, run through the connection procedure again. Touch the (HOME) button and select Bluetooth Audio mode. The display shows the Bluetooth Audio mode screen. 2 Touch [Reconnect] on the Bluetooth Audio screen. Touch [ ] or [ ] to select the desired track (file). The Bluetooth connection will start.
Camera Operation (Optional) When an optional camera is connected, the view video of camera can be output to the monitor. Rear camera: If a rear camera is connected, when the vehicle is reversed, the rear camera view (guide marks for vehicle width and available distance) is displayed automatically on the screen of this unit. About the Rear Camera Guide To display the guide, set “Turning the Rear Camera Guide On/Off ” (page 18) to On. Also, to adjust the guide, see “Rear Camera Guide Settings” (page 18).
Distance guidance mark Actual distances The distance guides represent the ground level distance from the rear bumper. It is difficult to accurately estimate the distance to objects above ground level. In the following example, the distance to A is 0.5 m and the distance to B is 1 m. Error Error C B A (about 0.5 m) The distance guidance mark represents the distance to a flat road surface.
iDataLink Operation Gauges screen example You can check the vehicle’s speed, the engine’s rotation speed, etc. When the unit is connected to the car’s iDataLink module, you can transfer and receive data between the car and the unit to check the car’s status, or to make various operations from the unit. • An iDataLink module (sold separately) is required. • Available functions differ depending on your vehicle. For details, refer to your vehicle’s instruction manual.
About Parking Sensor screen Factory Media Operation The Parking sensor screen turns on when the front or rear sensor on your vehicle detects an obstacle within a certain distance. You can operate the Factory Audio (USB/iPod/Bluetooth Audio) from this unit. Parking Sensor Full screen example When the front or rear sensor detects an obstacle within a certain distance, the Parking Sensor screen is displayed, and the indicator ( ) that corresponds with that area lights up.
Information Product Software Update This product use software that can be updated through a USB flash drive. Download the software from the Alpine website and update the product using the USB flash drive. Updating this product Check the Alpine website for details on updating. http://www.alpine-usa.com Important information on the software About the software license of the product The software installed in the product contains open-source software.
Corresponding File Systems Terminology This device supports FAT 16/32. The maximum nested folder depth is 8 (including the root directory). File names are limited to 256 characters (including the extension). Valid characters for folder/file names are letters A-Z (all caps), numbers 0-9, and ‘_’ (underscore). Order of files Files are played back in the order that the writing software writes them to the disc. Therefore, the playback order may not be what’s expected.
In Case of Difficulty If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected, or then consult your authorized Alpine dealer. Basic No function or display. • Vehicle’s ignition is off.
If this Message Appears Various messages are displayed on the screen during operation. In addition to the messages telling you the current status or providing guidance for the next operation, there are also the following error messages. If one of these error messages is displayed, carefully follow the instructions in the solution column. System This operation is prohibited for your safety. • A setup operation, etc., was carried out while the vehicle was running.
Bluetooth SECTION Specifications Bluetooth Specification Output Power Profile MONITOR SECTION Screen Size 11” (iLX-F411) 9” (iLX-F409) LCD Type Transparent type TN LCD Operation System TFT active matrix Number of Picture Elements 1,152,000 pcs.
LIMITED WARRANTY ALPINE ELECTRONICS OF AMERICA, INC. (“Alpine”), is dedicated to quality craftsmanship and is pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below. PRODUCTS COVERED: This Warranty covers Car Audio Products and Related Accessories (“the product”). Products purchased in the Canada are covered only in the Canada. Products purchased in the U.S.A.
About the Rules of Bluetooth Electromagnetic Radiation Regulation USA/Canada FCC/IC CAUTION This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
ff#HILPINE ALPINE HALO11 11-INCH AUDIO/VIDEO RECEIVER iLX-F411 ALPINE HALO9 9-INCH AUDIO/VIDEO RECEIVER iLX-F409 • INSTALLATION MANUAL • GUIDE D'INSTALLATION • MANUAL DE INSTALACION ALPINE ELECTRONICS MARKETING, INC. ALPINE ELECTRONICS GmbH ALPINE ITALIA S.p.A.
ENGLISH Contents WARNING ..................................•.........•...•..... 2 CAUTION ....................•......................•.•.•....... 2 Precautions ................................................... 3 Accessory List 3 Installation .............................................................. 3 Caution concerning the installation location ............................................................ 3 Adjust the front-back position of the Display unit (Optional) ............................
Lh WARNING DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. This symbol means important instructions. Failure to heed them can result in serious injury or death. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc. DO NOT DISASSEMBLE OR ALTER.
Precautions • Be sure to disconnect the cable from the (-) battery post before installing your unit. This will reduce any chance of damage to the unit in case of a short-circuit. • Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system. • When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer).
Adjust the front-back position of the Display unit (Optional) 3 Tightly fix the slider using the 4 screws that were removed in Step 1. Flush head screw Depending on the vehicle, it may be necessary to adjust the frontback position of the Display unit when mounting it. If front-back position adjustment is necessary, set the slider to the back position before mounting the display unit to the vehicle. [Default setting: forward position) & WARNING MAGNETIC SCREWDRIVER REQUIRED TO CAREFULLY REMOVE SCREWS.
Installation example using the Original Mounting Bracket 1 Mount the original mounting bracket to the main unit using the supplied screws. Install the display unit 1 Remove the 2 angle adjustment screws (M4x6) fixing the left and right sides of the Display unit and pull the top of the display forward. Ifyou do not have the original mounting bracket, mount the Double din KIT" (provided with the side m ounting bracket), etc. to the main unit. * Sold separately.
2 Fix the Display unit to the slider of the main unit using 4 screws (M4x6). 4 Adjust the mounting position of the display. • The available adjustment positions of the Display differ depending on the front-back/up-down/angle positions. Consult "Position Adjustment and Mounting Dimensions of the Display" (page 17) for details. 1) Hold the Display up vertically, remove the 4 flush head screws (M4x l 3) on the left and right sides for up-down adjustment, and adjust the up-down position of the display.
2) After adjustment, tightly fix the display with the 4 Flush head screws (M4x13) for up-down adjustment. Refer to the Illustration below to use the screw holes for angle adjustment. • Example: To install the display at the angle of 20°, use the screw holes 2 andb. o• L -20~ [ 45° Flush head screw(M4x13) (left and right) 3) Adjust the angle of the display.
S Attach Cover rear-L/R to the left and right sides of the display unit. Cover rear L (included) Cover rear R (included) When removing Cover rear-L!R, push in the tab and slide it.
Connections J7 Vehicle Antenna CD ~------------Microphone (included) USB extension cable (included) To USB flash drive, iPhone or Android smartphone. REMO (Blue/White) @ REVERSE (Orange/White) @ P. ANT (Blue) @ PARKING BRAKE (Yellow/Blue) ® ACC (Red) ® BATT (Yellow) GND (Black) To amplifier or equalizer To plus side of the back lamp signal lead of the car ~ To power antenna - - To the parking brake signal lead lgnitio-n key CV @ @ e Battery ~ t ~~ FlJ I [/ij rl I I \ ...l.
CD Radio Antenna Receptacle ® @ Remote Turn-On Lead (Blue/White) Connect this lead to the remote turn-on lead of your amplifier or signal processor. ® Connect this lead to the +B terminal of your power antenna, if applicable. • This lead should be used only for controlling the vehicle's power antenna. Do not use this lead to turn on an amplifier or a signal processor, etc.
If an ACC power supply is not available Connection Diagram of SPST Switch (sold separately) ACC (Red) ILX-F411 /iLX-F409 I- ------7 : --------- --BATTERY : - - --------------, FUSE (SA) 1 SPST SW (Optional) : (Optional) - ----------------- (Yellow) - FUSE(20A) (Optional) CJ e (±) Battery rm • Ifyour vehicle has no ACC power supply, add an SPST (single-pole, single-throw) switch (sold separately) and fuse (sold separately).
System Example Connection of an iPhone ■ When connecting to an iPhone with a Lightning connector iPhone with a Lightning connector (sold separately) use connector D @ -- ~ 1re '-'====t~c::[J=====tl1======::c:/ USB extension cable (included) Lightning to USB Cable KCU-471 i (sold separately) • Do not leave an iPhone in a vehicle for a long time. Heat and humidity may damage the iPhone, and you may not be able to play it again.
Connection of an HDMI Device (iPhone with a Lightning connector) HDMI input connector' iPhone with a Lightning connector (sold separately) USB connector D USB extension cable (Included) Lightning to USB Cable KCU-471 i (sold separately) (!====tll~Jl (- ----------i::::=rJ HDMI connection kit KCU-61 OHO (sold separately) Lightning Digital AV Adapter (Apple Inc., products) (sold separately) * W hen connecting an HDMI connection cable, be sure to secure it using the supplied HDMI Fixation Bracket.
Connection of an HDMI Device (Android device) use connector HDMI Input connector• Android device with HDMI connector (sold separately) ~ D w ■ USB extension :able (Included) HDMI connection kit KCU-610HD (sold separately) □ Micro USB conversion cable :,11~ r -- - - - 1 • CO:---•:•---i--- n HDMI connection cable HDMI Type-D conversion adapter Android device with MHL connector (sold separately) ■ MHL connection kit KCU-610MH (sold separately) Micro USB conversion cable ".;;,.
Connection of an External Am_e_lifier I ~@~ ED/•~+~ CAMERA/PRE OUT Power Supply Connector REMOTE ON Connector REMO (Blue/White) ® (Blue/White) REMOTE ON (Blue/White) Power cable (Red) PRE OUT cable ~ ~ I ~ ~ (White) (Red) To front Input terminal (White) (Red) ~~ @ Remote Turn-On Lead (Blue/White) @) Subwoofer RCA Connectors ® ® Front Output RCA Connectors Subwoofer To subwoofer Input terminal ~~ (White) Amplifier for subwoofer (soldseparately) Front speaker Amplifier4ch (sold se
Connection of a Rearview camera Emjj ®~~ .... EO CAMERA/PRE ou{ Connector f f Power Supply Connector Power cable Reverse @ Connect to the plus side of the car's reverse lamp. (Orange/White) PRE OUT cable To Video Output terminal @ 0 Camera with RCA video output (sold separately) REAR VIEW CAMERA @ Reverse Lead (Orange/White) 0 RCA Extension Cable (sold separately) @ CAMERA Input RCA Connector • Set the Camera Select to "Rear.
Position Adjustment and Mounting Dimensions of the Display The mounting position of this unit's Display can be adjusted (front-back/up-down/angle). When mounting the Display, confirm the mounting position and mounting dimensions so that it does not obstruct your field of vision or impair driving. ~ WARNING • In the following cases, the display cannot be mounted. It impairs operation of the steering wheel or various levers (gearshift, windshield wiper switch, turn signal switch, etc.
■ Display mounting dimensions and adjustable positions (iLX-F409) Dis~ unit size Front-back _eosition 235.2 mm (MAX) 50mm 70mm 28mm 8mm ' ~ ! E E N ri JI JI ~ Adjustable Display angle and up-down position 45° E E 0 ~ 0 -- - - - E E ~ E E * Depending on the up-down position of the forward and back positions, there are certain positions in which the angle cannot be adjusted.
■ Mounting Dimensions for Angle Adjustment of the Display (iLX-F411) Angle: 45° :mm Angle: 20° Angle: -20° A' flt I A' A A B A A' B B' 123.3 171.5 -8.8 39.5 I A A' B B' A A' B B' 166.7 123.8 -7 58.2 100.2 84.7 11 5.6 -15 mm 152.6 118.7 -21.1 53 86.1 89.9 -3.1 10.7 -30mm 138.5 113.6 -35.2 47.8 72 95 -17 .2 15.8 -45 mm 124.4 108.4 -49.3 42.7 57.9 100.1 -31 .3 21 -60mm 110.3 103.3 -63.3 37.6 43.8 105.3 -45.
■ Mounting Dimensions for Angle Adjustment of the Display (iLX-F409) Angle: 45° :mm Angle: 20° Angle: -20° A' A' A' A A A A' B B' A A' 100.8 1424 -5.3 36.2 134.2 120.1 -30mm -45mm -60mm 77.8 0 -15 mm B B' A A' B' 106.7 -5.3 534 100.2 80 9.3 5.6 101.6 -194 48.3 86.1 85.1 -4.9 10.7 106 964 -33.5 43.1 72 90.3 -18.9 15.8 91.9 91.3 -47.6 38 57.9 95.4 -33 21 86.2 -61.7 32.9 43.8 100.5 -47.1 26.
ff#MLPINE ALPINE HAL011 11-INCH AUDIONIDEO RECEIVER iLX-F411 ALPINE HAL09 9-INCH AUDIONIDEO RECEIVER iLX-F409 Made for • android auto™ 0 Bluetooth® Apple CarPlay {()) ~=:=flac •••• free loHle-ss ~ codec ■ II Works with aiPhone ■ READY H i:J m I TM HIGH-DEFINITION MULTIMEDIA INTERFACE QUICK REFERENCE GUIDE GUIDE DE REFERENCE RAPIDE GUfA DE REFERENCIA R.APIDA Please register your product at www.alpine-usa.com/registration to protect your purchase. Enregistrez-vous sur www.
About the Rules of Bluetooth Electromagnetic Radiation Regulation USA/Canada FCC/IC CAUTION This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Contents WARNING ................................................................................................................................................................ 2 CAUTION .................................................................................................................................................................3 Getting Started .................................................................................................................................................
WARNING ihwARNING USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may result in fire, electric shock or other injury. This symbol means important instructions. Failure to heed them can result in serious injury or death. MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage. INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER CANNOT WATCH TVNIDEO UNLESS THE VEHICLE IS STOPPED AND THE EMERGENCY BRAKE IS APPLIED.
~CAUTION This symbol means important instructions. Failure to heed them can result in injury or material pre>pertydam~ . _ _ _ __ _ _ _ __ HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing. HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience.
Location of Controls, Turning Power On or Off Owner's manual Getting Started Controls Position The screen design used in the Quick Reference Guide may differ from the actual screen. l~'Ti 'tltl~lil iaf G) RESET switch ® - /+(DOWN/UP) button Touch to adjust the volume. @ ~ (MUTE) button Touch to activate/deactivate the mute mode. @ (J) BBB (HOME) button Activates the HOME screen. ~/....ibutton Touch to seek down/up stations in radio mode or down/up a track, chapter, etc.
Turning Power On or Off 1 Turn the ignition key to the ACC or ON position. The system is turned on. • When using the system for the first time, the Radio main screen is displayed. About the HOME Screen Select a widget on the HOME screen to perform various settings and operations of the function. 1 Touch the BBB (HOME) button. The HOME screen is displayed. ■ HOME screen example ••• ••• r'.' .,~ 12·03 ·· · • ,-.1 . , ((i)) n o m ~ , Widget Touch to activate the function.
Editing the HOME screen You can customise widgets displayed on the HOME screen. 1 Touch and hold the HOME screen. The widgets editing screen is displayed. ... ... n 12:04 .:.)) ~ II (('J.)..l; ".i □ II n 0 --· ~ a r: ~. HOME screen image " .. ~ r-- I{:) 0 0 Additional candidate widgets Add your desired widget to the HOME screen. Swipe this area horizontally to show more candidate widgets. • There are 3 sizes of widgets.
Owner's manual Apple CarPlay (Optional) Apple CarPlay Operation (Optional) Apple CarPlay is a smarter, safer way to use your iPhone in the car. Apple CarPlay takes the things you want to do with your iPhone while driving and puts them right on this unit. You can get directions, make calls, send and receive messages, and listen to music, all in a way that allows you to stay focused on the road. Just plug in your iPhone to this unit and go. 1 Touch the ~gg (HOME) button. The HOME screen is displayed.
Owner's manual Radio Radio Operation ... Displays the HOME screen 12:27 PM II Decreases frequency P5 Touch and hold to change the frequency continuously. ■ • 89.9 DX Seek 105.3 95.5 MHz 103.7 A.f,1ec'1C Information display Increases frequency J - 8;;•,,i Touch and hold to change the frequency continuously. Preset button l1 Displays the preset stations with a short touch. Touch for at least 1 second to memorise the current station as a preset station. Changes tuning mode .
Owner's manual SiriusXM Satellite Radio Operation (Optional) SiriusXM Satellite Radio Operation (Optional) When an optional SiriusXM Tuner is connected to th is unit, the following operations may be performed. - - - - - - Signal Indicator Displays the HOME screen ... 2:14 ---•jj.f -- Changes to previous channel Siriusxm -- I Ch001 PM Information display Artist Nmm) l Song Name Album Name Changes to next channel Ch002 Ch003 Ch004 Ch005 Ch006 Q. CI ..
Owner's manual iPod mode on iPhone (Optional) iPod mode on iPhone (Optional} A separately sold Lightning to USB cable (KCU-471 i) is required depending on the type of iPhone.
Owner's manual Bluetooth Setup, Bluetooth Operation - Hands-Free Phone Control The unit can connect with up to two hands-free phones. How to connect to a Bluetooth compatible device (Pairing) To display the Setup HOME screen: 1. Bring your vehicle to a complete stop at a safe location. Engage the parking brake. 2. Release the parking brake. (For safety, release the parking brake while depressing the foot brake pedal). 3. Engage the parking brake again.
Owner's manual_----'" ___ ~ _ Specifications Specifications MONITOR SECTION Bluetooth SECTION Screen Size Bluetooth Specification Output Power Profile 1l"(iLX-F411) 9" (iLX-F409) LCD Type Transparent type TN LCD Operation System TFT active matrix Number of Picture Elements 1,152,000 pcs. (800 x 480 x 3 (RGB)) Effect ive Number of Picture Elements 99%ormore Illumination System LED Bluetooth V4.1 +4 dBm Ave.
• Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. • Apple, iPhone, and Siri are trademarks of Apple Inc., registered in the U.S. and other countries. Apple CarPlay is a trademark of Apple Inc.
~LPINE LIMITED WARRANTY ALPINE ELECTRONICS OF AMERICA, INC. ("Alpine"), is dedicated to quality craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below. e PRODUCTS COVERED: e HOW WE LIMIT IMPLIED WARRANTIES: This Warranty covers Car Audio Products and Related Accessories ("the product").
##HILPINE ALPINE ELECTRONICS MARKETING, INC. ALPINE ELECTRONICS OF U.K., LTD. 1-7, Yukigaya-Otsukamachi, Ota-ku, Tokyo 145-0067, JAPAN Phone: 03-5499-4531 Alpine House Fletchamstead Highway, Coventry CV4 9TW, U.K. www.alpine.co.uk ALPINE ELECTRONICS OF AMERICA, INC. ALPINE ELECTRONICS GmbH Succursale France 1500 Atlantic Blvd, 184 al lee des Erables Auburn Hills, Michigan 48326, U.S.A.
Thank you for choosing Alpine for your car audio equipment needs. Our goal is to produce the best audio/video/navigation products in the world and hope your expectations are met. Please take a moment to protect your purchase by registering your product now at the following address: www.alpine-usa.com/registration. You will be informed of product and software updates (if applicable), special promotions, and news about Alpine.
You can see the detailed manual. Vous pouvez voir le manuel detaille.