Installation Instructions

ManualsBrandsAlpine ManualsCar VideoAlpine 9" Halo9 Plug And Play Dash Kit For 2014-Up Toyota Tundra

Toyota Tundra

iLX-F309TND  1/19

Toyota Tundra

iLX-F309TND

9” Restyle In-Dash System

Installation Manual

 Model: Tundra

 Model Year: 2014-Up

Note

Design and speciﬁcations are subject to change without notice for improvement.

To Ensure Safe Use, Always Follow These Precautions

The installation of this product requires specialized skills and experience. We recommend that you have the

product installed by an Alpine authorized dealer.

Before you use this product, be sure to carefully read this installation manual and the separate user's manual

so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as

a result of failure to follow the instructions in the manuals.

This manual includes a number of symbols that are intended to help you use the product safely, to prevent

harm to you and others, and to protect against damage to property. These symbols and their meanings are

listed below. Make sure you fully understand these symbols before you begin reading the main text.

Explanations of Injury and Damage That May Result from Incorrect Use

Warning

Ignoring the content marked by this indication and using the product incorrectly is

expected to lead to death or serious injury.

Caution

Ignoring the content marked by this indication and using the product incorrectly is only

expected to lead to injury or property damage.

Toyota

Model Year

Tundra 2014 - Up

* The speciﬁed vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is

not guaranteed if the manufacturer has made production changes to the listed vehicles above.

Warning: Before you begin wiring, remove the ground wire from the negative

terminal of the battery. Failing to do so can lead to electric shock, injury or damage

to equipment.

Introduction

Congratulations on purchasing the iLX-F309TND. This installation manual is designed to take you through the

step-by-step installation of iLX-F309TND into a 2014-Up Toyota Tundra. Please familiarize yourself with the

owners manual and if you still have additional questions please call 1-800-TECH-101.

Summary of content (19 pages)

PAGE 1
Toyota Tundra iLX-F309TND 1/19 Toyota Tundra iLX-F309TND 9” Restyle In-Dash System Installation Manual Model: Tundra Model Year: 2014-Up Toyota Model Year Tundra 2014 - Up * The speciﬁed vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is not guaranteed if the manufacturer has made production changes to the listed vehicles above. Warning: Before you begin wiring, remove the ground wire from the negative terminal of the battery.
PAGE 2
Toyota Tundra iLX-F309TND 2/19 Tools Required Panel Removing Tool 10mm Socket Phillips Screwdriver Wire Cutters Extension Ratchet Needle Nose Pliers Flathead Screwdriver Accessory List Installation Kit Parts iLX-F309TND Radio Mounted In Dash Bezel Main Harness With Maestro Module Plugged In OBDII Adapter Cable Bluetooth Mic Phillips Screws x 1 FM Antenna Adapter
PAGE 3
Toyota Tundra iLX-F309TND 3/19 GPS Antenna Adapter Satellite Radio Antenna Adapter OEM USB Adapter Low Level RCA Adapter Cable Ties x 10 USB Extension Harness Aux/Preout Harness Documents Quick Reference Alpine Guide Registration Card
PAGE 4
Toyota Tundra iLX-F309TND 4/19 Programming the iDatalink Maestro Module The Maestro module is pre-flashed already. This page is here in case the module needs to be flashed again. 1 INSTALL THE WEBLINK PLUG-IN Go to: idatalinkmaestro.com/plugin and follow the installation steps. The Maestro module must be programmed specifically for each vehicle and radio. Take care to enter the correct vehicle information, factory options, head unit model, and head unit serial number.
PAGE 5
Toyota Tundra iLX-F309TND 5/19 Factory Unit Disassembly Process 1 Use a panel removal tool to release clips of the cigarette lighter/AUX panel and remove it. 3 Use a 10mm socket to extract (4) 10mm screws below the radio. 5 Use a panel removal tool to release screw cover on the driver’s side A pillar. 2 Use a panel removal tool to release the clips on the HVAC control panel and remove it.
PAGE 6
Toyota Tundra iLX-F309TND 6/19 Factory Unit Disassembly Process (Continued) 7 Use a panel removal tool to release the clips on the door sill and remove it. 8 9 Use a 10mm socket to extract (2) 10mm screws from the driver’s side knee cover panel. 10 Use a panel removal tool to release the clips on the 11Use a panel removal tool to release the rear cover from the eyewear compartment and remove it. Remove the plastic nut on the driver’s kick panel and carefully lift the kick panel to remove it.
PAGE 7
Toyota Tundra iLX-F309TND 7/19 Installation Instructions 1 3 5 Use the included 3mm Phillips screw to mount the microphone next to the eyewear compartment. Note: Be sure to clear the motion path of the sun visor. 2 Route the microphone cable down the driver’s A pillar following the factory harness while securing the cable with the provided cable ties. 4 Route both the microphone and OBD2 cables to the radio cavity as shown below.
PAGE 8
Toyota Tundra iLX-F309TND 8/19 Installation Instructions (Continued) 7 Mount the iLX-F309TND using (2) 10mm factory screws. Note: Place the additional (2) 10mm screws in their respective location in case they are need in future applications. 8 Replace all removed components to their factory location and connect the Negative (-) battery terminal.
PAGE 9
Toyota Tundra iLX-F309TND 9/19 iLX-F309TND Wiring Diagram W/O Factory Amplifier To Vehicle Connectors Rear Speaker 6-pin Connector Rear Power/Speaker 10-pin Connector Rear 28-pin Connector Front 24-pin Connector Front To OBDII Connector Red Not Used Black Not Not Used Used Reset Button 18-Pin Connect to White GPS Antenna Connector Blue/White Amp Turn-on iDatalink MAESTRO Module * Main Harness GPS Antenna Adapter See page 12 for HDMI connection info Camera Adapter iLX-F309 Source Uni
PAGE 10
Toyota Tundra iLX-F309TND 10/19 iLX-F309TND Wiring Diagram With Factory Amplifier To Vehicle Connectors Rear Speaker 6-pin Connector Rear Power/Speaker 10-pin Connector Rear 28-pin Connector Front 24-pin Connector Front To OBDII Connector Red Not Used Black Not Not Used Used Reset Button 18-Pin Connect to White GPS Antenna Connector Blue/White Amp Turn-on iDatalink MAESTRO Module * Main Harness GPS Antenna Adapter See page 12 for HDMI connection info Camera Adapter iLX-F309 Source U
PAGE 11
Toyota Tundra iLX-F309TND 11/19 Connection Of An External Amplifier RCA Extension Cable (sold separately) USB CAN I/F GPS Remote Turn-On Lead (Blue/White) HDMI IN Subwoofer RCA Connectors SXM/DAB Front Output RCA Connectors W.
PAGE 12
Toyota Tundra iLX-F309TND 12/19 iLX-F309TND HDMI Input Do not use the head unit’s USB to power HDMI devices. This port is meant for Apple CarPlay, Android Auto, and USB flash drives. iLX-F309 Source Unit CAN I/F USB GPS HDMI IN SXM/DAB PRE OUT EXT. KEY W.REMOTE POWER ANTENNA iPhone For iPhone the Lightning to HDMI adapter is required For all phones the USB power source needs to be a 2A source. This will require a separate USB power source to be installed in the vehicle.
PAGE 13
Toyota Tundra iLX-F309TND 13/19 iLX-F309TND Wiring Diagram To SiriusXM Tuner Vehicle Antenna GPS Antenna (Included) SPEED SENSOR (Green/White) CAMERA IDATALINK I/F AUX INPUT REMO (Blue/White) Interface cable REVERSE (Orange/White) P.
PAGE 14
Toyota Tundra iLX-F309TND 14/19 Wire Harness Pin Outs Remote Harness Radio Main Blue 22AWG Red 20AWG Blue/White 22AWG Orange/White 22AWG Yellow/Blue 22AWG 8 16 7 15 6 14 5 13 4 12 3 11 2 10 1 9 5 1 1 2 2 3 1 Green 22AWG Green/Black 22AWG 4 3 17 15 13 11 9 7 5 OEM Speaker Harness 2 OEM Speaker Harness 1 6 11 12 9 10 7 8 5 6 3 4 Purple 20AWG Gray 20AWG Purple/Black 20AWG Gray/Black 20AWG Green 20AWG White 20AWG Green/Black 20AWG White/Black 20AWG Yellow 18AWG Black 18AWG Cam Aux Data White
PAGE 15
Toyota Tundra iLX-F309TND 15/19 Adding A Front Camera To use the OEM camera the RCA will need to be extended to the “Other” input on the KCX-C2600B. RCA Camera Input Main Harness iLX-F309 Source Unit CAN I/F USB GPS HDMI IN SXM/DAB KCX-C2600B (Sold Separately) PRE OUT W.REMOTE POWER ANTENNA Reverse Out (Orange/Black) 1 2 3 4 5 6 1 - V.
PAGE 16
Toyota Tundra iLX-F309TND Connection Of KAC-001 (Sold Separately) KAC-001 Side View POWER RESET HEADUNIT CAN OUTPUT GND (Black) *Fuse Rating: 7A 8ch Output Harness (24-pin White) ACC (Red) Interface Cable (4-pin) (included with ADS module) BATT* (Yellow) USB port (Firmware updates only) Interface Harness (4-pin White) Power Harness (3-pin White) Reset Button UPDATE Output 1 (Purple) Output 2 (White/Red) Output 3 (Brown) Output 4 (Blue) Output 5 (Green) Output 6 (Pink) Connect to IDATALINK I/F
PAGE 17
Toyota Tundra iLX-F309TND 17/19 Steering Wheel Configuration Right Up Left Enter Down Back Mode/Hold Off Hook On Hook Voice MODE HOLD Volume Up Volume Down Button Press Once Press And Hold Right Display Guages Screen None Up Seek + Preset & Folder + Left Display Vehicle Screen Info None Enter Phone Menu None Down Seek - Preset & Folder - Back Band None Mode/Hold Source None Volume Up Volume + None Volume Down Volume - Attenuation On/Off Off Hook Answer Call None On
PAGE 18
Toyota Tundra iLX-F309TND 18/19 Set Up Guide 1 2 3 4 5 6 Turn the vehicle’s Ignition switch to ACC. 7 When the KAC-001 (External Accessory Control Module) is present be sure to turn it ON in the SETUP MENU. (MENU/SYSTEM/EXTERNAL ACCESSORIES/EXTERNAL ACCESSORY CTLR). 8 9 Vehicle information- Set the desired gauge information. (MENU/VEHICLE INFO/GAUGES/CAR SETTINGS). Turn ON the iLX-F309TND by pressing any key. Select the user language and press OK.
PAGE 19
Toyota Tundra iLX-F309TND 19/19 Troubleshooting Guide Continued Symptom 4 Possible Cause Remedy Incorrect serial number was used when flashing maestro. Flash Maestro with correct serial number. 4 pin Maestro data cable is disconnected or damaged. Check for proper connection or disconnected pins. OBD2 cable is not plugged in. Connect OBD2 connector to the OBD2 port. Monitor, power plate screw, or main harness are not connected. Check for proper connection or disconnected pins.