IN-DASH GPS NAVIGATION RECEIVER INE-W960 INE-NAV-60 INE-W960S Made for ~ iPod DiPhone iz:? II 0 Bluetooth® [I] ~2Hlv DIVX. ~ Maps for Life !!§.! r--------------------------, : 1()) PANDORA ~ READY l __________________________ j WORKS WITH 1 (INE-W960/INE-NAV-60 only) II II II Alpine Tunelt App QUICK REFERENCE GUIDE GUIDE DE REFERENCE RAPIDE GUfA DE REFERENCIA RAPIDA GUIA DE REFERENCIA RAPIDA Open only to legal US. residents.
Contents WARNING ................................................................................................................................................................2 CAUTION .................................................................................................................................................................2 Getting Started ..................................................................................................................................................
WARNING &wARNING This symbol means important instructions. Failure to heed them can result in serious injury or death. DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE. Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident. KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE REACH OF CHILDREN.
Getting Started Accessory List INE-W960/INE-NAV-60/INE-W960S ............................................ 1 Power cable .............................................................................................. 1 Flush head screw (M5x8) ................................................................ 6 Screw (M5x8) .......................................................................................... 8 GPS Antenna ......................................................................................
Turning Power On or Off 1 Turn the ignition key to the ACC or ON position. The system is turned on. 2 4-EN Press and hold the MUTE button for at least 3 seconds to turn the power off.
Owner's manual Radio/RBDS Radio/RBDS Operation Decreases frequency-----. Radio information display Increases frequency Preset button--------, Displays the preset stations with a short touch. Touch for at least 2 seconds to memorise the current station as a preset station. Changes tuning mode Seek mode indicator Switches band I -----I ------.....1 Memorises stations automatically _ _ _ _ ____.
DVD Owner's manual DVD Operation When you touch the DVD playback screen, the DVD operation screen is displayed. The following is an example of the DVD-VIDEO operation screen. Finds the beginning of the current chapter/Finds a previous chapter within one second after playback starts/Fast-reverses when touched for at least 2 seconds Finds the beginning of next chapter/Fast-forwards when touched for at least 2 seconds DVD information display-1 DVD information display-2 _ _......
Owner's manual iPod/iPhone (Optional) iPod/iPhone Operation (Optional) A separately sold USB iPod/iPhone AV cable (KCU-461 iV) or a separately sold Lightning to USB cable (KCU-471 i) is requ ired depending on the type of iPod/iPhone. Audio mode . . . . - - - - - - - - iPod/iPhone information display Artwork display - - - - - - - - - - - - - - .
USB Memory (Optional) Owner's manual USB Memory Operation (Optional) You can play back music files (MP3/WMA/AAC) and video files (DivX®) stored in a USB memory device on the internal player of this system. Refer to the "MP3/WMA/AAC Operation" (page 5) for information on music.
Owner's manual I BLUETOOTH Setting, BLUETOOTH Operation Hands-Free Phone Control Hands-free calls are possible when using an HFP (Hands-Free Profile) compatible mobi le phone w ith t he INEW960/INE-NAV-60/INE-W960S. How to connect to a BLUETOOTH compatible device (Pairing) The BLUETOOTH function is always available on this unit. You can, therefore, search for a BLUETOOTH device for pairing at any time. 1 Touch [Setup] icon of Top banner. [SETUP] icon • 2 Touch 3 Touch [Set BLUETOOTH Device].
Map Functions Below is an overview of different buttons and icons on the map display. For more detailed information about th is screen, please see the Owner's Manual. _r----Next Street Name Next Manoeuvre Arrow------.. Distance to next Manoeuvre Trip Information - - - - - --.. Displaying Audio/Visual Information Map Orientation------~ You can display the currently p laying information (Frequency, Track No., etc.) in the Indicator Bar of the Navigation screen.
Go to a Destination The following example briefly describes how to input a destination. 1 Touch [Go to] from Navigation Menu. I 2 Select a destination input method. ([Find Address] is selected.) • You can touch [Results] to display the cand idate list. 3 To change the State/Province, touch the button with the country name. Enter a State/Province name and select the State/ Province from the list. 4 Type in the city name or postcode until displayed in the selection list. Select the matching entry.
5 Type in the street name until displayed in the selection list. Select the matching entry. • You can touch [Results] to display the candidate list 6 7 Enter a house number. Touch [Done] to access the confirmation screen. Touch [Select] to initialize route calculation and start navigation.
Installation Installation • When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the INEW960/INE-NAV-60/INE- W960S to the fuse box, make sure the fuse for the intended circuit of the INE- W960/ INE-NAV-60/INE- W960S has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle.
Slide the unit into the mounting sleeve and secure it. Installation example using the Original Mounting Bracket • 1 Mounting Sleeve (Included) Dashboard Mount the original mounting bracket to the unit using the supplied screws. Ground Lead* Pressure Plates*' Face Plate* 2 (Included) *1 If the installed mounting sleeve is loose in the dashboard, the pressure plates may be bent slightly to remedy the problem . *2 The supplied face plate may be mounted.
Connection Diagram of SPST Switch (sold separately) (If the ACC power supply is not available) ACC INE-W960 INE-NAV-60 INE-W960S (Red) BATTERY (Yellow) .------------, I .. ___________ _ -F-IUI: :S: :JoE-. . (SA) - - ~---·---.....a·""'-----. 1 1 SPST SW (Optional) : (Optional) c FUSE(20A) (Optional) I • Ifyour vehicle has no ACC power supply, add an SPST (Single-Pole, Single- Throw) switch (sold separately) and fuse (sold separately).
Connections Connections Connections 1/2 Antenna c5-----------~;.....;.-~0 GPS (Included) ~ iPod/iPhone with a 30-pin connector (Sold separately) iPod/iPhone with a Lightning connector (Sold separately) DO t t ~~--J-.:: cc [f] g iPod VIDEO AV extension cable KCU-461 iV (Sold separately) •I (Sold separately) ~==:~--~}:=::==:====~ ~~ USB extension cable (Included) ~ Lightning to USB Cable KCU-471 i (Sold separately) I ~ --G(]t;;;;t====~J USB Memory (Sold separately) REMO .....,_ ..._.
Connections 2/2 I To SiriusXM Tuner (INE-W960/INE-NAV-60 only) v-----.;....+--~ ~ Microphone (Included) ?0.
Specifications Specifications MONITOR SECTION Screen Size LCD Type Operation System Number of Picture Elements PICKUP 6.1" Transparenttype TN LCD TFT active matrix Wave length Laser power 1,152,000 pes.
• This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation . Reverse engineering and disassembly are prohibited. • Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. • Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.
About the Rules of Bluetooth Electromagnetic Radiation Regulation USA/Canada FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-1 02 of the IC radio frequency (RF) Exposure rules.
$H/ILPINE® LIMITED WARRANTY ALPINE ELECTRONICS OF AMERICA, INC. ("Alpine"), is dedicated to quality craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below. e PRODUCTS COVERED: e HOW WE LIMIT IMPLIED WARRANTIES: This Warranty covers Car Audio Products and Related Accessories ("the product").
##DILP INE® GARANTIE LIMITEE Fidele a son engagement de ne fournir que des produits de qualite, ALPINE ELECTRONIQUE DE L'AMERIQUE, INC.(« Alpine») est heureuse de vous offrir cette garantie. Nous vous suggerons dele lire attentivement et en entier. Si vous avez Ia moindre question, veuillez contacter l'un de nos concessionnaires ou appeler directement Alpine aux numeros listes ci-dessous.
ALPINE ELECTRONICS MARKETING, INC. ALPINE ELECTRONICS OF U.K. LTD. 1-7, Yukigaya-Otsukamachi, Ota-ku, Tokyo 145-0067, JAPAN Alpine House Fletchamstead Highway, Coventry CV4 9TW, U.K. Phone: 03-5499-4531 www.alpine.co.uk ALPINE ELECTRONICS OF AMERICA, INC. ALPINE ELECTRONICS FRANCE S.A.R.L. 19145 Gramercy Place, Torrance, (RCS PONTOJSE B 338 101 280) 98, Rue de Ia Belle Etoile, Z.l. Paris Nord II, B.P. 50016, 95945 Roissy Charles de Gaulle Cedex, California 905'01, U.S.A.
R EN IN-DASH GPS NAVIGATION RECEIVER INE-W960 INE-NAV-60 INE-W960S FR ES PT • OWNER’S MANUAL Please read before using this equipment. • MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. • MODE D’EMPLOI Veuillez lire avant d’utiliser cet appareil. • MANUAL DO PROPRIETÁRIO Leia antes de usar este equipamento. Open only to legal US. residents./ Uniquement accessible aux personnes résidant légalement aux États-Unis./ Solo para ciudadanos residentes legalmente en EE.UU.
ALPINE ELECTRONICS MARKETING, INC. 1-7, Yukigaya-Otsukamachi, Ota-ku, Tokyo 145-0067, JAPAN Phone: 03-5499-4531 ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 161-165 Princes Highway, Hallam Victoria 3803, Australia Phone 03-8787-1200 ALPINE ITALIA S.p.A. Viale Cristoforo Colombo, 8 20090 Trezzano sul Naviglio MI, Italy Phone +39 02 484781 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A.
ENGLISH Contents Operating Instructions PTY (Program Type) Tuning ..........................20 Displaying Radio Text ....................................20 CD/MP3/WMA/AAC Playback ..........................................................21 PRECAUTIONS IMPORTANT INFORMATION ....................... 7 WARNING Points to Observe for Safe Usage ..................... 7 WARNING ................................................. 8 Repeat Play .....................................................21 M.I.X.
Setup Adjusting the Crossover Settings (X-Over) ...................................................... 38 Setup Operation Adjusting the Parametric Equalizer Curve (Parametric EQ) ........................................... 38 General Setup General Setup Operation ................................ 30 Text Display Setting ....................................... 30 Setting the Scroll ......................................... 30 Format Settings ...........................................
Adjusting the Caller Volume .......................... 48 Adjusting the Microphone Level .................... 48 Adjusting the Ring Tone Volume ................... 48 Deleting All the Histories ............................... 48 Changing the Phone book List Order ............. 48 Camera Setup Camera Setup Operation ................................. 49 AUX Camera Setting ...................................... 49 Setting the Camera Input .............................
Repeat Play ..................................................... 70 Random Play (Shuffle) ................................... 70 Random Play (Shuffle Songs) ........................ 70 Pandora® internet radio (optional) (INE-W960/INE-NAV-60 only) ® Installation and Connections Warning .................................................. 88 Caution ................................................... 88 Listening to Pandora ..................................... 71 Precautions ..............................
Operating Instructions PRECAUTIONS IMPORTANT INFORMATION PLEASE READ CAREFULLY BEFORE USING THIS PRODUCT This product is intended to provide turn by turn instructions to get you to a desired destination. Please make certain that all persons using this navigation system carefully read these precautions and the following instructions fully. • This product is not a substitute for your personal judgment.
DO NOT DISASSEMBLE OR ALTER. WARNING • Operation of the system while driving is dangerous. Users should stop vehicle before operating the software. • Road conditions and regulations take precedence over information contained on the map display: observe actual traffic restrictions and circumstances while driving. • This software is designed for use exclusively in the INE-W960/INE-NAV-60/INE-W960S. It cannot and may not be used in conjunction with other hardware.
NOTICE Product Cleaning Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic. Temperature Be sure the temperature inside the vehicle is between +45°C (+113°F) and 0°C (+32°F) before turning your unit on. New Discs To prevent the disc from jamming, “Disc error” is displayed if discs with irregular surfaces are inserted or if discs are inserted incorrectly.
Discs Playable on This Unit Disc Accessories There are various accessories available on the market for protecting the disc surface and improving sound quality. However, most of them will influence the thickness and/or diameter of the disc. Using such accessories can cause operational problems. We recommend not using these accessories on discs played in Alpine DVD players. Playable Discs The discs listed below can be played on this unit.
Discs that cannot be played Tips for making your own discs DVD-ROMs, DVD-RAMs, CD-ROMs (excluding MP3/WMA/ AAC files), photo CDs, etc. The INE-W960/INE-NAV-60/INE-W960S plays DVD Video, DivX®, Audio CD and has a built in MP3/WMA/AAC decoder. DualDisc This unit is not compatible with DualDisc. Using a DualDisc may cause unit malfunction, and may cause disc damage when the disc is inserted/ejected. DVD region number (playable region number) Region numbers supported by this unit are as follows.
Using DVD-Rs/DVD-RWs/DVD+Rs/DVD+RWs • This unit is compatible with discs recorded in the standard DVD-Video format. • Note that discs not finalized (processed to enable to play on playback-only DVD players) cannot be played on this DVD player. • Some discs may not play back, depending on the recording device and disc format. • Discs or files utilizing copy protection, may not be playable. Some recording systems may not properly format copied files to enable proper playback.
• This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited. • Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. • Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.
Remote Sensor Getting Started Accessory List • • • • • • • • • • • • • INE-W960/INE-NAV-60/INE-W960S .....................................1 Power cable.........................................................................1 Flush head screw (M5×8)....................................................6 Screw (M5×8) ......................................................................8 GPS Antenna ......................................................................1 Antenna mounting plate ...............
Turning the System On With the Alpine system, when the ignition key is turned to ACC or ON, the opening screen will be automatically displayed. 1 When the system is used for the first time, the language selection menu is displayed. There are 24 languages to choose from. Touch [ ] or [ ] to scroll the list, and then touch the desired language. Inserting/Ejecting a Disc Inserting the Disc Insert the disc with the label side facing up.
Top banner and Bottom banner Fade Out Setting When “Top/Bottom Banner Fade Out” is set to “ON,” the Top banner and Bottom banner on the Audio/Visual Playback screen fade out after 5 seconds if no operation is performed. To display the keys again, touch the middle of the screen. Top banner *5 If the TuneIt App is not launched, this option is not available. *6 When Camera Select is set to “Off,” this option is not available.
Touch Operation About the Indicator Display You can operate the system by using the touch panel on the screen. The Indicator Bar at the bottom of the screen displays various types of information, like the current time. • Be sure to touch the onscreen button lightly with the pad of your finger to protect the display. • If you touch a button and there is no reaction, remove your finger from the display once, and try again. • Onscreen buttons that cannot be operated appear dull in color.
Displaying Audio/Visual Information on the Navigation screen You can display the currently playing information (Frequency, Track No., etc.) in the Indicator Bar of the Navigation screen. Touch [ 18-EN ].
Radio/RBDS The RBDS (Radio Broadcast Data System) is a radio information system. The RBDS allows you to receive a variety of information such as traffic information, station names. Display example for Radio main screen Presetting Stations Manually 1 2 Tune in a desired radio station you wish to store in the preset memory by manual or automatic seek tuning. Touch and hold any one of the preset buttons for at least 2 seconds. The selected station is stored.
PTY (Program Type) Tuning FM Radio mode 1 Touch [PTY] of Bottom banner. The Select PTY list screen is displayed. 2 Touch the selected program type to start searching for a station in the type. If no PTY station is found, “No PTY.” will be displayed. Displaying Radio Text Text messages from a radio station can be displayed. 1 2 Tune in a radio station that transmits text messages. Touch [Info] in the bottom banner in FM radio mode repeatedly to switch to the desired display.
CD/MP3/WMA/AAC Repeat Play Touch [ Display example for MP3/WMA/AAC main screen ] to repeatedly play back. The tracks (files) will be played repeatedly. The repeat mode switches every time the button is touched. CD: Repeat (OFF) Repeat MP3/WMA/AAC: Repeat Repeat Folder* (OFF) * Only files in a folder are repeatedly played back. • If the Repeat Play mode is activated during M.I.X. playback, the M.I.X. mode will be canceled. Song title Artist title Album title Current song no./Total song no.
Selecting Folders (Concerning MP3/ WMA/AAC) Touch [ folder. ] or [ ] of Bottom banner to select the Searching from CD Text 1 Touch [ (Search)] of Bottom banner during playback. The CD text search screen is displayed. 2 Touch the selected track name. The selected track will be played back. • For details on how to scroll through the list, refer to “Selecting an Item in a List” (page 17). File/Folder Name Search (Concerning MP3/WMA/AAC) 1 Touch [ (Search)] of Bottom banner during playback.
Supported playback sampling rates and bit rates Order of files Files are played back in the order that the writing software writes them to the disc. Therefore, the playback order may not be what’s expected. Verity the writing order in the software’s documentation. The playback order of the folders and files is as follows. (The following numbers may differ from actually displayed numbers.
The DVD operation screen display DVD Touch the screen while the DVD playback screen is displayed. The DVD operation screen is displayed. Display example for DVD Video main screen Touch [<<], [>>] Display example for DivX® main screen Touch [<<], [>>] Information display-1 DVD-Video: Title name/Chapter No. DivX®: Title name/Current File No./Total File No.
Playing a Disc If a Menu Screen Appears On DVD mode, menu screens may appear automatically. If this happens, perform the operation described below to start playback. WARNING It is dangerous for the driver to watch the DVD/TV/ Video while driving the vehicle. The driver may be distracted from looking ahead and an accident could occur. Direct Menu Operations Touch the DVD menu directly. • Some operations cannot be performed depending on the disc.
Numeric Keypad Input Operations 1 Stopping Playback Touch [10Key] of Bottom banner. The numeric keypad input mode screen appears If [10Key] is not displayed, touch [<<] in the bottom banner to display [10Key]. 2 Touch and hold [ ] for at least 2 seconds during playback. “ ” indicator and [ ] in the middle of the screen are displayed. • Playback starts from the beginning when [ /ll] or [ ] in the middle of the screen is touched while playback is stopped. Touch a desired number.
Playing Still Frames (Pausing) 1 2 Repeat Playback Use this function to play the disc’s titles, chapters or tracks, etc., repeatedly. During playback, Touch [ Touch [ / ] or [ resume playback. / ] of Bottom banner. ] in the middle of the screen to Touch [ DVD Video • No sound is played during the still frame mode. • The image or sound may stop temporarily when playback starts from the pause mode. This is not a malfunction.
Searching Directly by Chapter Number Use this function to easily move to the beginnings of the chapters on the disc. Perform operations during playback, during PRE-STOP or while playback is paused. 1 Touch [10Key] of Bottom banner. The numeric keypad input mode screen will appear. If [10Key] is not displayed, touch [<<] in the bottom banner to display [10Key]. 2 Touch and enter the chapter number you want to play.
About DivX® DivX® is a codec (software) to compress moving images while maintaining image quality using a highly advanced compression ratio and operating speed. • Official DivX® Certified product ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos.
2 Setup Touch [General]. Setup Operation Touch the [SETUP] icon on the Audio/Visual Playback screen to display the Setup main screen. [Setup] icon The General Setup screen appears. 3 Select the desired item. General Setup General Setup Operation Setting items: Text Display / Clock Display / Top/Bottom Banner Fade Out / Screen/LED Customize / Visual / About / Installation / Demo mode • Depending on the item, repeat step 3.
Format Settings The character code to be used for tag text information displayed on the screen can be selected from 7 character codes. Setting item: Format Setting contents: Latin-1 / Latin-9 (Initial setting) / Russian / Chinese / Thai / Arabic / Hebrew Latin-1: Latin-9: Russian: Chinese: Thai: Arabic: Hebrew: ISO 8859-1 ISO 8859-15 ISO 8859-5 GB18030 CP874 CP1256 CP1255 Setting Top banner and Bottom banner Display [Top/Bottom Banner Fade Out] is selected on the General setup menu in step 3.
Adjusting the Dimmer of Button Lighting at Night You can adjust the brightness of the button lighting at night with the dimmer. Setting item: Key Illumination Level Setting level: -2 to +2 (Initial setting: 0) Visual Setting [Visual] is selected on the General setup menu in step 3. Refer to “General Setup Operation” (page 30). 1 Touch the desired item. Switching the Display Color and Wallpaper Image (Background) You can change the Display Color or Wallpaper Image.
Adjusting Brightness Setting item: Brightness Setting content: -15 to +15 (Initial setting: 0) You can adjust the brightness between MIN (-15) and MAX (+15). When it reaches the minimum or maximum point, the display shows “MIN” or “MAX” respectively. Checking the DivX® Registration This unit will display the registration code required to play a DivX® VOD (Video On Demand), or you can also display the deregistration code. Setting item: Warranty/Copyright Info.
Installation Setup [Installation] is selected on the General setup menu in step 3. See “General Setup Operation” (page 30). Setting item: Installation Sound Setup Sound Setup Operation The Installation check screen is displayed. To display the Sound Setup Menu screen: Your vehicle must be parked with the ignition key in the ACC or ON position. To do this, follow the procedures below. 1 Bring your vehicle to a complete stop at a safe location. Engage the parking brake.
4 Touch [ ] or [ ] etc., to change its setting. • When the pop-up window for setup is displayed, touch [ close the window after setting. 5 Touch [ ] to ] to return to the previous screen. • Immediately after changing the Sound Setup (while the system is writing data automatically) do not turn the ignition key to OFF. Otherwise, the settings may not be changed. Car Specific Sound Setup [Car Specific Sound Setup] is selected on the Sound setup menu in step 3.
MX CD CD mode processes a large quantity of data. This data is used to reproduce the sound cleanly by making use of the data quantity. MX SiriusXM The medium to high frequencies become more clear, and produces well balanced sound in all the bands. MX Compressed Media This corrects information that was omitted at the time of compression. This reproduces a well-balanced sound close to the original. MX Pandora This corrects information that was omitted at the time of compression.
Setting the BASS ENGINE Type Adjusting the Time Correction (TCR) You can set your favorite BASS ENGINE type. Setting contents: Standard (Initial setting) / Punch / Rich / Mid Bass / Low Bass Standard: Natural low-pitched sound located in front of front seats. Punch: Punched bass sound, massive, with a feeling of speed. Rich: You can feel wrapped with rich Low-pitched sound by arranging super-low-pass, low-pass, and mid lowpass, with sufficient balance. Mid Bass: Emphasizes the presence of an upper bass.
Adjusting the Crossover Settings (XOver) Adjusting the Parametric Equalizer Curve (Parametric EQ) [X-Over] is selected on the Sound setup menu in step 3. Refer to “Sound Setup Operation” (page 34). Before performing the following procedures, refer to “About the Crossover” (page 41). [Parametric EQ] is selected on the Sound setup menu in step 3. Refer to “Sound Setup Operation” (page 34). You can modify the Equalizer settings to create a response curve more appealing to your personal taste.
• Settings exceeding the frequency of adjacent bands are not available. • While adjusting the Parametric EQ, you should consider the frequency response of the connected speakers. • When the parametric EQ is adjusted, the adjustment for EQ Presets becomes ineffective. • When EQ Presets is set, the interlinked Parametric EQ settings are also changed. Band2 of Parametric EQ is also interlinked with the Bass adjusted setting value, and Band8 is interlinked with the Treble adjusted setting value.
These values are the time correction values for the different speakers. Setting these values to make each sound reach the listening position at the same time as the sound of other speakers. About Time Correction The distance between the listener and the speakers in a car vary widely due to the complex speaker placement. This difference in the distances from the speakers to the listener creates a shift in the sounds image and frequency characteristics.
About the Crossover Source Setup Crossover (X-Over): This unit is equipped with an active crossover. The crossover limits the frequencies delivered to the outputs. Each channel is controlled independently. Thus, each speaker pair can be driven by the frequencies for which they have been optimally designed. The crossover adjusts the HPF (high pass filter) or LPF (low pass filter) of each band, and also the slope (how fast the filter rolls off the highs or lows).
Disc Setting [Disc] is selected on the Source setup menu in step 3. Refer to “Source Setup Operation” (page 41). • You can perform DVD setup in DVD video mode. • Touch [Stop] before performing Disc setup. Setting of the DVD Menu Language To play in a language other than those displayed 1 Touch [DVD Menu Language Code], [Audio Language Code] or [Subtitle Language Code]. The numeric keypad screen is displayed. 2 Touch the 4-digit numeral of the language number.
Set the rating level of PARENTAL 4 Touch [Parental Control]. 5 Touch [ ] on [ ] to turn “On". Select “Off” to cancel parental lock or if you do not want to set a rating level. 6 Touch [ ] to return to the previous screen. 7 Touch [Parental Level] 8 Touch [ ] or [ ] to select the rating level (1 to 8). The smaller the number, the higher the restriction. 9 Touch [ ] to return to the previous screen. 4:3 PAN-SCAN: Select this when connected to a conventional 4:3 size monitor.
AUX Setting [Auxiliary (AUX)] is selected on the Source setup menu in step 3. Refer to “Source Setup Operation” (page 41). SiriusXM Setting (INE-W960/INE-NAV-60 only) [SiriusXM] is selected on the Source setup menu in step 3. Refer to “Source Setup Operation” (page 41). Setting the AUX Mode Connection with external input devices is available through the iPod VIDEO connector. An optional adapter cable is required (standard RCA to 3.5ø mini-phono plug or 3.5ø to 3.5ø mini phono plug).
Setting all Source Alert You can enable Alert even on sources other than SiriusXM. 1 2 Touch [Alert]. Touch [All Source]. Off: On: Alert is enabled only on SiriusXM. Alert is enabled even on sources other than SiriusXM. Deleting all stored Alert The operation will delete all stored songs, artists and teams alert information. 1 You can lock out channels with passcode protection. Channels that are locked cannot be accessed without entering the passcode.
Changing the Lock Passcode 4 Touch [Edit Code]. The numeric keypad screen is displayed. 5 Use the keypad to enter the current (old) 4-digit passcode. (The initial passcode is set to 0000). Touch [Enter] to confirm the entry. Touch [Delete All] to erase all of the digits that you entered. Touch [ ] to erase the last digit you entered. Touch [ ] to abort changing the passcode. 6 7 8 Now use the keypad to enter the new 4-digit passcode.
Displaying BLUETOOTH Information BLUETOOTH Setup The BLUETOOTH function is always available on this unit. You can, therefore, search for a BLUETOOTH device for pairing at any time. [Bluetooth Information] is selected on the BLUETOOTH setup menu in step 3. Refer to “BLUETOOTH Setup Operation” (page 47). You can display the BLUETOOTH device name and device address of this unit.
Deleting a BLUETOOTH Device from the list You can delete the information of a previously connected BLUETOOTH compatible device. 1 2 3 Touch [Set Bluetooth Device]. Touch [Delete] of the BLUETOOTH compatible device to delete from the Paired Device list. Adjusting the Microphone Level [Microphone Level] is selected on the BLUETOOTH setup menu in step 3. Refer to “BLUETOOTH Setup Operation” (page 47). You can adjust the microphone level, during the call.
AUX Camera Setting Camera Setup [Camera] is selected on the Camera setup menu in step 3. Refer to “Camera Setup Operation” (page 49). Camera Setup Operation With an optional camera connected, its video is output to the monitor. When the camera is connected, set this item. To display the Camera Setup Menu screen: Your vehicle must be parked with the ignition key in the ACC or ON position. To do this, follow the procedures below. 1 Bring your vehicle to a complete stop at a safe location.
Adjusting guides simultaneously (for Rear camera only) Touch [Link]. The 3 vertical guides of the currently-selected guide link together, allowing them to be adjusted simultaneously. About the Rear Camera Guide To display the guide, set “Guide Display On/Off Setting” (page 50) to On. Also, to adjust the guide, refer to “Adjusting the Rear Camera Guide” (page 49). You can also turn off the guide in the Rear camera display screen.
C B A (about 0.5 m) The distance guidance mark represents the distance to a flat road surface. Therefore in the case of an upward slope behind the car, the distance guides are displayed closer to the rear bumper than the actual distance. For example, if there is an obstacle on the upward slope, it may appear farther away than its actual position. Also, an error may occur between the guidance and the actual path of the car on the road surface.
BLUETOOTH Operation Setup Before Using Before Using BLUETOOTH Before using the hands-free phone/audio function, the following settings need to be made. Register a BLUETOOTH device in this unit (see page 47). • You can search for this unit using a BLUETOOTH compatible device, and then connect that BLUETOOTH compatible device to this unit. The device name of this unit is “INE-W960/INE-NAV-60/INEW960S” and the initial number of the passcode is “0000.
Changing the connecting BLUETOOTH Device If multiple BLUETOOTH devices are registered in this device, you can change the connection among the registered devices. 1 (Phone) button. Press the The Phone menu screen is displayed. 2 Touch [Change Device]. The Set Bluetooth Device screen is displayed. 3 Calling Use the Phone menu screen to make a phone call. Using Short Cut Dialing to Make a Call You can assign up to 4 phone numbers for one-touch dialing to make a call easily.
Dialing a Number in the Phone Book You can use the phone book of the mobile phone to make a phone call. Before using, you need to transfer the phone book from the mobile phone to the system. For details on how to transfer the phone book, refer to “Synchronizing the Phone Book” (page 55). 1 Voice Dial Function While connecting to a voice dial compatible hands-free phone, you can make a telephone call by voice dial operation. 1 Press and hold the seconds. (Phone) button for at least 3 (Phone) button.
Operations During a Conversation Phone Book Function Display example Display example for Phone Book screen An icon is displayed to indicate that multiple phone numbers are registered under an entry. Name, Phone number, Type* * Depending on the model, Type may not be displayed. Conversation time Synchronizing the Phone Book Adjusting the Speech Volume You can adjust the transmit volume and receive volume respectively. Touch [ ] or [ ] for “Vol.
Searching in the Phone Book Assigning as a Short Cut Dialing Number If there are 6 or more entries in the phone book you transferred, you can make a call using the phone book search function. Assigning from Call History 1 1 Press the (Phone) button. The Phone menu screen is displayed. 2 Touch [ ]. The Contact list screen is displayed. 3 Touch [Search]. The Keypad input screen is displayed. 4 Input the first letter of an entry you want to search for.
Call Waiting Function If a call comes in from another phone during a call, a notice is displayed on the screen. This function can only be used if the connected mobile phone has a call waiting function service included. BLUETOOTH Audio If a BLUETOOTH compatible mobile phone, portable player, etc. is connected by wireless, you can play back a song (operation is controllable from the unit).
Repeat Play Available for AVRCP Ver. 1.3 and 1.4 only. Touch [ ] during playback. The repeat mode switches every time the button is touched. (FILE) (ALL) (OFF) • Operations may differ depending on the connected BLUETOOTH compatible device. M.I.X. (Random Play) Available for AVRCP Ver. 1.3 and 1.4 only. Touch [ ] during playback. The M.I.X. mode switches every time [ ] is touched. (ALL) (OFF) • Operations may differ depending on the connected BLUETOOTH compatible device.
Auxiliary Device (Optional) AUX Operation Screen Display During Video File Playback Touch the screen. The AUX operation screen is displayed. Example for AUX, DVD, Game mode display Operating Auxiliary Devices (Optional) To operate devices connected to the AUX terminals of INE-W960/INENAV-60/INE-W960S, follow the procedure described below. • Set AUX In to “AUX.” Refer to “Setting the AUX Mode” (page 44). • Depending on the connected unit, the onscreen buttons may not work, or their operation may differ.
About the DVD Operation Screen Menu operation mode screen display example When the external DVD player playback screen is displayed, you can touch the screen to display the operation screen. For details on how to operate, refer to the Owner’s Manual of the connected DVD player. External DVD player display example [Key] The menu operation mode will be displayed. [ Touch [<<], [>>] ], [ ] Moves key panel location. [ ] Closes menu operation mode. [ ] Closes key panel.
About the DVD Changer Operation Screen When the External DVD changer playback screen is displayed, you can touch the screen to display the operation screen. For details on how to operate, refer to the Owner’s Manual of the connected DVD changer. • The DVD-CHG. operation mode screen and the Menu operation mode screen are the same as the external DVD player operation screen. Refer to “Operating an External DVD Player.
Applying TuneIt This unit’s sound tuning is programmable from a connected Smartphone. It is also possible to download specific parameters for certain vehicles from Alpine’s TuneIt database stored in the Cloud. Using the TuneIt App, customized parameters can also be uploaded for others to share and rate. Through this unit, it is also possible to receive and respond to information from Alpine’s Social Network Service (SNS) available through the connected Smartphone.
Displaying the Notification List Touch the Notification List icon on the Top banner, or the notification display. (List) of Example of the Notification List display Camera Operation (Optional) When an optional camera is connected, the view video of camera can be output to the monitor. Depending on your camera, please choose the camera type first. For details, refer to “Camera Setup” (page 49). Rear camera: • If there are no notifications in the Notification List, “No Notifications.” is displayed.
About creating a tag information library USB Memory (Optional) You can scan music files in a USB memory device and create a library of tag information in this unit. Library creation starts when the USB memory device is connected. The time it takes to create the library depends on the number of files in the USB memory device, but it may take several minutes. You can play back music files (MP3/WMA/AAC) and video files (DivX® ) stored in a USB memory device on the internal player of this system.
Repeat Play Random Play (Shuffle Songs) Operation differs depending on whether the most recent song search was a Tag Search or a Folder/File Search. This operation is available only if the most recent song search was a Tag Search. Touch [ 1 ] during playback. The repeat mode switches every time the button is touched. Folder/File Search mode: Repeat The Category List screen is displayed. Repeat Folder* (OFF) Repeat (OFF) 2 Touch [Shuffle Songs].
For example: Searching by Artist name The following example explains how an ARTISTS search is performed. Another search mode can be used for the same operation, although the hierarchy differs. Searching by artist name 1 Touch [Artists]. Direct Up/Down Function This operation is available only if the most recent song search was a Tag Search. Playlist/Artist/Album/Genre/Composer can be easily changed. For example, if you listen to a song from a selected album, the album can be changed.
iPod/iPhone (Optional) Display example for iPod/iPhone main screen (Info mode) Audio mode A separately sold USB iPod/iPhone AV cable (KCU-461iV) or a separately sold Lightning to USB cable (KCU-471i) is required depending on the type of iPod/iPhone. When the INE-W960/INE-NAV-60/INE-W960S is connected by the above cable, the controls on the iPod are disabled. • An iPod/iPhone with the Lightning connector does not support iPod video playback on the unit. • Internet or telephone functions, etc.
Searching by artist name Playback 1 1 Touch [iPod (Audio or Video)] of Top banner. Touch [ (Search)] of Bottom banner during playback. The Search screen is displayed. The display shows the iPod mode screen. 2 Touch [ ] or [ ] or to select the desired track (file). Returning to the beginning of the current track (file): Touch [ ]. Fast reverse : Touch and hold [ ]. Advancing to the beginning of the next track (file) : Touch [ ]. Fast forward : Touch and hold [ ]. 3 2 Touch [Artists].
Searching for a Desired Video File Direct Up/Down Function You can select a movie, music video, etc., from the list screen. If you touch [ ] of the album name in the search mode, this album will be played back repeatedly. To go to the previous or next Album, use the Direct Up/Down Function. • Video search mode depends on the iPod/iPhone. If the specification of the iPod/iPhone is changed, the search mode on this unit will also be changed.
Repeat Play Touch [ ] to repeatedly play back the currently track. The tracks (files) will be played repeatedly. Touch [ ] again to deactivate Repeat play. Repeat (OFF) Repeat Random Play (Shuffle) Touch [ ] during playback. The files will be played back in a random sequence. The Shuffle mode switches every time [ ] is touched. Shuffle Songs Shuffle Albums (OFF) Shuffle Songs Shuffle Albums: The songs on each album are played back in proper order.
Pandora® internet radio (optional) (INE-W960/INENAV-60 only) Pandora® internet radio is your own FREE personalized radio now available to stream music on your Smartphone (which runs Android OS, iOS or BlackBerry OS). Just start with the name of one of your favorite artists, songs or classical composers and Pandora® will create a “station” that plays their music and more music like it.
Searching for a Desired Station QuickMix You can display your station list and select stations directly from the INE-W960/INE-NAV-60. Alphabet Search Use QuickMix to create a playlist based on two or more of your Pandora stations. Edit your QuickMix station selections on the Pandora Compatible Application for iPhone when it is not connected to the INEW960/INE-NAV-60. 1 1 2 3 Touch [ (Search)] of Bottom banner to activate the Search mode.
How to Input Characters and Numbers (Keypad) The displayed screens and procedures may vary slightly depending on the function used, but the basic input method is the same. Input screen area. (Delete) Returns to the previous character and erases it. Touching here for more than 2 seconds will erase all input characters. Character keypad (Space) Confirms input characters.
SiriusXM Satellite Radio (Optional) (INE-W960/INENAV-60 only) SiriusXM Tuner operation: When an optional SiriusXM Tuner is connected to this unit, the following operations may be performed. Display example for SiriusXM main screen 1 Touch the [SiriusXM] on the Top banner. The SiriusXM main screen display appears. • The SiriusXM source selection icon will not be listed if the SiriusXM Tuner is not connected properly. Check the tuner connections if the icon is not shown.
Changing the Display Tuning Channels Using Presets Text information, such as the channel name, artist name/feature, and song/program title, is available with SiriusXM. The unit can display this text information as explained below. 1 Touch [Info] in SiriusXM mode. 2 Each time you touch this button, the display changes as shown below. Touch [Band] on the Bottom banner repeatedly until the desired band is displayed. Touch any one of the preset buttons that has a channel stored to it.
Searching by My Games 1 Touch [My Games]. This is displayed only when games for stored teams are broadcasting. 2 Touch the desired team. The channel of the selected game being broadcast is received. • Touch [Info] on the channel name search screen, the information of the broadcasting channels will be displayed. You can choose the desired channel from the league name list or team name list. Each time you touch the [Info] button, the display changes as below.
Replay Function Parental Control Function In SiriusXM mode, you can pause, rewind and replay live Satellite Radio. The Parental Control feature allows you to limit access to any SiriusXM channels, including those with mature content. For information on setting the Parental Control passcode, refer to “Setting the Parental Lock” (page 45). When a locked channel is selected, “Channel Locked” is displayed and then the numeric keypad appears for you to enter the passcode.
Multi story function* Information With this function, a single movie includes various story lines. You can select different story lines to view various versions of the same movie. Operation differs from disc to disc. Story line selection screens including instructions appear during the movie. Just follow the instructions. Product Software Update This product use software that can be updated through a USB memory device.
List of Language Codes (For details, see page 42.
List of Country Codes (For details, see page 42.
Abbreviation PE PF PG PH PK PL PM PN PR PT PW PY QA RE RO RU RW SA SB SC SD SE SG SH SI Code 8069 8070 8071 8072 8075 8076 8077 8078 8082 8084 8087 8089 8165 8269 8279 8285 8287 8365 8366 8367 8368 8369 8371 8372 8373 Country Abbreviation Peru SJ French Polynesia SK Papua New Guinea SL Philippines SM Pakistan SN Poland SO SR Saint Pierre and Miquelon ST Pitcairn SV Puerto Rico SY Portugal SZ Palau TC Paraguay TD Qatar TF Reunion TG Romania TH Russian Federation TJ Rwanda TK Saudi Arabia TM Solomon Islands
In Case of Difficulty If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected, or then consult your authorized Alpine dealer. Basic No function or display. • Vehicle’s ignition is off.
Playback does not start. • Disc is loaded upside-down. - Check the disc and load it with the labeled side facing upward. • Disc is dirty. - Clean the disc. • A disc not able to play back with this unit is loaded. - Check if the disc is able to be played back. • Parental lock is set. - Cancel the parental lock or change the rating level. Picture is unclear or noisy. • Disc is being fast-forwarded or fast-reversed. - The picture may be slightly disturbed, but this is normal. • Vehicle’s battery power is weak.
Navigation The vehicle’s position is erroneous. • The GPS reception is poor. - Drive the vehicle in an area of good GPS reception to allow the unit to recalibrate itself. Move to a location where strong GPS reception is possible. Video resolution not supported. • The file being played is a DivX® file with an unsupported resolution. - Play a DivX® file with a supported resolution. SiriusXM No operation • Moisture condensation - Allow enough time for the condensation to evaporate (about 1 hour).
PICKUP Specifications Wave length MONITOR SECTION Laser power Screen Size 6.1" LCD Type Transparent type TN LCD Operation System TFT active matrix Number of Picture Elements 1,152,000 pcs. (800 × 3 × 480) Effective Number of Picture Elements 99% or more Illumination System LED FM TUNER SECTION Tuning Range Mono Usable Sensitivity 50 dB Quieting Sensitivity Alternate Channel Selectivity Signal-to-Noise Ratio Stereo Separation Capture Ratio 87.7 – 107.9 MHz 9.3 dBf (0.8 µV/75 ohms) 13.5 dBf (1.
END USER LICENSE AGREEMENT (Microsoft) You have acquired a device (“DEVICE”) that includes software licensed by Alpine Electronics, Inc. (collectively “ALPINE”) from an affiliate of Microsoft Corporation (collectively “MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.
INTELLECTUAL PROPERTY RIGHTS. All title and intellectual property rights in and to the SOFTWARE (including but not limited to any images, photographs, animations, video, audio, music, text and “applets,” incorporated into the SOFTWARE), the accompanying printed materials, and any copies of the SOFTWARE, are owned by MS, Microsoft Corporation, their affiliates or suppliers. The SOFTWARE is licensed, not sold. You may not copy the printed materials accompanying the SOFTWARE.
Installation and Connections Before installing or connecting the unit, please read the following and pages 7 to 12 of this manual thoroughly for proper use. Caution HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. Warning MAKE THE CORRECT CONNECTIONS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
3 Installation For safe use, make sure of the following: • location is stable and firm. • driver’s view and operations are not obstructed. • microphone is located where the driver’s voice can be easily picked up (on the sun visor, etc.). Caution Do not block the unit’s fan or heat sink, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire. Mounting the Microphone.
5 Reinforce the head unit with the metal mounting strap (not supplied). Secure the ground lead of the unit to a clean metal spot using a screw (*1) already attached to the vehicle’s chassis. Connect all the leads of the INE-W960/INE-NAV-60/INE-W960S according to details described in the “Connections” (page 92). Installation example using the Original Mounting Bracket 1 Mount the original mounting bracket to the unit using the supplied screws.
Connection Diagram of SPST Switch (sold separately) (If the ACC power supply is not available) ACC INE-W960/ INE-NAV-60/ INE-W960S (Red) SPST SW (Optional) FUSE (5A) (Optional) BATTERY (Yellow) FUSE (20A) (Optional) Battery • If your vehicle has no ACC power supply, add an SPST (Single-Pole, Single-Throw) switch (sold separately) and fuse (sold separately). • The diagram and the fuse amperage shown above are in the case when INE-W960/INE-NAV-60/INE-W960S is used individually.
Connections GPS Antenna (Included) Vehicle Antenna Microphone (Included) AUX OUTPUT (Yellow) To Rear Monitor Input terminal REAR OUTPUT (Red/White) FRONT OUTPUT (Red/White) To input terminal of amplifier when adding an external amplifier SUBW (Red/White) CAMERA To Camera with RCA Output terminal (Yellow) REMOTE OUT (Brown) To remote input lead REMO To amplifier or equalizer (Blue/White) To plus side of the back lamp signal lead of the car REVERSE (Orange/White) P.
Radio Antenna Receptacle Reverse Lead (Orange/White) Video Output Connector (AUX OUTPUT) (Yellow) Connect to the plus side of the car’s reverse lamp. This lamp illuminates when the transmission is shifted into reverse (R). With this lead properly wired, the video picture automatically switches to the rear camera whenever the car is put into reverse (R). SiriusXM Tuner Input Connector (INE-W960/INE-NAV60 only) Rear Output RCA Connectors It can be used as Rear Output RCA Connectors.
System Example Connection of an iPod/iPhone with Lightning connector or USB memory USB connector iPod/iPhone with Lightning connector (Sold separately) USB extension cable (Included) or Lightning to USB Cable KCU-471i (Sold separately) USB Memory (Sold separately) • Do not leave a iPod/iPhone/USB memory in a vehicle for a long time. Heat and humidity may damage the iPod/iPhone/USB memory and you may not be able to play it again.
Connection of an External device iPod VIDEO input connector CAMERA/AUX/PRE OUT Connector To Audio Output terminal To Video Output terminal CAMERA/AUX/PRE OUT cable DVD Changer (Sold separately) REMOTE OUT REMOTE IN (Brown) (White/Brown) 1 AV/RCA interface cable (4-pole mini AV plug to 3RCA) (Sold separately) 2 Video/Audio Input Connectors YELLOW is for input video, RED is right and WHITE is left input the audio.
Connection of a DVD Player To Video Output terminal DVD Player (Sold separately) To Audio Output terminal iPod VIDEO input connector AV/RCA interface cable (4-pole mini AV plug to 3RCA) (Sold separately) RCA Extension Cable (Sold Separately) Video/Audio Input Connectors YELLOW is for input video, RED is right and WHITE is left input the audio. • You can change the name of an external device. Refer to “Setting the AUX Mode” (page 44).
Connection of an External Amplifier Power Supply Connector CAMERA/AUX/PRE OUT Connector CAMERA/AUX/PRE OUT cable Amplifier 4 ch (Sold separately) (Red) (White) Input Front speaker Input Rear speaker (Red) (White) Amplifier for subwoofer (Sold separately) (Red) Input (White) REMOTE TURN-ON REMOTE ON (Blue/White) (Blue/White) Subwoofer REMOTE ON Power Supply Connector 1 Front Output RCA Connectors RED is right and WHITE is left.
Connection of cameras CAMERA/AUX/PRE OUT Connector CAMERA/AUX/PRE OUT cable (Yellow) To Video Output terminal Camera with RCA video output (Sold separately) Power Supply Connector Reverse Lead HCE-C105, etc. Connect to the plus side of the car’s reverse lamp.
About the Rules of Bluetooth Electromagnetic Radiation Regulation USA/Canada FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
LIMITED WARRANTY ALPINE ELECTRONICS OF AMERICA, INC. (“Alpine”), is dedicated to quality craftsmanship and is pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below. PRODUCTS COVERED: This Warranty covers Car Audio Products and Related Accessories (“the product”). Products purchased in the Canada are covered only in the Canada. Products purchased in the U.S.A.
User Manual Alpine Navigation Navigation software for the Alpine INE-W960/INE-W960S/INE-NAV-60 US English January 2015, ver. 1.
Thank you for choosing the Alpine unit as your navigator. Start using your device right away. This document is the detailed description of the navigation software. You can easily discover the software while you are using it; however, we still recommend that you read this manual to fully understand the screens and features.
Table of contents 1 Warnings and Safety information ......................................................................................... 6 2 Getting started ......................................................................................................................... 7 2.1 Buttons and other controls on the screen .........................................................................................8 2.1.1 Using keyboards.....................................................................
3.1.3 Using the free form search ..................................................................................................................... 46 3.1.4 Selecting a map location as the destination ............................................................................................ 47 3.1.5 Selecting the destination from your Address Book ................................................................................ 48 3.1.6 Selecting a recent destination from the History ...................
6 Glossary .................................................................................................................................. 78 7 Copyright note .......................................................................................................................
1 Warnings and Safety information The navigation system helps you find your way to your destination with a connected GPS receiver. The software does not transmit your GPS position; others cannot track you. It is important that you look at the display only when it is safe to do so. If you are the driver of the vehicle, we recommend that you operate your software before you start your journey. Plan the route before your departure and stop if you need to change the route.
2 Getting started When using the navigation software for the first time, an initial setup process starts automatically. Do as follows: 1. Select the written language of the application interface. Later you can change it in Regional settings (page 76). 2. Read the End User License Agreement. Tap 3. The Configuration wizard starts. Tap 4. Select the language and speaker used for voice guidance messages. Later you can change it in Sound and Warnings settings (page 76). 5.
6. If needed, modify the default route planning options. Later you can change them in Route settings (page 70). 7. The initial setup is now complete. The Configuration wizard can be restarted later from the Settings menu (page 67). After the initial setup, the Map screen appears and you can start using the software. 2.1 Buttons and other controls on the screen When you are using the software, you usually tap buttons on the touch screen.
List When you need to select from Grab the list anywhere and several options, they appear in a slide your finger up or down. list. Depending on the speed of the sliding, the list will scroll fast or slow, only a bit or till the end. Alternatively, move between pages with the and buttons and tap the value that you want. Radio button When there are only a few choices, radio buttons may be used instead of lists. Only one value can be selected. Tap one of the buttons to select a new value.
Correcting your entry on the keyboard Tap to remove the unneeded character(s). Tap and hold the button to delete several characters or the entire input string. Entering a space, for example between a first name and a family name or in multi-word street names Tap the Entering upper and lower case letters When entering a text, the first character appears in upper case while button at the bottom center of the screen. the rest of the text is in lower case.
Tapping and holding the Tap and keep pressing the following buttons to reach extra functions: screen Gestures (drag&drop) Tap and hold any of the , , , , , and buttons on the Map screen: you can rotate, tilt or scale the map continuously. Tap and hold on keyboard screens: you can delete several characters quickly. Tap and hold continuously. or in long lists: you can scroll pages You need to drag and drop the screen only in cases like: Moving the handle on a slider.
There are screen buttons and data fields on the screen to help you navigate. During navigation, the screen shows route information. Two data fields are displayed on the left. The data fields are different when you are navigating an active route and when you have no specified destination (the orange line is not displayed). There are no data fields without a given destination.
2.2.2 Position markers 2.2.2.1 Vehimarker and Lock-on-Road When your GPS position is available, the software marks your current position with the Vehimarker. By default, this marker is a blue arrow, but you can change this icon in Settings. When on-road navigation is selected, the Vehimarker may not show your exact GPS position and heading. If roads are near, it is aligned to the nearest road to suppress GPS position errors, and the direction of the icon is aligned to the direction of the road.
2.2.3.2 Turn preview and Next street When navigating a route, the top section of the Map screen shows information about the next route event (maneuver) and the next street or the next city/town. There is a field in the top left corner that displays the next maneuver. Both the type of the event (turn, traffic circle, exiting freeway, etc.) and its distance from the current position are displayed. Most of these icons are very intuitive. The following table lists some of the frequently shown route events.
Approaching a waypoint. Approaching the destination. These fields also act as buttons: Tap the Turn preview field and the voice guidance will repeat the latest instruction with updated distance information. Tap the Next street field to open the Itinerary. 2.2.3.3 Lane information and Signposts When navigating on multilane roads, it is important to take the appropriate lane in order to follow the recommended route.
This feature can be turned off in Visual Guidance settings. 2.2.3.5 Freeway exit services You may need a gas station or a restaurant during your journey. This feature displays a new button on the map when you are driving on freeways. Tap this button to open a panel with the details of the next few exits or service stations. Tap any of them to display it on the map and add it as a waypoint to your route if needed.
2.2.3.7 Elements of the active route Your software shows the route in the following way: Symbol Name Current GPS position and Start point Description Your current position displayed on the map. If roads are near, it is aligned to the nearest road. Normally if GPS position is available, the route starts from the current position. If there is no valid GPS position, your software uses the last known position as the start point.
Zooming in and out Changes how much of the map is displayed on the screen. , Your software uses high-quality vector maps that let you examine the map at various zoom levels, always with optimized content. It always displays street names and other text with the same font size, never upside-down, and you only see the streets and objects that you need. Map scaling has a limit in 3D map view mode. If you zoom out further, the map switches to 2D view mode.
2.2.5 Checking the details of the current position (Where Am I?) This screen contains information about the current position (or about the last known position if GPS reception is not available) and a button to search for useful Places nearby. . You can access this screen from the map in one of the following ways: If the current street is displayed below the Vehimarker (the current position on the map), tap it to open the Where Am I? screen. In the Navigation menu, tap and then .
: Police stations : Gas stations Tap any of the buttons, select a Place from the list, and navigate to it. 2.3 Navigation menu You can reach all parts of the software from the Navigation menu. When you open the menu, the destination search buttons appear on the screen. Tap any other menu button at the top and their feature buttons appear below.
3 On-road navigation When first started, Alpine unit calculates routes using the road network of the high quality vector maps provided with the product. You can set up your route in different ways: If you need a route for immediate navigation, you can select the destination and start navigating to it right away (normal navigation).
any of the above, starting the search with the ZIP code (page 34) You can also search for an address with the free form search (page 46). 3.1.1.1 Entering an address (United States) To enter an address as the destination, do as follows: 1. In the Navigation menu, tap the following buttons: , . 2. By default, the software proposes the country and state where you are. If needed, tap , enter the first few letters of the destination country or state on the keyboard, and select one from the list.
4. Enter the street name: a. Start entering the street name on the keyboard. b. Find the street you need: The most likely street name is always shown in the input field. To accept it, tap If the desired name does not show up, the names that match the string appear in a list after entering a couple of characters (to open the list of results before it appears automatically, tap 5. 6. ). Select the street from the list. Enter the house number: a. Enter the house number on the keyboard.
If you know that you will use this destination frequently, before tapping to confirm the destination, put it in the Address Book first: tap Tip! then , give a name for the new entry, and tap to save the location. The map with the destination returns automatically. Now you can start your journey. 3.1.1.2 Entering an address (Canada) To enter an address as the destination, do as follows: 1. In the Navigation menu, tap the following buttons: , . 2.
If the desired name does not show up, the names that match the string appear in a list after entering a couple of characters (to open the list of results before it appears automatically, tap 4. ). Select the city/town from the list. Enter the street name: a. Tap (if you have selected a city/town above, this step is not needed). b. Start entering the street name on the keyboard. c. Find the street you need: The most likely street name is always shown in the input field. To accept it, tap .
6. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( ) appears at the new location. Tap to confirm the destination, or tap to select a different destination. 7. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap to modify route parameters, or tap and start your journey. 3.1.1.
The most likely city/town name is always shown in the input field. To accept it, tap . If the desired name does not show up, the names that match the string appear in a list after entering a couple of characters (to open the list of results before it appears automatically, tap 1. ). Select the city/town from the list. Enter the street name: a. Tap needed). b. Start entering the street name on the keyboard. c.
5. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( ) appears at the new location. Tap to confirm the destination, or tap to select a different destination. 6. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap to modify route parameters, or tap and start your journey. 3.1.1.
3. Enter the street name: a. Tap . b. Start entering the street name on the keyboard. c. Find the street you need: The most likely street name is always shown in the input field. To accept it, tap . If the desired name does not show up, the names that match the string appear in a list after entering a couple of characters (to open the list of results before it appears automatically, tap ). Select the street from the list. 4. 5. Enter the house number: a.
3.1.1.5 Entering the midpoint of a street as the destination You can navigate to the midpoint of a street if the house number is not available: 1. In the Navigation menu, tap the following buttons: 2. Select the country, state and city/town as described earlier (page 22). 3. Enter the street name: a. Tap b. Start entering the street name on the keyboard. c. Find the street you need: . (if you have selected a city/town above, this step is not needed).
5. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( ) appears at the new location. Tap to confirm the destination, or tap to select a different destination. 6. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap to modify route parameters, or tap and start your journey. 3.1.1.
4. Instead of entering the house number, tap selected as the destination. . The midpoint of the street is 5. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The Cursor ( to confirm the destination, or tap ) appears at the new location. Tap to select a different destination. 6. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated.
3.1.1.7 Selecting a city/town center as the destination The city/town center is not the geometric center of the city/town but an arbitrary point the map creators have chosen. In towns and villages, it is usually the most important intersection; in larger cities, it is one of the important intersections. 1. In the Navigation menu, tap the following buttons: , 2. Select the country and state as described earlier (page 22). 3. Select the destination city/town: . a. Tap b.
to confirm the destination, or tap to select a different destination. 6. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap to modify route parameters, or tap and start your journey. 3.1.1.8 Entering an address with a ZIP code All of the above address searching possibilities can be performed with entering the ZIP code instead of the city/town name. Find below an example with a full address: 1.
4. Enter the street name: a. Tap . b. Start entering the street name on the keyboard. c. Find the street you need: The most likely street name is always shown in the input field. To accept it, tap . If the desired name does not show up, the names that match the string appear in a list after entering a couple of characters (to open the list of results before it appears automatically, tap 5. 6. ). Select the street from the list. Enter the house number: a.
7. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap to modify route parameters, or tap and start your journey. 3.1.1.9 Tips on entering addresses quickly When you are entering the name of a city/town or a street: Only those letters are offered on the keyboard that appear in possible search results. All other characters are grayed out.
3.1.2 Selecting the destination from the Places of Interest You can select your destination from the Places of Interest included with your software.
4. (optional) The Places in the list are ordered by the length of the necessary detour (when navigating a route) or by their distance from the current position (when no destination is given). If you need to reorder the list, tap . 5. Browse the list if necessary and tap one of the list items. A full screen map appears with the selected point in the middle. The name and address of the Place is displayed at the top of the screen. 6. (optional) Tap to see the details of the selected Place.
2. The preset search categories appear: : If an active route exists, gas stations are searched along the route. If there is no active route (destination is not selected), they are searched around the current position. If the current position is not available either (no GPS signal), they are searched around the last known position. : If an active route exists, parking lots are searched around the destination of the route.
4. (optional) The Places in the list are ordered by their distance from the current or last known position, from the destination or by the length of the necessary detour. If you need to reorder the list, tap . 5. Browse the list if necessary and tap one of the list items. A full screen map appears with the selected point in the middle. The name and address of the Place is displayed at the top of the screen. 6. (optional) Tap to see the details of the selected Place. Tap to return to the map. 7.
Tap to search for a place within a selected city/town. (The result list will be ordered by the distance from the center of the selected city/town.) Tap to search for a place around the destination of the active route. (The result list will be ordered by the distance from the destination.) Tap to search along the active route, and not around a given point.
7. Sometimes the list of brands in the selected Place subcategory appears. Select one brand or tap to list all Places in the selected subcategory around the selected location or along the route. 8. Finally, the results appear in a list. 9. (optional) The Places in the list are ordered by their distance from the current or last known position, from the selected city/town, from the destination or by the length of the necessary detour. If you need to reorder the list, tap . 10.
13. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap to modify route parameters, or tap and start your journey. 3.1.2.4 Searching for a Place of Interest by name You can search for Places of Interest by their names. You can search around different locations or along your route in the whole Place database or in one Place category or subcategory only. 1. In the Navigation menu, tap the following buttons: , 2. Tap 3.
4. (optional) If you have selected , select the city/town to search in. 5. Select one of the main Place categories (e.g. Accommodation) to search in or tap to search among all Places. 6. Select one of the Place subcategories (e.g. Hotel or Motel) to search in or tap to search in the selected Place category. 7. Tap if you have not done it before.
8. Using the keyboard, start entering the name of the Place. 9. After entering a few letters, tap containing the entered character sequence. to open the list of Places with names 10. (optional) The Places in the list are ordered by their distance from the current or last known position, from the selected city/town, from the destination or by the length of the necessary detour. If you need to reorder the list, tap . 11. Browse the list if necessary and tap one of the list items.
3.1.3 Using the free form search A quick way to search for an address, a Place, an Address Book entry or a History item is to use the free form search. Do as follows: 1. In the Navigation menu, tap . 2. Open the 3. In the left field enter the name you are looking for. It can be a street address (just the street name or both the street and the house number), the name of a Place, a previous destination or an Address Book entry. 4.
to confirm the destination, or tap to select a different destination. 8. After a short summary of the route parameters, the map appears showing the entire route. The route is automatically calculated. Tap to modify route parameters, or tap and start your journey. 3.1.4 Selecting a map location as the destination 1. In the Navigation menu, tap the following buttons: , . 2. Locate your destination on the map: move and scale the map as needed. 3.
3.1.5 Selecting the destination from your Address Book You can select a location that you have already saved as an Address Book entry to be your destination. Adding a location to the Address Book is described on page 57. 1. Access the Address Book: in the Navigation menu, tap 2. The Address Book is displayed. 3. Tap the entry that you want to set as your destination. If necessary, browse down to see more of the list or tap 4. and then tap . and enter a few letters from the name of the entry.
3.1.6 Selecting a recent destination from the History The destinations that you have set earlier appear in the History. 1. Access the History: If you are in the Navigation menu, tap and then tap . 2. The list of recent destinations appears. Smart History promotes three destinations to the first page based on your previous routes (most likely destinations). The rest of the destinations are ordered by time they were last selected. If necessary, scroll the list to see earlier destinations. 3.
3.1.7 Entering the coordinate of the destination You can also select a destination by entering its coordinate. Do as follows: 1. In the Navigation menu, tap . 2. Open the 3. You can enter the latitude and longitude values in any of the following formats: decimal degrees; degrees and decimal minutes; or degrees, minutes and decimal seconds. 4. (optional) If necessary, tap in UTM format. 5. When finished, tap 6. A full screen map appears with the selected point in the middle.
3.1.8 Navigate to a location stored in a picture You can also set the location stored in a picture as your destination. Do as follows: 1. In the Navigation menu, tap . 2. Open the 3. The list of picutres stored on the USB memory appears. Select one picture from the list. 4. A full screen map appears with the selected point in the middle. If necessary, tap the map menu and tap . somewhere else to modify the destination.
3.1.9 Building a route from the list of destinations (Create Route) You can also build your route destination by destination from the Route menu. 1. In the Navigation menu, tap . 2. Tap 3. There is only one line in the list of route points, the start point of the route, normally the current GPS position. 4. Tap 5. The Destination menu appears and you can select the destination of the route the same way as described in the previous sections. 6.
3.2 Viewing the entire route on the map It is easy to get a map overview of the active route. Do as follows: 1. In the Navigation menu, tap . 2. Tap . The active route is displayed in its full length on the map together with additional information and controls. 3.3 Modifying the route When navigation is already started, there are several ways to modify the active route. The following sections show some of those options. 3.3.
Tap to add the newly selected location as an intermediate destination to your route. The other destinations of the route remain intact. Note: the new waypoint is placed among destinations to keep the route optimal. To decide where a waypoint to appear, use the Edit Route feature. Tap to append the newly selected destination at the end of the route. The other destinations of the route remain intact. The previous final destination is now the last waypoint. 3.3.
4. The Destination menu appears and you can select the start point of the route the same way you select a destination. 5. When the new start point is set, tap 6. The map returns with a transparent Vehimarker (showing that there is no GPS reception). If an active route already existed, it is now recalculated starting from the selected location. 7. To return to normal navigation, tap . . 3.3.3 Editing the list of destinations (Edit Route) You can edit the route by modifying the list of destinations.
Tap to delete a destination. Tap to modify the start point of the route. Tap to reorder the list. You can do it manually or you can let the application optimize the route for you. 3.3.4 Canceling the active route To cancel the navigated route, tap route is deleted with all its waypoints. in the Navigation menu, and then tap .. The active 3.3.5 Checking route alternatives To recalculate the active route with a different route planning method, you can modify the Route settings.
4. Or if you cannot find a good alternative, tap different routing methods. and scroll down for routes with 5. Select one of the route alternatives then tap to return to the Map screen. The software recalculates the route. The orange line now shows the new recommended route. 3.4 Saving a location as an Address Book entry You can add any location to the Address Book, the list of frequently used destinations. Planning a route to one of these destinations was described earlier. 1.
3.5 Saving a location as an alert point You can save any map location as an alert point (for example a speed camera or a railroad crossing). 1. Browse the map and select a location. The red Cursor appears there. 2. Tap 3. Scroll down the list and tap 4. On the newly opened screen, select the type of the alert point, the direction from which you expect the alert, and (if applicable) the speed limit for this alert point. 5. Tap . . to save the location as a new alert point. 3.
3. Scroll down the list and tap . 4. On the newly opened screen, modify the type of the alert point, the direction from which you expect the alert, or (if applicable) the speed limit for this alert point. 5. Tap to save the changes to the alert point. 3.7 Watching the simulation of the route You can run a simulated navigation that demonstrates the active route. Do as follows: 1. In the Navigation menu, tap . 2. Tap 3. Tap .
1. (optional) You have the following controls during the simulation: : Jump to the next route event (maneuver). : Pause the simulation. : Jump to the previous route event (maneuver). 2. Tap : Tap to increase the speed of the simulation to 4, 8 or 16 times faster. Now tap again to return to the normal speed. to stop the simulation.
4 Off-road navigation When first started, Alpine unit calculates routes using the road network of the high quality vector maps provided with the product. You can switch the application to off-road mode from the Navigation menu. Tap , and then , . Most of the procedures described for on-road navigation also apply to off-road navigation.
5 Reference Guide On the following pages you will find the description of the different concepts and menu screens of the software. 5.1 Concepts 5.1.1 Smart Zoom Smart Zoom provides much more than just a usual automatic zoom feature: While following a route: when approaching a turn, it will zoom in and raise the view angle to let you easily recognize your maneuver at the next junction.
Maneuver restrictions and directional constraints are taken into account when planning a route. Roads are used only if access for cars is allowed. Private roads and resident-only roads are used only if they are inevitable to reach the destination. Walkways are excluded from routes. : All maneuvers are available in intersections. Directional constraints are taken into account the way that opposite direction is allowed with a low speed.
5.1.3 Green routing Route calculation is not only about finding the quickest or shortest route. For some of the vehicle types, you can also check the fuel consumption and CO 2 emission when planning a route, and you can create cost effective routes with less effect on the environment. In Route settings, you can edit the parameters of the selected vehicle. Enter the fuel consumption values and the price of the fuel.
5.1.4 Speed limit warning Maps may contain information about the speed limits of the road segments. The software is able to warn you if you exceed the current limit. This information may not be available for your region (ask your local dealer), or may not be fully correct for all roads in the map. Speed warning can be fine-tuned in Sound and Warning settings. You can set the relative speed above which the application initiates the warning.
Button Description Tap this button to get information about the current location and to find nearby help. Tap this button to open the GPS Information screen with satellite position and signal strength information. If you save your trip logs when you arrive at some of your destinations or let the application automatically save the trip logs for you, those logs are all listed here. Tap one of the trips to see the trip statistics, speed and altitude profile.
5.3 Settings menu You can configure the program settings, and modify the behavior of the software. In the Navigation menu, tap . The Settings menu has several options. Tap or scroll with your finger to see the full list. Button Description Adjust the sound volume, mute your device or change the voice guidance language. In addition, you can enable and set up different warnings and alerts. Enable different sounds and alerts in the application. These settings determine how routes will be calculated.
The About section provides you with product information. Read the Software and Database End User License Agreement, or check the map and other contents of the application. You can also access program usage statistics. 5.3.1 Sound and Warnings Adjust the sound volume, mute your device or change the voice guidance language. In addition, you can enable and set up different warnings and alerts. Button Description Tap this button to adjust the volume of the different sounds in the application.
Maps may contain information about the speed limits of the road segments. The software is able to warn you if you exceed the current limit. This information may not be available for your region (ask your local dealer), or may not be fully correct for all roads in the map. This setting lets you decide whether you wish to receive visible and/or audible warnings. Adjust the slider to set the relative speed above which the application initiates the warning.
5.3.2 Route settings These settings determine how routes will be calculated. Button Description You can set the type of vehicle you will use to navigate the route. Based upon this setting, some of the road types can be excluded from the route, or some of the restrictions may not be taken into account in route calculation. You can edit the parameters of the selected vehicle profile, or you can even create new vehicle profiles if you tap More.
Vehicle profiles: When you first tap options: , you see the list of default vehicle profiles. You have the following Button Description You can edit the parameters of the vehicle profile. Tap this button to reveal the below options. Tap this button to create your own vehicle profile. Tap this button to reset all vehicle profiles to their default settings. When creating a new vehicle profile, first you need to select the vehicle type. Then you need to set the following parameters.
Maneuver restrictions and directional constraints are taken into account when planning a route. Roads are used only if access for cars is allowed. Private roads and resident-only roads are used only they are inevitable to reach the destination. Walkways are excluded from routes. : All maneuvers are available in intersections. Directional constraints are taken into account the way that opposite direction is allowed with a low speed.
Gives a quick but fuel efficient route based on the fuel consumption data given in Route settings (page 70). Travel cost and CO2 emission calculations are estimations only. They cannot take elevations, curves and traffic conditions into account. Results in a route with fewer turns and no difficult maneuvers. With this option, you can make your software to take, for example, the freeway instead of a series of smaller roads or streets. 5.3.3 Map settings You can fine-tune the appearance of the Map screen.
Replace the default position marker to one of the 3D vehicle models. You can select separate icons for different vehicle types selected for route planning. Separate icons can be used for car and the other vehicles. Show or suppress 3D landmarks, 3D artistic or block representations of prominent or well-known objects. (optional) Show or suppress 3D city models, 3D artistic or block representation of full city building data containing actual building size and position on the map.
Whenever adequate information is available, lane information similar to the real ones on road signs above the road is displayed at the top of the map. You can turn this feature on or off. If you are approaching a freeway exit or a complex intersection and the needed information exists, the map is replaced with a 3D view of the junction. You can turn this feature on or let the map be displayed for the whole route. When entering tunnels, the surface roads and buildings can be disturbing.
5.3.5 Regional settings These settings allow you to customize the application for your local language, measurement units, time and date settings and formats, as well as to choose the time zone. Button Description This button displays the current written language of the user interface. By tapping the button, you can select a new language from the list of available languages. The application will restart if you change this setting; you are asked to confirm this.
5.4 Trip monitor If you save your trip logs when you arrive at some of your destinations or let the application automatically save the trip logs for you, those logs are all listed here. Tap one of the trips to see the trip statistics, speed and elevation profile. If track log has also been saved, you can display it on the map with the selected color. Track logs can be exported to GPX files for later use. The Trip monitor can also be accessed from the Information menu.
6 Glossary 2D/3D GPS reception The GPS receiver uses satellite signals to calculate its (your) position and needs at least four signals to give a three-dimensional position, including elevation. Because the satellites are moving and because objects can block the signals, your GPS device might not receive four signals.
Route A sequence of route events, i.e. maneuvers (for example, turns and traffic circles) to reach the destination. The route contains one start point and one or more destinations. The start point is the current (or last known) position by default. If you need to see a future route, the start point can be replaced with any other given point. Heading-up map orientation In this mode the map is rotated so its top always points in the current driving direction.
7 Copyright note The product and the information contained herein are subject to change without prior notification. This manual may not, in whole or in part, be reproduced or transmitted in any form either electronically or mechanically, including photocopying and recording, without the express written consent of Alpine Electronics, Inc. © 2015 – Alpine Electronics, Inc. All rights reserved. © 2015 – NNG Kft. All rights reserved. © 2015 HERE. All rights reserved. See http://corporate.navteq.
HERE Maps Update Registration Card INE-W960_NAVICARD M3544194010
It's important to keep your map up-to-date. Register now and we will keep you informed of map updates and special offers. To register, complete and return this card or visit here.com Please tick the box ~Email ok' if you would like to receive information by email. here.com © 2014 HERE All rights reserved. Part No. T1000-22235.
Model No.
NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO.
Thank you for choosing Alpine for your car audio equipment needs. Our goal is to produce the best audio/video/navigation products in the world and hope your expectations are met. Please take a moment to protect your purchase by registering your product now at the following address: www.alpine-usa.com/registration. You will be informed of product and softwareupdates (if applicable), special promotions, and news about Alpine.
