HIGH-RESOLUTION WIRELESS DIGITAL SOUND PROCESSOR PXE-X09
Contents Operation Instructions Warning.......................................................1 Attention......................................................1 Important Instructions..................................1 Precautions Function List................................................2 List of Accessories......................................2 Introduction to the DSP 1. Connections of the DSP..........................3 2. Introduction to the Connectors and Functions.................................
Operation Instructions Warning Warning This symbol is intended to alert you. It may cause serious injury or death if neglected by you. Please immediately stop using the product if any problem occurs. Please send the product to the designated Alpine dealers or nearby Alpine service centers for repairing. Do not use any functions that may divert your attention when driving. Only use such functions that distract you when the car stops.
Precautions You can use PXE-X09 mobile phone app or PC software to tune and set up the PXE-X09. The control with the two methods differs slightly and thus will be discussed in different chapters.
Introduction to the DSP 1.
2. Introduction to the Connectors and Functions 1 Power Connector +12V REM OUT ACC GND 2 Input selection switch When the switch is turned to “ACC”, the DSP will be started by ACC; when the switch is turned to “HOST”, the DSP will be started by high level input signal IN-1. 3 4 5 6 7 8 9 10 High and low level mixed input Connectors The high or low level inputs can be set through the wired controller, PC or mobile phone app.
Mobile Phone App Mobile Phone App Instructions For iPhone users, search and download PXE-X09 Tuning App from App Store; for Android users, please scan the QR code on the cover, download and installed the app. After the PXE-X09 app is installed, start PXE-X09. Open “Settings” → “Turn on Bluetooth” → “Search Devices” → “DSP-HD-...” from your mobile phone and click to connect. Or directly start the app to search Bluetooth automatically, and click to connect “DSP-HD-...
Mobile Phone App e. Select “Shutdown delay” to set the shutdown delay. The range of the shutdown delay: 0-255s. f. Select “Configuration wizard” to enter the wizard for configuring the main sound source, input mode, and output mode. g. Select “Lock” to enter a 6-digit password to encrypt the tuned sound effect data. Click “Unlock” to enter the correct password to decrypt the locked data. The initial password is “888888”. h. Select “Share effect” to share a sound effect or all sound effects. i.
Mobile Phone App (10) (11) (12) (13) Front Left and Front Right channels of IN 3 and 4 are set to Mid-bass; Rear Left and Rear Right channels of IN 5 and 6 are set to Full-range; IN 7 is the center channel and set to Full-range; In 8 is set to Subwoofer.
Mobile Phone App 2. Low level input selection: (1) Stereo (2CH): Front Left and Front Right channels of IN 1 and 2 are set to Full-range. (2) Four-CH (4CH): Front Left and Front Right channels of IN 1 and 2 are set to Full-range; Rear Left and Rear Right channels of IN 3 and 4 are set to Full-range. (3) Six-CH (5.
Mobile Phone App 4. Four-CH + Left and Right (6CH): Front Left and Front Right channels of OUT 1 and 2 are set to Full-range; Rear Left and Rear Right channels of OUT 3 and 4 are set to Full-range; Left and Right channels of OUT 5 and 6 are set to Subwoofer. 5.
Mobile Phone App 14. 15. 16. 17. 10 Rear Left and Rear Right channels of OUT 9 and 10 are set to Subwoofer; OUT 11 is the center channel and set to Full-range.
Mobile Phone App There are 10 input EQ values. Move the slider up and down or click a gain value to display the gain adjustment box and then move the slider left and right or press “+”/“-” to set the gain; click a Q value to display the Q value adjustment box and then move the slider left and right or press “+”/“-” to set the Q value; click a frequency value to display the frequency adjustment box and then move the slider left and right or press “+”/“-” to set the frequency.
Mobile Phone App Setting the Master Volume and Sound Source Setting the Delay Click the delay button “ signal delay. ” to set the output 1. Delay unit: ms, cm, in; Delay range: 0.000-20.000 ms; 0-692 cm; 0-273 in. 2. Click the icon to display the delay setting box, and then move the slider left and right or press “+”/“-” to set the delay. Sound Effect Presets The DSP provides a storage space for 6 groups of sound effect presets for storing and loading sound effect data.
Software for PC Software Instructions Important Instructions for Software Installation ●● The software can only run on Microsoft® Windows® platforms. Recommended specifications Operating system: Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10 CPU: 1.6 GHz or higher Memory: 1 GB or higher Hard disk: 512 MB or more PC resolution: 1280*768 or higher ●● Before connecting PXE-X09 to PC, please install the PXE-X09 software correctly.
Software for PC Figure 2 Connecting to the DSP 1. Before the DSP is connected, the connection icon is in red “ ”; after it is connected, the connection icon is in green “ ”. 2. Menu area: File, Option and Lock d. (1) Click “File”: e. (2) a. a. Select “Load PC Presets File”: load the preset file previously saved on your PC as the current working scenario of the DSP; b. Select “Save as PC Presets File”: Save the current working scenario data of the DSP on your PC for future use; c.
Software for PC c. Select “Input link settings” to set the function to be tuned. There are five options: Channel EQ, X-Over, Channel phase, Channel volume, and Channel mute. d. Select “Output link settings” to set the function to be tuned. There are six options: Channel EQ, X-Over, Channel delay, Channel phase, Channel, volume and Channel mute. e. Select “Advanced” to turn the flow lamp on or off. The range of the shutoff delay: 0 - 255s. f.
Software for PC (4) Four-CH + Left and Right FC (6CH): Front Left and Front Right channels of IN 1 and 2 are set to Full-range; Rear Left and Rear Right channels of IN 3 and 4 are set to Full-range; Left and Right channels of IN 5 and 6 are set to Subwoofer.
Software for PC Rear Left and Rear Right channels of IN 9 and 10 are set to Subwoofer; IN 11 is the center channel and set to Full-range. (14) Three Front Channels + Rear Channels + FC (9CH): Front Left and Front Right channels of IN 1 and 2 are set to Tweeter; Front Left and Front Right channels of IN 3 and 4 are set to Midrange; Front Left and Front Right channels of IN 5 and 6 are set to Woofer; Rear Left and Rear Right channels of IN 7 and 8 are set to Full-range; IN 9 is set to Subwoofer.
Software for PC Note: the “Clear all” button is invalid in the customized setting interface. 1. Front Sound Field Stereo (2CH): Front Left and Front Right channels of OUT 1 and 2 are set to Full-range. 2. Four-CH (4CH): Front Left and Front Right channels of OUT 1 and 2 are set to Full-range; Rear Left and Rear Right channels of OUT 3 and 4 are set to Full-range. 3.
Software for PC 12. 13. 14. 15. Front Left and Front Right channels of OUT 5 and 6 are set to Woofer; Rear Left and Rear Right channels of OUT 7 and 8 are set to Tweeter; Rear Left and Rear Right channels of OUT 9 and 10 are set to Woofer; Left and Right channels of OUT 11 and 12 are set to Subwoofer; OUT 13 is the center channel and set to Full-range.
Software for PC 1. Mode setting: Linkwitz-Riley, Bessel and Butterworth. 2. Frequency setting: The frequency can be adjusted by directly entering values, scrolling the mouse wheel, pressing the Up/ Down keys or clicking “H” or “L”, or pressing the left key of the mouse to drag the slider. Adjustment range: 20 Hz–20,000 Hz. 3. Slope setting: Select 6dB/Oct, 12 dB/Oct, 18 dB/Oct, 24 dB/Oct, 30 dB/Oct, 36 dB/ Oct, 42 dB/Oct, or 48 dB/Oct from the dropdown menu.
Software for PC 4. Click “Reset EQ”, all the equalizers of the current channel are reset to the initial state: the frequency is evenly distributed, the input Q value is 2.515, the output Q value is 2.201, and the gain is 0.0 dB. 5. Click “P.EQ”, a warning dialog box appears, indicating “Are you sure you want to switch from the G.EQ mode to the P.EQ mode?”, press “Confirm” to switch to the “P.EQ” mode. Click “G.EQ”, a warning dialog box appears, indicating “Are you sure you want to switch from the P.
Software for PC Sound Effect Presets Loading and storage of sound effect presets. Click “Call” or “Store” to set the six sound effect presets. Coaxial, Bluetooth, High Level, Low Level, and Off. Note: W hen a sound source is selected, it cannot then be selected again as the auxiliary sound source; doing so causes the auxiliary sound source to be invalid. Optical and Coaxial cannot be selected at the same time.
Wired Controller Instructions for the Use of the Wired Controller This wired controller only applies to PXE-X09. Connect the wired controller correctly to the DSP and make sure it is started normally before use. Startup Screen Figure 3 After the wired controller is started, the dynamic startup screen appears, as shown in Figure 1. After selecting the main sound source, press the button briefly to enter the Mix Source interface, as shown in Figure 4-1.
Wired Controller Subwoofer Volume (SUBW) After selecting the mix sound source, press the button briefly to enter the Subwoofer volume (SUBW) interface, as shown in Figure 5. Turn the button of the wired controller to adjust the subwoofer volume. Turning it clockwise can increase the volume, while turning it counterclockwise will reduce the volume (the adjustment range is from 0 to 15).
Technical Parameters 1. Technical specifications Dynamic range ≥110dB Signal noise ratio ≥100dB Noise floor ≤32uVrms Channel separation ≥110dB Total harmonic distortion ≤0.
2. Functional parameters Input signal 16-Channel RCA/High level mixed input, Optical/Coaxial/Bluetooth signal input Output signal 16-Channel RCA audio signal output Input/output signal gain Range: mute, 0-35 Mode: Graphic EQ and Parametric EQ Input/output signal EQ Frequency: 20 Hz–20 kHz, resolution 1 Hz Q value (slope): 0.404-28.852 Gain: -12 dB to +12 dB, resolution 0.1 dB Each input/output channel has at most 8 independent filters.
Harmful Substances Name and content of harmful substances contained in the product Poisonous or harmful substances or elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent chrome (Cr(VI)) Circuit board components × О О О О О Enclosure components О О О О О О Display components × О О О О О Accessories × О О О О О Part name Polybrominated Polybrominated biphenyl diphenyl ether (PBB) (PBDE) This table is prepared in accordance with SJ/T11364.
.ffeff/lLPINE. LIMITED WARRANTY ALPINE ELECTRONICS OF AMERICA, INC. ("Alpine"), is dedicated to quality craftsmanship and is pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below. ePRODUCTS COVERED: This Warranty covers Car Audio Products and Related Accessories ("the product"). Products purchased in the Canada are covered only in the Canada.
#/#ALPINE~ GARANTIE LIMITEE Fidele a son engagement de ne fournir que des produits de qualite, ALPINE ELECTRONICS OF AMERICA, INC. («Alpine») est heureuse de vous offrir cette garantie. Nous vous suggerons de le lire attentivement et en entier. Si vous avez la moindre question, veuillez contacter l' un de nos concessionnaires ou appeler directement Alpine aux numeros listes cidessous.
