IMPORTANT-Please read and follow all warnings and instructions before using this product.Injury can result from improper use.Save this documents. SHOWER DOOR INSTALLATION INSTRUCTIONS 0.24" 0.125" WARNING Tempered Glass, please don't hit the corners and the surrounding,otherwise the glass will burst. General Information SD80148-BP-BN/MB/BG SD80160-BP-BN/MB/BG SD80164-BP-BN/MB/BG www.altairdesignusa.
Detailed Diagram of shower door components Parts List: 1xInstallation Instruction. [1] 5xWall Plugs. [2] 4xScrews ST4x35. [3] 2xWall Connectors. [4] 2xTop Wheels. [5] 1xDoor Panel. [16] [6] 2xHandle Sets. [7] 2xAnti-collision Components. [8] 2xTop Rollers. [9] 1xTop Horizontal Rail. [10] 1xDoor Guider. [11] 1xScrew ST4x25. [12] 1xScrew Cover Cap. [13] 1x Bottom Horizontal Rail. [14] 2x Cover Caps. [15] 4xDoor Side Gaskets. [16] 1xDoor Panel.
5 WARM TIPS 01: Open the packaging care fully and inspect all the necessary parts using detailed diagram and component list in your manual as a reference. Before discarding the carton, check for small hardware bags the tend to fall to the bottom of the box. If any parts are damaged or missing, please contact us for replacement. 6 [9] x1 02: Retain these installation instructions for future use if in need. 1.Measure the distance between two finished walls. This distance is marked as W.
7 03 8 04 2.66" Top view [1] x4 [9] [2] x1 x4(ST4x35) [3] 71.575" x2 1 2 [9] [3] 1 2 [1] 3 4 [2] [3] 0.24" [3] 4.Remove the covers of the Wall Connectors[3], stick the two ends of the Top Horizontal Rail[9] in the Wall Connectors[3]. Recover and fasten the covers with Allen Key. Please see Fig 1&2&3 for details. 3.Measure a distance of 71.575" from the shower tray or threshold to Wall Connectors[3], and mark the holes' position for Wall Connectors[3].
9 10 05 06 [8] [8] [7] x2 [4] [16] [7] x2 [8] [5] x2 Outside [5] [16] [4] [16] [5] Outside Outside x1 x1 [13] [10] [5] [4] Inside 5. Install the Top Rollers[8] into the two predrilled holes of the Door Panel[16]. Place the bottom of Door Panel[16] into the gap between the Door Guide[10] and Bottom Horizontal Rail[13], and insert the top of Door Panel[16] into the slot of Top Horizontal Rail[8]. Install the Anti-collision Component[7] into the hole of Door Panel[16],lock and fasten it.
11 12 07 08 [6] [1] x1 x2 1 [10] [15] x1 [11] x1(ST4x25) x4 [6] [12] 2 8. Install the Handle Set[6] onto the Door Panels[5&16], lock and fasten them with Allen Key. Please see Fig 1 for details. x1 [13] x1 2 [3] Please ensure the bottom horizontal is straight before drilling 0.24" 7.Stick the Door Guider[10] onto the Door Panel[5]. Level the Bottom Horizontal Rail[13], and align the hole position of Bottom Horizontal Rail with the hole position of Door Guider[10].
13 14 09 10 2 [14] 1 x2 [14] [5] [4] [13] Inside [16] [8] 2 10. Apply thin beads of glass glue into the Cover Caps[14], and assemble them on both ends of the Bottom Horizontal Rail[13]. Outside 9.If there is a seam when the door is closed like the picture in the right, use Wrench to adjust the Top Wheel[4] or the Top Roller[8] till there is no seam any more. Please see Fig 1&2 for details.
