WBP-210 SINGLE CHANNEL WIRELESS BELTPACK WB-200 SERIES WIRELESS INTERCOM SYSTEM OWNERS MANUAL ISSUE 29J10 AUDIO ELECTRONICS DESIGN EQUIPOS EUROPEOS ELECTRÓNICOS, S.A.L Avda. de la Industria, 50. 28760 TRES CANTOS-MADRID (SPAIN). 34-91-761 65 80 34-91-804 43 58 www.altairaudio.com altair@altairaudio.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 2 1. INTRODUCTION.........................................................................................................................................3 2. SWITCHES, CONTROLS, ADJUSTMENTS AND CONNECTORS....................................................................4 2.1 UPPER PANEL..........................................................................................................................................................4 2.2 FRONT PANEL........
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 3 1. INTRODUCTION Congratulations on your purchase of the ALTAIR single channel wireless beltpack WBP-210 of the WB-200 series wireless intercom system. There are a lot the characteristics that make of the ALTAIR WB-200 series one of the most highlighted in the audio professional market, some are enumerated here: Dual pre-amble diversity antenna system detects and selects the higher radio signal ensuring better coverage and minimum dropouts.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 2. SWITCHES, CONTROLS, ADJUSTMENTS AND CONNECTORS Switches, controls, adjustments and connectors that you can find in your ALTAIR intercom beltpack. The description and explanation of each one will be found in the corresponding section. 2.1 UPPER PANEL - MIC SWITCH. - UPPER VOLUME UP/DOWN SWITCHES. 2.2 FRONT PANEL - CALL SWITCH. - OLED DISPLAY. - MENU SWITCH. - SELECT SWITCH. - ON/OFF SWITCH. - FRONT VOLUME UP/DOWN SWITCHES. 2.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 5 3. OPERATION The WB-200 series intercom system are designed to allow maximum easy communications operation between the different control areas in music or theatre live performances, television, cinema, conference halls, and whatever broad events where multiple and fast communications are required, by means of its simultaneous listening-speaking operation system.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 6 3.2 MIC ON/OFF/PUSH TO TALK SWITCH (TALK) The MIC switch allows to enable/disable the microphone, so that we are able to speak with other units connected to the same intercom channel. If the microphone is activated, its associated LED will light up and this icon, will show in the display: ,and on the other hand, if it is disabled, its associated LED will turn off and will not show the icon in the display. The MIC switch has two operation modes.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 7 with the wireless beltpack that is calling at this time (if the call is from the base station does not indicate any number associated), if the vibrator is enabled (see vibrator on/off section for more information) will be vibrate, and if the buzzer is enabled (see buzzer on/off section for more information) an intermittent sound will take place during about three seconds. 3.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 8 If the microphone phantom power is enabled, this icon: appears near to the microphone icon . When using electret type mics, MIC level must be set to around 5 steps higher than minimum position as general recommendation. Set also the SIDE TONE setting accordingly. The state of the microphone phantom power, it is stored in the unit. FACTORY PRESET: OFF (Dynamic mic.) 3.6.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 3.6.7 CHANGING THE BELTPACK NAME With the Name MENU, the user can change the beltpack name that appears on the display , under the beltpack registration number, this name has 7 characters, selected by the user. FACTORY PRESET: ALTAIR1. 3.6.8 OLED CONTRAST ADJUSTMENT The display contrast can be changed using this menu, between the values 1 and 10, to adapt to different ambient light conditions.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 10 lock the keys configured in the keyboard lock configuration (see section 3.6.10) TOP Panel, FRONT panel or all. The keyboard lock can be enabled via the appropriate menu, or directly without accessing the beltpack menu, pressing the ON/OFF switch, and at the same time the MIC ON/OFF switch (changing the vibrator state, if it is on, turn to off mode and if the vibrator it is turned off, turn to on mode).
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 11 If we pressed key REGISTER again the function will be reset.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 12 3.8 SELECT SWITCH This switch , in normal mode, enables/disables the buzzer sound when the unit receives a call and when the user press a key. Whenever this switch is pressed, and the buzzer is enabled, it will be disabled, and the LED indicator will turn off. On the other hand, if the buzzer was disabled, it will be enabled and the LED indicator will lighten up, and appears this icon in the display.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 13 4.1 AUXILIARY BATTERY The wireless beltpack has a battery holder to place an alkaline battery, Ni-MH battery 2500 mA/h or lithium battery of AA size, which gives us a range of 3/4/5 hours respectively with the main battery discharged. Be very careful, do not insert the battery in reverse polarity, as it may break the circuitry of the wireless beltpack. Always remember to remove the empty battery. 4.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 14 6. TROUBLESHOOTING GUIDE WHEN: 1) Abnormal low range. POSSIBLE CAUSES AND SOLUTIONS a) With the beltpacks on, switch off the base station, wait for 30 seconds and then switch on to reorganize links. 2) Beltpack switch on but does a) Beltpack is not registered. If the base station have free registers, register it not link with the base station. normally. b) If you have more than a system it is possible that this beltpack correspond to another system.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 15 7. BATTERY CHARGER ALTAIR WBPC-210 The battery charger ALTAIR WBPC-210 allows to charge up to four beltpacks ALTAIR WBP-210 simultaneously. The charge time is approximately of four hours with the batteries totally discharged. 7.1 CHANGING THE FUSE The battery charger ALTAIR WBPC-200 is set to operate from 100 VAC, 50-60Hz to 240VAC, 50-60Hz. Make sure that the unit is disconnected of the mains.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 16 7.3 BELTPACK BATTERY CHARGE The battery charger ALTAIR WBPC-210 has four connectors to allow the charge up to four wireless beltpacks at the same time. Take any of the battery charger connector and insert it in a wireless beltpack connector. If the battery charger is connected, the connector associated LED of the battery charger will change from green to orange, indicating that the wireless beltpack batteries are charging.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 17 8. TECHNICAL SPECIFICATIONS PREAMPLIFIER MICROPHONE TYPE: INPUT IMPEDANCE: NOMINAL LEVEL: PHANTOM VOLTAGE: • • • • Dynamic or electret. 4K7. -45 dBu. +9 VDC (internal preset ). 200 Ω (nominal), 2KΩ (maximum). OUTPUT POWER: • • • FREQUENCY RESPONSE: • HEADSET AMPLIFIER IMPEDANCE: MAXIMUM LEVEL: 14 Vpp (200 Ω). 200 mW (200 Ω). 250 Hz - 3500 Hz. RADIO FREQUENCY: MODULATION: TRANSMIT POWER: RECEIVE SENSITIVITY: • 1900 MHz band.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK 9. WARRANTY This unit is warranted by Equipos Europeos Electrónicos to the original user, against flaws in the manufacturing and in the materials, for a period of two years (one year depending on some countries), starting from the date of sale. Flaws due to wrong use of the unit, internal modifications or accidents, are not covered by this warranty. There is no other warranty expressed or implicit. Any faulty unit must be sent to the dealer or the manufacturer.
WBP-210 SINGLE CHANNEL WIRELESS BELTPACK European Union Waste Electronics Information Unión Europea Información sobre residuos electrónicos Waste from Electrical and Electronic Equipment (WEEE) directive The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling, contact your local sales office.