Altec Lansing Moondance Home Digital Speaker System and Alarm Clock for iPod® M302 User Guide
Welcome FCC Compliance Thank you for purchasing the Altec Lansing Moondance Home speaker system. Designed specifically to work with your iPod, this system provides high-quality audio and radio performance that brings out the best in your music. This Altec Lansing speaker system is designed to work with: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Safety Information The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Caution: To prevent the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel.
Contents Welcome.................................................................................................................................................................................................. ii Safety Information................................................................................................................................................................................... 1 Package Contents..................................................................................
Package Contents User Guide and Quick Connect Instructions Altec Lansing Moondance Home speaker system Wireless remote Miscellaneous adapters for iPod AC adapter FM radio antenna 3
Getting Started How to Install the AC Adapter 1 Connect the AC adapter cable plug into the speaker system’s power jack. The jack is located on the back of the system and labeled POWER. 2 Plug the AC adapter into a wall outlet. How to Install the Wireless Remote Battery The wireless remote battery (included) is not installed at the factory. To install the battery, follow these steps: 1 Open the battery compartment door. The battery compartment door is located on the back end of the remote.
Placing and Removing Adapters for the iPod Your Altec Lansing Moondance Home speaker system includes removable adapters for today’s popular iPod models. These adapters ensure that your iPod properly fits in the speaker system’s dock. As new iPod models are introduced, new adapters will be made available to customers. You may also use the adapters supplied with your iPod or available for purchase at www.apple.com. How to Place an Adapter 1 Select the correct adapter for your iPod.
Speaker Features and Indicators Universal docking station for iPod Snooze/LCD brightness increase button Snooze/LCD brightness decrease button Source button Alarm 2 button Sleep button Alarm 1 button Standby button Time button Volume increase button LCD display Volume decrease button Power jack Auxiliary input connector FM FM antenna 6 AUX IN POWER
Speaker Controls Turn on your speaker system Ensure the AC adapter is connected to the system and plugged into the wall. See the Getting Started section for more information. Momentarily press the STANDBY button. Increase LCD display brightness Press the button to brighten the LCD display. Decrease LCD display brightness Press the button to dim the LCD display. Press the SOURCE button to cycle through and select the audio source: iPod, FM or AUX.
Speaker Controls 8 Set the time See the Setting the Clock Display section for detailed instructions on setting the clock. Set the alarms See the Setting the Alarm section for instructions on setting the alarms. Dismiss the alarm Press either the ALARM1 or ALARM2 button when the alarm is sounding. Snooze for 5 minutes Press the Sleep See the Setting the Sleep Timer section for more information on the SLEEP button. or button when the alarm is sounding.
Wireless Remote Features The wireless remote lets you operate many functions of your Altec Lansing Moondance Home speaker system: Turn on your speaker system Change audio source Momentarily press the button. Press the SOURCE button to cycle through and select the audio source: iPod, FM or AUX. NOTE If you are in “FM” or “AUX” mode and you dock your iPod, the speaker system will automatically change to “iPod” mode.
Wireless Remote Features Fast-forward the currently playing track on your iPod In “iPod” mode, press and hold the Tune radio stations and buttons. In “FM” mode, use the See the Listening to the Radio section for additional information. Seek radio stations or In “FM” mode, press and hold the button. See the Listening to the Radio section for additional information. Automatically tune and save all clear FM Press and hold the AUTO button on the wireless remote for 3 seconds.
Listening to Your iPod 1 Dock your iPod in the Altec Lansing Moondance Home speaker system. 2 Ensure your speaker system is powered on Charging Your iPod Whenever your iPod is docked and your Altec Lansing Moondance Home speaker system is plugged into an AC outlet, your iPod is charging (until fully charged) – even if the speaker system is switched off. If the system isn’t on, press the STANDBY button on the speaker system or the button on the wireless remote.
Listening to the FM Radio 1 Plug the FM radio antenna into the speaker system’s FM ANTENNA jack. The jack is located on the back of the system. 2 Extend the FM antenna wire fully for best FM reception. Also, do not strip, alter or attach to other antennas. 3 Ensure your speaker system is powered on. If the system isn’t on, press the STANDBY button on the speaker system or the button on the wireless remote.
Listening to a Non-docking iPod or Other Portable Audio Device If you have a non-iPod MP3 player or other non-docking portable audio device, you can enjoy it through your Altec Lansing Moondance Home speaker system as well. Just connect it via the AUX IN jack. Here’s how: 1 Locate a 3.5 mm stereo cable (not included). 2 Plug one end of the stereo cable into your device. Your device should have either a headphone or LINE OUT jack for you to plug into. 3 7 Adjust the volume.
Setting the Clock Display How to Set the Clock Time and Date 6 Set the date. and buttons on your speaker system or the Use the VOLUME + and – VOLUME buttons on the wireless remote to select the date. Press the TIME button to save this setting and enter the Hour Set mode. 1 Ensure your speaker system is powered on. 7 and buttons on your speaker system or the Use the VOLUME + and – VOLUME buttons on the wireless remote to adjust the hour.
Setting the Alarm Your Altec Lansing speaker system has two separate alarms. VOLUME + and – VOLUME buttons on the wireless remote to set the alarm volume. Then press the ALARM1 button to save this setting and enter the Alarm Source mode. How to Set Alarm 1 6 1 2 Press and hold the ALARM1 button for 3 seconds. This puts you in the Alarm Set mode for alarm 1. 3 Adjust the hour.
Setting the Alarm 8 Exit the Alarm Set mode. How to Use Alarm 1 Press the ALARM1 button on the speaker system or the ENTER button on the wireless remote to exit the Alarm Set mode. The speaker system will also automatically exit the Alarm Set mode after 5 seconds of inactivity. NOTE When exiting the Alarm Set mode, the alarm is automatically turned on. To turn off the alarm, press the corresponding ALARM1/ALARM2 button.
Setting the Sleep Timer Your Altec Lansing speaker system is equipped with a sleep timer that automatically turns off the unit 30, 60, 90 or 120 minutes after it has been set. How to Set the Sleep Timer 1 Maintaining Your Speaker System Place your speaker system on a level surface away from sources of direct sunlight or excessive heat. Protect your furniture with a cloth or other protective material when placing your speaker system on a natural wood or lacquered finish.
Troubleshooting Symptom Possible Problem Solution Plug the AC adapter into a wall outlet and plug the connector into the power supply jack on the back of the speaker system. Speaker system doesn’t respond (no power) AC adapter isn’t plugged into a wall outlet or the connector isn’t plugged into the power supply jack on the back of the speaker system Wall outlet is not functioning Plug another device into the same outlet to confirm the outlet is working.
Troubleshooting Symptom Possible Problem Solution iPod is not installed properly Remove your iPod from the dock and check for obstructions on the connectors in the dock and on your iPod. Then reseat it in the dock. iPod is locked up Please make sure your iPod is working properly before docking into the unit. Please refer to your iPod manual for details.
Warranty Altec Lansing Technologies, Inc. One-Year Limited Warranty (Two-Year Limited Warranty In the European Union and Asia) must be accompanied by the original proof of purchase. You should insure the shipment as appropriate because you are responsible for the product until it arrives at Altec Lansing. What Does the Warranty Cover? How Will State Law Affect Your Rights? Altec Lansing warrants that its products shall be free from defects in materials or workmanship, with the exceptions stated below.
www.alteclansing.com Headquarters Europe 535 Rte. 6 & 209, Milford, PA 18337-0277 • 800-ALTEC-88. 570-296-4434. • Fax 570-296-6887 13 Rue Beaumont, L-1219 Luxembourg, Luxembourg Asia/Pacific 23/F, Office Tower, Shun Hing Square Diwang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen, China 518008 “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards.