User guide
Table Of Contents
- About This Manual
- Overview
- Technology Enhancements in Release 5.1
- SIP Implementation
- Multi-Site Enterprise Management - AltiEnterprise Manager
- Multi-Chassis Gateway Support (ACM only)
- Capacity Improvements
- Voice Processing New Features and Enhancements
- PBX New Features and Enhancements
- Call Center New Features and Enhancements
- Client Application New Features and Enhancements
- IP Phone New Features and Enhancements (IP600, IP710, IP705)
- Key System Features
- Technology Enhancements in Release 5.1
- Software Installation & License Registration
- Getting Around AltiWare Administrator 5.1
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Country-Relevant Settings
- Audio Peripheral Configuration
- Activity
- Feature Profiles
- CT-Bus Configurations
- Voice Mail Configuration
- Auto Attendant Configuration
- Board Configuration
- Using the Triton Resource Board
- Using the Triton MeetMe Conference Board
- Configuring the Quantum Board
- Configuring the Triton Analog Station Board
- Configuring the Triton Analog Trunk LS/GS and LS Boards
- Configuring the Triton VoIP Board
- Configuring the Triton T1/E1 Board
- Configuring Virtual Boards SIPSP and H323SP
- Configuring the MAX Board
- Configuring the Virtual MobileExt Board
- Trunk Configuration
- Trunks Out of Service
- Channel Identification
- Opening the Trunk Configuration Window
- Selecting Trunks to Set Attributes
- Configuring One or Multiple Trunks
- Setting General Trunk Attributes
- H323 Tie Trunk Properties
- SIP Tie Trunk Properties
- SIP Trunk Properties
- Triton T1/E1 Trunk Properties
- Triton Analog Trunk GS/LS Properties
- Quantum Trunk Properties
- Incoming Call Routing
- Outgoing Call Blocking
- In Call Routing Configuration
- Out Call Routing Configuration
- Extension Configuration
- Setting Up IP Extensions
- AltiGen IP Phone Configuration
- Mobile Extension Configuration
- Hunt Group Configuration
- Paging Group Configuration
- Line Park Configuration
- Workgroup Configuration
- Managing and Using MeetMe Conference
- Network Configuration Guidelines for VoIP
- Enterprise VoIP Network Management
- Understanding VoIP Bandwidth Requirements
- Opening AltiEnterprise Manager
- Setting VoIP Codec Profiles
- Assigning Codec Profiles to IP Addresses
- Defining IP Networks
- Defining the IP Dialing Table
- The Multi-site VoIP Domain
- Working with Servers in the VoIP Domain
- Managing VoIP Domain Users
- Configuring Global Least Cost Routing
- When Information May Be Out of Sync
- System Report Management
- Tools and Applications
- E1-R2 and E1 ISDN PRI Installations
- Required Service Parameters
- Network Ports
- Technical Support & Product Repair Services
- Troubleshooting
- Index
80 AltiWare ACC 5.1 Administration Manual
Configuration
Double-click the TritonIP board in the Boards window to open the Board Configuration
window, similar to Figure 2 on page 76. See attribute descriptions below Figure 2. Note
the following additional information:
• Clicking the Board Configuration button opens a window that displays the board
serial number, DSP clock, and physical and logical IDs. The drop-down list in the
Configure Type field lets you select between a 12-port G.711/G.723/G.729
configuration and a 30-port G.711 configuration.
Figure 5. Board Configuration window
Configuring the Triton T1/E1 Board
Through AltiWare Administrator, the Triton T1/E1 board can be configured for either
digital T1 CAS (channel associated signaling), T1 PRI (Primary Rate Interface), E1 CAS,
or E1 PRI.
Both T1 CAS and T1 PRI carry 24 channels using time-division multiplexing (TDM) at an
overall rate of 1.544 Mbps. Voice T1 provides 24 64K channels with robbed bit signaling.
T1 PRI provides 23 64K channels, using one 64K channel for D channel messaging.
E1 CAS and E1 PRI carry 32 channels using TDM at an overall rate of 2.048 Mbps. Both
of them provide 30 64K channels for voice.
To subscribe to T1 CAS, T1 PRI, E1 CAS, or E1 PRI service, you must supply certain
parameters. These parameters are listed in Appendix B on page 335.
Configuring the Board
Double-click the Triton T1/E1 board in the Boards window to open the Board
Configuration window, similar to Figure 2 on page 76. See attribute descriptions below
Figure 2. Note the following additional information:
• The Board ID must be in the range 0–7.
• Double-click a channel in the Channel Mapping List to open a trunk configuration
dialog box.
• Double-click a channel group to open a configuration window, discussed in the
following section.
• Clicking the Board Configuration button opens a configuration dialog box that
displays the board’s serial number, DSP clock, physical and logical IDs.
If you change this configuration,
you must restart the switching
services for the change to take
effect.