User guide
Table Of Contents
- About This Manual
- Overview
- Technology Enhancements in Release 5.1
- SIP Implementation
- Multi-Site Enterprise Management - AltiEnterprise Manager
- Multi-Chassis Gateway Support (ACM only)
- Capacity Improvements
- Voice Processing New Features and Enhancements
- PBX New Features and Enhancements
- Call Center New Features and Enhancements
- Client Application New Features and Enhancements
- IP Phone New Features and Enhancements (IP600, IP710, IP705)
- Key System Features
- Technology Enhancements in Release 5.1
- Software Installation & License Registration
- Getting Around AltiWare Administrator 5.1
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Country-Relevant Settings
- Audio Peripheral Configuration
- Activity
- Feature Profiles
- CT-Bus Configurations
- Voice Mail Configuration
- Auto Attendant Configuration
- Board Configuration
- Using the Triton Resource Board
- Using the Triton MeetMe Conference Board
- Configuring the Quantum Board
- Configuring the Triton Analog Station Board
- Configuring the Triton Analog Trunk LS/GS and LS Boards
- Configuring the Triton VoIP Board
- Configuring the Triton T1/E1 Board
- Configuring Virtual Boards SIPSP and H323SP
- Configuring the MAX Board
- Configuring the Virtual MobileExt Board
- Trunk Configuration
- Trunks Out of Service
- Channel Identification
- Opening the Trunk Configuration Window
- Selecting Trunks to Set Attributes
- Configuring One or Multiple Trunks
- Setting General Trunk Attributes
- H323 Tie Trunk Properties
- SIP Tie Trunk Properties
- SIP Trunk Properties
- Triton T1/E1 Trunk Properties
- Triton Analog Trunk GS/LS Properties
- Quantum Trunk Properties
- Incoming Call Routing
- Outgoing Call Blocking
- In Call Routing Configuration
- Out Call Routing Configuration
- Extension Configuration
- Setting Up IP Extensions
- AltiGen IP Phone Configuration
- Mobile Extension Configuration
- Hunt Group Configuration
- Paging Group Configuration
- Line Park Configuration
- Workgroup Configuration
- Managing and Using MeetMe Conference
- Network Configuration Guidelines for VoIP
- Enterprise VoIP Network Management
- Understanding VoIP Bandwidth Requirements
- Opening AltiEnterprise Manager
- Setting VoIP Codec Profiles
- Assigning Codec Profiles to IP Addresses
- Defining IP Networks
- Defining the IP Dialing Table
- The Multi-site VoIP Domain
- Working with Servers in the VoIP Domain
- Managing VoIP Domain Users
- Configuring Global Least Cost Routing
- When Information May Be Out of Sync
- System Report Management
- Tools and Applications
- E1-R2 and E1 ISDN PRI Installations
- Required Service Parameters
- Network Ports
- Technical Support & Product Repair Services
- Troubleshooting
- Index
Chapter 4: System Configuration
AltiWare ACC 5.1 Administration Manual 69
Configuring Music On Hold and Recorded Announcements
Callers will hear the music or recorded announcement configured on this tab only if the
user places the caller on hold.
To configure music on hold when using audio equipment
1. Check Enable Callers on Hold or in Queue to Listen to Music or Recorded
Announcement.
2. Select the Quantum or Triton Analog Station board number to which the audio
equipment is attached.
To configure music on hold to play a file
1. Make sure a VoIP board is installed (required for playing a file).
2. Check Enable Callers on Hold or in Queue to Listen to Music or Recorded
Announcement.
3. Use the drop-down list to select the logical board ID of the VoIP board.
The system will play the default music-on-hold file when the user places the caller
on hold.
The default music-on-hold file is a .wav file called “MusicOnWaiting.wav”. The file is
located in the C:\PostOffice\phrases\Music folder. You can replace the file with a .wav
file (or an AltiGen PCM file). A .wav file must be in 8 kHz/ 8 bit/ Mono/ u-Law format.
Any optional music-on-hold files included with AltiWare are in that format. You can
convert your own .wav files to this format using Microsoft Windows Sound Recorder.
Note: You may need to reduce the music volume level 70-80% to avoid distortion.
To replace the default music-on-hold file
1. Back up the default file.
2. On the Audio Peripheral tab, uncheck the Enable Callers on Hold or in Queue
to Listen to Music or Recorded Announcement check box.
3. Rename the desired .wav file to “MusicOnWaiting.wav” and put it in the
C:\PostOffice\phrases\Music folder.
4. On the Audio Peripheral tab, check the Enable Callers on Hold or in Queue to
Listen to Music or Recorded Announcement check box.
Note: If you have two files named MusicOnWaiting in the MusicOnWaiting folder, one a
.wav file and one a PCM file, the .wav file takes precedence.