User`s guide

ManualsBrandsAltinex ManualsComputer equipmentAC301-201

CP452

CP452CP452

CP452-

-009

009 009

009 MultiTouch

MultiTouchMultiTouch

MultiTouch™

™™

™

InIn

In-

-Wall Widescreen Panel

Wall Widescreen PanelWall Widescreen Panel

Wall Widescreen Panel

User’s Guide

400-0546-001

2) Align mounting wings

Frame

vertically to insert.

1) Set gap between frame

and wings to larger

than wall thickness.

SCREW

WING

Welcome!

We greatly appreciate your purchase of the CP452-009. We are sure you will

find it reliable and simple to use. Superior performance for the right price,

backed by solid technical and customer support is what ALTINEX has to offer.

We are committed to providing our customers with

Signal Management Solutions

to the most demanding audiovisual

installations at competitive pricing and we welcome you to join the ranks of

our many satisfied customers throughout the world.

1. Precautions and Safety Warnings

Please read this manual carefully and heed all warnings. Keep this manual

handy for future reference. These safety instructions are to ensure the long

life of your CP452-009 and to prevent fire and shock hazards.

1.1 General

• There are no user serviceable parts inside. Qualified ALTINEX service

personnel must perform all service on the CP452-009.

1.2 Installation Precautions

• Place the CP452-009 in a dry area away from dust and moisture.

• To prevent fire or shock, do not expose to water or moisture. Do not place

in direct sunlight, near heaters, or heat-radiating appliances, or near any

liquid. Direct sunlight, smoke, or steam can harm internal components.

• Handle the CP452-009 carefully. Dropping or jarring can cause damage.

• Do not pull any cables that are attached to the CP452-009.

• If not used for an extended period, disconnect from AC power.

1.3 Cleaning

• Unplug the CP452-009 adapter before cleaning and clean only with a dry

cloth. Never use strong detergents or solvents such as alcohol or thinner.

Do not use a wet cloth or water to clean the unit. Do not open the unit to

clean.

1.4 FCC Notice

• This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

• This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions found herein,

may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

• Any changes or modifications to the unit not expressly approved by

ALTINEX, Inc. could void the user’s authority to operate the equipment.

2. Installation Procedures Preparation

Step 1. Make a list of the cabling requirements for the end-user application. What cable types are needed? For

example: CAT-5 for network connection, RS-232 for device control, power, VIDEO, USB, etc.

Step 2. Determine the best location for the touch panel then prepare the cables based on type and length.

Installation - Hardware

Step 3. Use the cutout template provided with the panel to make the opening in the wall. Test fit the panel into

the wall opening. Make sure the mounting wings are aligned vertically and the gap between the frame

and the wing is a little more than the wall thickness before fitting the panel into the wall.

Step 4. Remove the panel and set it aside. Route all cables needed for the installation through the wall opening,

into the wall, and to the proper source/destination. For power, only use the power adapter provided.

Step 5. Once the cables are routed, connect the power cable to the panel and verify the panel turns on

automatically. After the panel boots, disconnect the adapter from AC power.

Step 6. Connect the remaining cables to the panel and insert the panel into the wall. Be careful not to bend the

cable connectors that are attached to the panel.

Step 7. Make sure the wings are inside and behind the wall material. The panel fastens directly to the wallboard using

the attached, captive hardware. Tighten the mounting screws until each wing firmly "grabs" the wall.

Step 8. Align the clips on the inside of the bezel with the mounting pins inside the frame and press firmly into place.

Upload Application - Software

Step 9. Connect the power adapter to AC power and wait for the panel to "boot" up; the panel boots automatically and launches

the AVSnap

initial setup application displaying system details. Follow the instructions to upload the application or quit the

setup application and use a USB drive to install the application.

Step 10. Once all software has been installed, close all open applications and put a shortcut to the application in the startup folder. Run the COMMIT

batch file located on the desktop and restart the computer from the "Start" menu.

Step 11. Verify the panel boots up and automatically launches the control software. The unit is now operational.

3. Limited Warranty/Return Policies

Please see the ALTINEX website at www.altinex.com for details on warranty and return policies.

Summary of content (8 pages)

PAGE 1
CP452CP452-009 MultiTouch™ MultiTouch™ InIn-Wall Widescreen Panel Welcome! We greatly appreciate your purchase of the CP452-009. We are sure you will find it reliable and simple to use. Superior performance for the right price, backed by solid technical and customer support is what ALTINEX has to offer. User’s Guide 1.3 Cleaning • Unplug the CP452-009 adapter before cleaning and clean only with a dry cloth. Never use strong detergents or solvents such as alcohol or thinner.
PAGE 2
CP452 CP452-009 User’s Guide 4. Technical Specifications Specifications are subject to change. See www.altinex.com for up-to-date information. Features/Description CP452-009 Details LCD Size LCD Resolution LCD Colors CPU RAM Solid State Drive 8.9 in 262k CF Type II USB 2.0 Type A F (4) RS-232 DB9 M (2) LAN RJ-45 F (2) 3.5 mm F (1) Mic In 3.5 mm F (1) USB Panel Mount Cable Body H x W x D ** 4.6 x 8.3 x 1.5 in (117 x 210 x 38 mm) Bezel H x W x D ** 6.5 x 11.2 x 0.
PAGE 3
CP452 CP452-009 User’s Guide 5. About Your CP452-009 MultiTouch Widescreen Panel The CP452 touch screen controller is specifically designed for in-wall installations. It is ideal for a wide variety of control applications.
PAGE 4
CP452 CP452-009 User’s Guide 6.
PAGE 5
CP452 CP452-009 User’s Guide Diagram 2: Dimensions 10.5" [267 mm] 6.2" [157 mm] 1.5" [38 mm] 8.3" [210 mm] 1.5" [38 mm] 4.6" [117 mm] 6.2" [157 mm] 2.
PAGE 6
CP452 CP452-009 User’s Guide Diagram 3: Bezel Dimensions 11.2" [284 mm] 6.5" [164 mm] 0.
PAGE 7
CP452 CP452-009 User’s Guide 7. Operation 7.3 Installing Files and Applications The CP452 is designed for use in a fixed application where the system boots up directly into the user application and does not allow access to the operating system. The application and GUI interface are normally created using a standard desktop computer and then installed onto the CP452 using a USB drive or network connection.
PAGE 8
CP452 CP452-009 User’s Guide 8. Troubleshooting Guide We have carefully tested and have found no problems in the supplied CP452. However, we would like to offer suggestions for the following: Symptom Resolution 1. Verify the adapter is plugged into a working AC outlet and that the outlet has power. Use only the AC adapter that was shipped with the unit. Power Is Not On 2. Verify the DC power plug coming from the AC adapter is plugged all the way into the CP452. 3.