User`s guide

ManualsBrandsAltinex ManualsComputer equipmentAC301-201

TP115

TP115TP115

TP115-

-201/202

201/202 201/202

201/202

Video+Audio

Video+AudioVideo+Audio

Video+Audio+IR+RS232

+IR+RS232+IR+RS232

+IR+RS232

to TP

o TPo TP

o TP

User’s Guide

400-0554-002

Control Wiring

Audio

Wiring

Welcome!

We greatly appreciate your purchase of the TP115-201/202 Video + Audio+

IR+ RS-232 to Twisted Pair Transmitter/Receiver. We are sure you will find it

reliable and simple to use. Superior performance for the right price, backed by

solid technical and customer support is what ALTINEX has to offer.

We are committed to providing our customers with Signal Management

Solutions

to the most demanding audiovisual installations at competitive

pricing and we welcome you to join the ranks of our many satisfied customers

throughout the world.

1. Precautions and Safety Warnings

Please read this manual carefully before using your TP115-201/202. Keep this

manual handy for future reference. These safety instructions are to ensure the

long life of your TP115-201/202 and to prevent fire and shock hazards. Please

read them carefully and heed all warnings.

1.1 General

• Qualified ALTINEX service personnel or their authorized representatives

must perform all service.

1.2 Installation Precaution

• To prevent fire or shock, do not expose units to water/moisture. Do not

place in direct sunlight, near heaters or heat-radiating appliances, or near

liquids. Exposure to sunlight, smoke, or steam can harm internal

components.

• Handle carefully; dropping or jarring can damage the unit.

Do not pull on any cables that are attached to the TP115-201/202.

1.3 Cleaning

• Clean only with a dry cloth. Never use strong detergents or solvents such as

alcohol or thinner. Do not use a wet cloth or water to clean the unit. Do

not open the unit to clean.

1.4 FCC Notice

• This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

• This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions found herein,

may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

• Any changes or modifications to the unit not expressly approved by

ALTINEX, Inc. could void the user’s authority to operate the equipment.

2. Installation Procedure

Note: Download and read the online manual to become familiar with this product and for additional details.

LEDs Power: ALTINEX logo is illuminated.

Signal: GREEN= VGA, RED=Component (YPbPr)

EDID: GREEN= Using local monitor EDID. RED= Using ALTINEX internal EDID.

Activity: Shows data traffic on the IR or RS-232 data lines.

Data Transmitting IR/RS-232 data requires the construction of a cable as shown. For best results use multi-conductor stranded wire, 24-28 AWG, and the

terminal block connector with captive screws (included). IR/RS-232 activity may cause momentary "glitches" or "muting" in the audio quality.

Audio Analog audio is available for VGA input; there is no digital audio with VGA input.

Component/YPbPr audio accepts digital (coax) or optical audio.

Local audio is the same format as the input audio.

Step 1. Place the TP115-201 Transmitter and TP115-202 Receiver at their destinations and

apply power; ALTINEX logos illuminate.

Step 2. Connect the video and audio output from the local device (PC, DVD, etc.) to the VGA/COMPONENT and

AUDIO inputs on the TP115-201. Cables are provided for a standard PC connection.

Step 3. Connect the local outputs (video and audio) on the TP115-201 to the local display and/or speakers if available.

The local outputs are identified by arrows pointing out of the TP115-201.

Step 4. Connect a CAT-5 cable between the TP connectors of the two units. For best results use ALTINEX low skew cable.

Step 5. Connect the TP115-202 Receiver to a display and speakers (or other audio receiving device).

Step 6. Verify the picture quality on the receiving display is equivalent to the quality as displayed on the local monitor. If the quality of the image is poor or

nonexistent, it may be necessary to adjust the video equalization on the TP receiver. Adjust the equalization incrementally and wait between

adjustments as some displays respond slowly to changes in the incoming video signal.

Step 7. For control wiring, if transmitting IR data from the receiver to the transmitter, install the optional IR Emitter to the 3.5 mm mono jack labeled IR OUT.

The emitter end of the cable should be place on or near the IR eye of the receiving device. See Section 7 for more details.

3. Limited Warranty/Return Policies

Please see the ALTINEX website at www.altinex.com for details on warranty and return policies.

Summary of content (13 pages)

PAGE 1
TP115TP115-201/202 Video+Audio+IR+RS232 Video+Audio+IR+RS232 to TP User’s Guide Welcome! We greatly appreciate your purchase of the TP115-201/202 Video + Audio+ IR+ RS-232 to Twisted Pair Transmitter/Receiver. We are sure you will find it reliable and simple to use. Superior performance for the right price, backed by solid technical and customer support is what ALTINEX has to offer. 1.
PAGE 2
TP115TP115-201/202 User’s Guide 4. Technical Specifications Specifications are subject to change. See www.altinex.com for up-to-date information. Features/Description Input Connectors RGBHV or YPbPr Stereo Audio Power IR IN, RS-232, +5V Out Output Connectors Local Monitor Local Audio Main Output IR Compatibility PC Signal Resolutions HDTV Resolutions Accessories Included Cable, VGA 6 ft 15-pin HD Cable, Audio 3.
PAGE 3
TP115TP115-201/202 User’s Guide 5.
PAGE 4
VGA / COMPONENT TWISTED PAIRS CONVERTOR RED YPbPr/ GREEN VGA GND Digital Audio In on Left or Right INFRARED AUDIO Steps Connect audio and video inputs according to top label. Connect local outputs to local display and/or speakers. Connect twisted pair (TP) out to TP input of TP receiver. Apply power to the TP115-201; verify picture quality at receiver. Digital audio input on left or right channel of 3.5 mm. Local audio is the same format as input audio. 1. 2. 3. 4.
PAGE 5
Audio Steps Digital audio input on left or right channel of 3.5 mm. Local audio is the same format as input audio. 1. Connect twisted pair (TP) in to TP output of TP transmitter. 2. Connect outputs to destination display and/or speakers. 3. Apply power to the TP115-202; verify picture quality at display. Adjust video equalization if necessary. on Left or Right IR Receiver: AC301-110 IR Emitter: AC301-111 (to IR OUT) +9 VDC IN 2.5 mm JACK IR OUTPUT 3.
PAGE 6
TP115TP115-201/202 User’s Guide 6.
PAGE 7
TP115TP115-201/202 User’s Guide Diagram 2: RJ-45 Pinout Pin Number RJRJ-45 Output Signals 1 Orange/White 2 Orange 3 Green/White 4 Blue 5 Blue/White 6 Green 7 Brown/White 8 Brown Table 1 Standard 568B Wiring Color Code 400-0554-002 7
PAGE 8
TP115TP115-201/202 User’s Guide Diagram 3: Internal View Transmitter Video + Stereo Audio + RS-232 + IR to CAT-5 Transmitter 400-0554-002 8
PAGE 9
TP115TP115-201/202 User’s Guide Diagram 4: Internal View Receiver CAT-5 to Video + Stereo Audio + RS-232 + IR Receiver 400-0554-002 9
PAGE 10
TP115TP115-201/202 User’s Guide Diagram 5: Optional Accessories 400-0554-002 10
PAGE 11
TP115TP115-201/202 User’s Guide 7. Operation 7.3 Audio Wiring (IR/RS-232) The TP115-201 and TP115-202 combination requires only one adjustment to be made for optimal performance; video equalization. Video equalization is typically needed for cable runs of 50 ft (15 m) or more. 7.3.1 Analog Audio (RGBHV video) Analog audio is available for RGBHV video only and uses a standard 3.5 mm stereo audio cable. 7.
PAGE 12
TP115TP115-201/202 User’s Guide 7.4 Control Wiring (IR/RS-232) 7.4.1 IR Wiring In order to send an IR signal from a remote control at the transmitter to the display or projector at the receiver, an IR receiver (AC301-110) is needed at the transmitter along with an IR emitter (AC301-111) at the receiver.
PAGE 13
TP115TP115-201/202 User’s Guide 8. Troubleshooting Guide We have carefully tested and have found no problems in the supplied TP115-201/202. However, we would like to offer suggestions for the following: Symptom ALTINEX Logo is NOT Illuminated Yellow Resolution 1. Make sure the unit is plugged into a working AC outlet and the DC plug is inserted all the way into the switcher. 2. Use only the power adapter provided. There is no EDID available on the local monitor or the local monitor is not connected.