SWITCHER MANUAL PART NUMBER: 400-0378-004 SW1956CT 2–IN, 1–OUT TWISTED PAIR AUTO-SWITCHER USER’S GUIDE
SWITCHER TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS................ 2 GENERAL..........................................................2 INSTALLATION..................................................2 CLEANING.........................................................2 FCC NOTICE .....................................................2 ABOUT YOUR SW1956CT ...................................... 3 TECHNICAL SPECIFICATIONS.............................. 3 PRODUCT DESCRIPTION ..............................
SWITCHER PRECAUTIONS / SAFETY WARNINGS 1.4 CLEANING 1 Please read this manual carefully before using your SW1956CT Switcher. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your SW1956CT and to prevent fire and shock hazards. Please read them carefully and heed all warnings. • 1.1 GENERAL • • 1.5 FCC NOTICE Qualified ALTINEX service personnel or their authorized representatives must perform all service. 1.
SWITCHER ABOUT YOUR SW1956CT 2 TECHNICAL SPECIFICATIONS Specifications are subject to change. See www.altinex.com for up-to-date information. SW1956CT 2-In, 1 Out Twisted Pair Auto-Switcher FEATURES/ DESCRIPTION The SW1956CT is a 2-In, 1-Out Twisted Pair Auto-Switcher. The SW1956CT switches automatically upon signal detection, but may also be controlled manually. The SW1956CT is designed to switch ALTINEX Twisted Pair transmitter and receiver signals.
SWITCHER MECHANICAL SW1956CT ELECTRICAL Material 0.100 in Al Input Signal Finish Gray Height 3.000 in ( 76 mm) Width 4.380 in (111 mm) Depth 1.000 in ( 25mm) Weight 0.40 lb (0.18 kg) Horizontal 15-200 kHz Ship Weight 2.00 lb (0.91 kg) Vertical 20-190 Hz T° Operating 10°C-35°C Cross-talk -40 dB @ 10 MHz T° Maximum 50°C Coupling DC Humidity Analog Signal SW1956CT Output Video Signals Analog Signal Power Consumption 40,000 hrs (min.) External Adapter: 9 VDC Table 2.
SWITCHER PRODUCT DESCRIPTION 400-0378-004 4 5
SWITCHER APPLICATION DIAGRAMS 5 DIAGRAM 1: TYPICAL SETUP ALTINEX includes a remote control switch with the SW1956CT. The remote switch has a 6 ft cable and may used to control the switcher manually. When the remote control switch is connected to the INPUT SELECT jack, INPUT 1 will be selected if the channel select contact is closed. INPUT 2 will be selected if the channel select contact is open. The switching will be identical whether there are one or two active signals.
SWITCHER DIAGRAM 2: INTERNAL VIEW CONTACT CLOUSURE SIGNAL DETECT INPUT1 TWISTED PAIR RJ-45 OUTPUT TWISTED PAIR RJ-45 INPUT1 INPUT2 INPUT2 2.
SWITCHER INSTALLING YOUR SW1956CT 6 OPERATION Step 1. Connect the ALTINEX power adapter that is supplied with the unit to the power port. There are no settings to adjust on the SW1956CT Auto-Switcher. The SW1956CT will operate successfully as long as cables are attached properly and other technical specifications are followed. CAUTION: The POWER port and the INPUT SELECT port use the same connector type. Make sure the power adapter is connected to the POWER port.
SWITCHER TROUBLESHOOTING GUIDE Cause 2: 8 We have carefully tested and have found no problems in the supplied SW1956CT unit. However, we would like to offer the following suggestions: Solution 1: Remove the input signals from the switcher. If the IN 2 LED is off, call ALTINEX at (714) 990-2300. If the IN 2 LED is on, see Solution 2. 8.1 POWER LED IS OFF Cause 1: Solution 2: Connect a properly formatted signal from an ALTINEX Twisted Pair transmitter to INPUT 1.
SWITCHER Solution 3: Bypass the switcher and connect the output of the transmitter directly to the input of the receiver. If the display is good, then call ALTINEX at (714) 990-2300. If there is still no display, see Cause 4. ALTINEX POLICIES Cause 4: Cable connections are incorrect. 9.2 CONTACT INFORMATION Solution: Make sure that cables are properly connected. Also, make sure that the continuity and wiring are good. If there is still no display present, see Cause 5.