MULTI-TASKER MANUAL PART NUMBER: 400-0096-004 MT106-100 SCAN REDUCER CARD FOR TM MULTI-TASKER USER’S GUIDE
MULTI-TASKER TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS .............. 2 1.1 GENERAL ................................ .................. 2 1.2 INSTALLATION ................................ .......... 2 1.3 CLEANING ................................ ................. 2 1.4 FCC / CE NOTICE................................ ...... 2 ABOUT YOUR MT106-100................................ .. 3 TECHNICAL SPECIFICATIONS ......................... 3 DESCRIPTION OF MT106-100 ...........................
MULTI-TASKER PRECAUTIONS / SAFETY WARNINGS interference operation. 1 Please read this manual carefully before using your MT106-100. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your MT106-100 and to prevent fire and shock hazard. Please read them carefully and heed all warnings. • Handle the MT106-100 carefully. Dropping or jarring can damage the card. • Do not pull the cables that are attached to the MT106-100.
MULTI-TASKER ABOUT YOUR MT106-100 2 TECHNICAL SPECIFICATIONS MT106-100 Scan Reducer Card 3 FEATURES/DESCRIPTION MT106-100 GENERAL Inputs Input Connector (1) 15-pin HD Female Outputs (3) BNC Female Composite Video Connectors (1) 4-pin Mini-DIN S-Video Connector Compatibility VGA, SVGA Input (to 100Hz) XGA (up to 75 Hz) Composite, S-Video Output (NTSC or PAL) Table 1. MT106-100 General The MT106-100 is a Scan Reducer Card designed for use in a Multi-Tasker enclosure.
MULTI-TASKER DESCRIPTION OF MT106-100 4 4 4
MULTI-TASKER APPLICATION DIAGRAM 5 Application 1 Application 2 5 5
MULTI-TASKER Application 3: Internal View of the MT106-100 6 6
MULTI-TASKER INSTALLING YOUR MT106-100 6 Step 1. Slide the MT106-100 into an available slot in the Multi-Tasker™ Basic Enclosure in order to connect to the bus. Make sure that the MT106-100 Scan Reducer card fits into place. Secure the card to the Multi-Tasker™ by tightening the retainer screws located on the top and bottom of the MT106-100 Scan Reducer card. Square brackets “[ command. ]” are part of the 2. Use uppercase letters for all commands.
MULTI-TASKER default values and place the card in NTSC format. Example: One MT106-100 card is in slot #2 of unit 3. Sending the command [VERC2U3] to the Multi-Tasker™ Basic Enclosure will yield the following feedback: 4. [ + ] or [ - ] These commands allow the user to increase or decrease the selected attribute value. They must be used immediately following one of the following STATUS commands.
MULTI-TASKER 5. [HPOSnCi] - Set Value Command Format: [VPOSnCiUy] This command sets the Horizontal Position to an absolute value. It also makes the Horizontal Position adjustment the active control. n Ci = card ID (i = slot number) Uy = unit id (i = 0 to 9) (refer to the MT100-100 user’s guide for explanation) Command Format: [HPOSnCiUy] n = a value from 0 to 20 = a value from 0 to 20 Example: Ci = card ID (i = slot number) There is an MT106-100 in slot 2 of unit ID 3.
MULTI-TASKER also returns the status of the current Vertical Size. As the active control, it may be adjusted using the [ + ] and [ - ] commands. Example: There is an MT106-100 in slot 2 of unit ID 3. Set the Horizontal Size to the value of 12 by sending the command [HSIZE12C2U3]. Command Format: [VSIZECiUy] Ci = card ID (i = slot number) 10.
MULTI-TASKER Zoom value. As the active control, it may be adjusted using the [ + ] and [ - ] commands. Command Format: [BRIGCiUy] Ci = card ID (i = slot number) Command Format: [QZOOMCiUy] Uy = unit id (i = 0 to 9) (refer to the MT100-100 user’s guide for explanation) Ci = card ID (i = slot number) Uy = unit id (i = 0 to 9) (refer to the MT100-100 user’s guide for explanation) Example: There is an MT106-100 in slot 2 of unit ID 3. View the current Brightness and make Brightness the active control.
MULTI-TASKER output. In order to view the actual video signal again, send the command [BAR0C4U0]. Example: There is an MT106-100 in slot 2 of unit ID 3. View the current Sharpness and make Sharpness the active control. 21. [HELP] In MTSetup.exe, this command displays a list of the commands available for the MT106-100 along with a brief description.
MULTI-TASKER 24. [G] This command is used to request group data. With the command, the user can identify which input or output of a particular group is on. 7) [VPOS] Set the Vertical Position 8) [VPOS] Adjust/Read Vert.
MULTI-TASKER Cause 3: Card cage slot has a problem. 8.3 NO DISPLAY Solution 1: Test the card in other slots of the card cage. If the slot was damaged, the card may work in other slots. If other slots work and the LED lights, the problem is the card cage slot. The card cage may require service. Call ALTINEX at (714) 990-2300. If the other slots do not work and the LED is still not lit, see Solution 2. Cause 1: The source has a problem.