SWITCHERS MANUAL PART NUMBER: 400-0030-003 MX2226AT 6-IN, 1-OUT RGBHV SWITCHER USER’S GUIDE
SWITCHERS TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS .............. 2 GENERAL ......................................................... 2 INSTALLATION................................................. 2 CLEANING ........................................................ 2 FCC / CE NOTICE............................................. 2 ABOUT YOUR MX2226AT SWITCHER ............... 3 TECHNICAL SPECIFICATION ............................. 3 MX2226AT DESCRIPTION ..................................
SWITCHERS PRECAUTIONS / SAFETY WARNINGS • 1 Please read this manual carefully before using your MX2226AT Switcher. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your MX2226AT and to prevent fire and shock hazard. Please read them carefully and heed all warnings. • 1.1 GENERAL • • Unauthorized personnel shall not open the unit since there are high-voltage components inside.
SWITCHERS • The MX2226AT may be rack-mounted using hardware supplied with the unit. Any changes or modifications to the unit not expressly approved by ALTINEX, Inc. could void the user’s authority to operate the equipment.
SWITCHERS (pass-through) Output Sync Signal Composite Sync Sync on Green Impedance Frequency Compatibility Typical Video Bandwidth Horizontal Vertical Horizontal Position Range Cross-talk Coupling Power Power Consumption Table 3. MX2226AT Electrical TTL(+/-), Analog 0.3-1.0V (unbuffered) -0.
SWITCHERS APPLICATION DIAGRAM 5 5 5
SWITCHERS INSTALLING YOUR SWITCHER SET DEFAULT POWER UP INPUT: 6 This function allows a user to define which input will be selected at power up. To define the default power on the input channel, while turning ON the unit, press the desired channel switch and hold it for approximately 2 seconds until you hear a short beep. Turn the unit OFF and then turn it back on again. The LED of the selected input should be ON. For factory default the input is set to INPUT1. Step 1.
SWITCHERS button should light up. To enable the video portion, press the button again and the LED will be in an OFF position. This feature is designed to work only with RGBHV, RGBS and RGsB format signals. It is similar to the ALL OFF mode except that there is only sync signal sent to the output for display. STEP: This feature allows cycling through the inputs one at a time. It is used to select the next input from an ALL OFF condition.
SWITCHERS After processing a valid command, an [OK] string will be returned, followed by a command echo. For instance, if a command, [INP1] is sent to the MX2226AT Switcher, it would return the feedback as [OK] [INP1]. The only exception is that with the [VERN] command, which is the corresponding firmware version of the switcher, [1.0] is returned as feedback. 5 GND RS-232 connection of PC with DB-9 port MX2226AT Terminal Block PC DB-25 port pin no. MX2226AT Terminal IBM PIN No.
SWITCHERS 11-IN 1-OUT SWITCHER 7.5 MASTER/SLAVE CONTROL (RS-232): The feedback codes allow multiple MX2226AT Switchers to be connected in a Master-Slave configuration, if desired. When the control port of two units are connected as shown below, the slave unit duplicates the actions of the master unit.
SWITCHERS 3 4 5 6 7 switchers independently with one RS232 card in a control system? Why? Can the MX2226AT be used to pass Composite Video, S-Video, and Component Video? OFF mode. Yes, simply use the corresponding channels to pass the signals (e.g. For composite video, you may use the red channel or you may use the blue channel). Since the MX2226AT is a relay switcher, it can be used as a contact closure control or to switch virtually to any type of video, sync, audio, or even RS-232 signals.
SWITCHERS 6 feet, 5-BNC M to 5-BNC M CB4206MR 12 feet, 5-BNC M to 5-BNC M CB4212MR 25 feet, 5-BNC M to 5-BNC M CB4225MR 50 feet, 5-BNC M to 5-BNC M CB4250MR 75 feet, 5-BNC M to 5-BNC M CB4275MR CB42100MR 100 feet, 5-BNC M to 5-BNC M CB42150MR 150 feet, 5-BNC M to 5-BNC M SUPER HIGH RESOLUTION 5 BNC TO 5 BNC COAXIAL CABLE Bulk cable (500 feet minimum) CB4400MR 6 feet, 5-BNC M to 5-BNC M CB4406MR 12 feet, 5-BNC M to 5-BNC M CB4412MR 25 feet, 5-BNC M to 5-BNC M CB4425MR 50 feet, 5-BNC M to 5-BNC M CB4450MR 75
SWITCHERS www.altinex.com. When using RS-232 commands to the switcher where the RX pin of the MX2226AT is connected to the TX pin of the computer, make sure that the cable is made according to the manual. ALTINEX POLICY If your product is in warranty and needs service, contact the ALTINEX Sales Department for an RMA (Return Material Authorization). Products returned without an RMA number may experience a delay in service.
