User`s guide

SPECIAL APPLICATION
400-0384-002
25
REMEMBER: A command sent without the unit
ID will be executed by all the
PE1005’s connected to the
RS-232 port.
65. [SIDn]
This command sets the ID number of all cards
connected to the RS-232 bus to the same value.
The default unit ID is zero.
Command Format: [SIDn]
n = New ID (n = # from 1 to 99)
Example:
Send the command [SID1] to the system. The
card ID is now one, and “C1” must be included
at the end of each command line, as in
“[VERC1]”, for only the unit with ID1 to respond.
REMEMBER: A command sent without the unit
ID will be executed by all the
PE1005’s connected to the
RS-232 port.
66. [SIDnCi]
This command sets the ID number of a single
card to a new ID number. Only the cards that
have the matching ID will be changed.
Command Format: [SIDnCi]
n = New ID (i = # from 1 to 99)
Ci = Card ID (n = # from 1 to 99)
Example:
Send the command [SID10C1] to the bus. The
card with the ID of “C1” will now become “C10”.
Now, “C10” must be included at the end of the
command string for only that card to respond.
67. [RSN]
This command reads and then displays the ID
number of the unit.
Command Format: [RSN]
Example:
The PE1005 was set to an ID value of 3. Send
the command [RSN] and the system will return
the following feedback:
PE1005 ID#3
7.3 SUMMARY OF COMMANDS
1) [STATUS] Display status of the card.
2) [FRESET] Perform factory reset.
3) [VER] Display card information.
4) [TEST] Test memory IC's.
5) [WAIT] Suspend operation.
6) [RDI] Read input status.
7) [RDRL] Read relay status.
8) [WRRLx
1
x
2
x
3
x
4
] Set relays individually.
9) [WRRLk=x] Set one or all relays.
10) [WRIN] Assign sub to input port.
11) [RDIN] Read sub to be executed.
12) [WRS] Write a subroutine.
13) [WRLS] Write a subroutine label.
14) [RDS] Display subroutine data.
15) [RDLS] Display a subroutine label.
16) [CLRS] Clears subroutine content.
17) [CLRLS] Clears subroutine's label.
18) [SUB] Execute a subroutine.
19) [HELP] Show RS-232 commands.
20) [SETTIME] Set the time of day.
21) [SETDAY] Set the day of the week.
22) [SETDATE] Set the day/month/year.
23) [RDTIME] Read internal time clock.
24) [RDDAY] Read day of the week.
25) [RDDATE] Read date from clock.
26) [SET1ALRM1] Set Alarm 1 Mode 1.
27) [SET1ALRM2] Set Alarm 1 Mode 2.
28) [SET1ALRM3] Set Alarm 1 Mode 3.
29) [SET1ALRM4] Set Alarm 1 Mode 4.
30) [SET1ALRM5] Set Alarm 1 Mode 5.
31) [SET2ALRM1] Set Alarm 2 Mode 1.
32) [SET2ALRM2] Set Alarm 2 Mode 2.
33) [SET2ALRM3] Set Alarm 2 Mode 3.
34) [SET2ALRM4] Set Alarm 2 Mode 4.
35) [SET2ALRM5] Set Alarm 2 Mode 5.