SWITCHER MANUAL PART NUMBER: 400-0426-006 SW104-130 2-IN VIDEO+ AUDIO TO TWISTED PAIR (TP) OUTPUT, AUTO-SWITCHER/TRANSMITTER USER’S GUIDE
SWITCHER TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS................ 2 GENERAL..........................................................2 INSTALLATION..................................................2 CLEANING.........................................................2 FCC NOTICE .....................................................2 ABOUT YOUR SW104-130 ...................................... 3 TECHNICAL SPECIFICATIONS.............................. 3 PRODUCT DESCRIPTION .............................
SWITCHER PRECAUTIONS / SAFETY WARNINGS 1.4 CLEANING 1 Please read this manual carefully before using your SW104-130 Switcher. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your SW104-130 and to prevent fire and shock hazards. Please read them carefully and heed all warnings. • 1.1 GENERAL • 1.5 FCC NOTICE • Unauthorized personnel shall not open the unit since there are high-voltage components inside.
SWITCHER ABOUT YOUR SW104-130 2 TECHNICAL SPECIFICATIONS Specifications are subject to change. See www.altinex.com for up-to-date information. SW104-130 2-In Video+ Audio to TP Output, Auto-Switcher/Transmitter with Local Output FEATURES/ DESCRIPTION SW104-130 Inputs The SW104-130 Auto-Switcher is designed to switch between two video+ audio sources. The selected source is converted and transmitted using ALTINEX’s Twisted Pair standard as well as buffered and output locally.
SWITCHER MECHANICAL SW104-130 ELECTRICAL Material 0.091 in Al Video Input Signal SW104-130 Finish Black Height 0.960 in (24 mm) Video Impedance 75 ohms Width 4.300 in (109 mm) SYNC Signal TTL (+/-) Depth 5.200 in (132 mm) SYNC Impedance 10 kohms Weight 1.00 lb (0.45 kg) Audio Input Signal T° Operating 10°C-35°C T° Maximum 50°C Humidity Video Signal Impedance 10 kohms Level 0.9 Vp-p max Twisted Pair Output 90% non-condensing MTBF (calculations) 1.
SWITCHER PRODUCT DESCRIPTION 4 LOCAL MONITOR COMPUTER/ COMPONENT VIDEO INPUT1 AUDIO LOCAL OUTPUT AUDIO INPUT1 4TP MAIN OUTPUT VIDEO EQUALIZATION COMPUTER/ COMPONENT VIDEO INPUT2 CONTACT CLOSURE AUDIO INPUT2 CONTROL SWITCH POWER APPLICATION DIAGRAMS 5 DIAGRAM 1: TYPICAL SETUP TP115-111 SW104-130 400-0426-006 5
SWITCHER DIAGRAM 2: INTERNAL VIEW SW 104-130 CONTROL LEFT AUDIO STEREO 3.5 mm (VIDEO 1) AUDIO STEREO 3.5 mm (VIDEO 2) RIGHT LOCAL 3.5 mm AUDIO MONO LEFT RIGHT CH1 CONTACT CLOSURE CONTROL SWITCH CH2 RED VIDEO INPUT1 COMPUTER/ COMPONENT 15-PIN HD BLUE GREEN HOR PLUG AND PLAY VER CONTROL HOR VER SYNC PROCESSING H/W PAIR 4 EQ VIDEO INPUT2 COMPUTER/ COMPONENT 15-PIN HD PAIR 1 RED OUTPUT TWISTED PAIR RJ-45 PAIR 3 BLUE PAIR 2 GREEN PLUG AND PLAY CONTROL GREEN BLUE RED HOR VER POWER 2.
SWITCHER INSTALLING YOUR SW104-130 6 OPERATION Step 1. Make sure to use the ALTINEX power adapter supplied with the unit. Connect the power adapter to the power port. The Power and Input 2 LEDs should turn on. The SW104-130 requires only one adjustment to be made for optimal performance. The adjustment is video equalization for long cable lengths. The remaining controls are for input selection only. 7.
SWITCHER TROUBLESHOOTING GUIDE Cause 3: 8 We have carefully tested and found no problems in the supplied SW104-130 unit. However, we would like to offer the following suggestions: Solution 1: Remove the input signals from the switcher. If the Input 2 LED is off, call ALTINEX at (714) 990-2300. If the Input 2 LED is on, see Solution 2. 8.1 LEDs ARE OFF Cause 1: The power adapter is installed wrong. Solution 2: Connect a properly formatted video type signal to Input 1.
SWITCHER Cause 3: Signal is bad or missing. ALTINEX POLICIES Solution 1: Make sure the switcher output is connected to the monitor. If there is still no display, see Solution 2. 9.1 LIMITED WARRANTY/RETURN POLICIES Please see the ALTINEX website at www.altinex.com for details on warranty and return policies. Solution 2: Remove both inputs to the switcher and connect the active signal from the source to Input 2. If there is still no display, see Solution 3. 9.2 CONTACT INFORMATION ALTINEX, Inc.
