Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Chalice Installation & Operation Manual Lighting BRINGING IMAGINATION TO LIGHT 57 Alexander St., Yonkers, NY 10701 © 2012 Altman Stage Lighting, Inc. Tel: 914-476-7987 1 Visit our website at www.altmanlighting.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Table of Contents Safety Instructions Page 3 Description and Packing List Page 4 Setup and Installation Page 5 Features Page 6 Operation Page 7 DMX Mode Page 8 ∙ Personalities Page 9 ∙ Resolution Page 10 ∙ Stand Alone Mode Page 11 ∙ Fixed Color Mode Page 12 ∙ Master Mode Page 13 Wiring Details Page 14 J-Box and Ball Mount Details Page 15 Cable Mount Details Page 16 Pendant Chalice, 100W Page 17 Pendant Chalic
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS FOR SPECTRA SERIES LED LIGHTING FIXTURES. LES INSTRUCTIONS AU SUJET D’UN RISQUE D’INCENDIE LE CHOC ÉLECTRIQUE, OU LA BLESSURE AUX PERSONNES POUR SS-CYC-100.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l CDR50 & CDR100 Recessed Chalice™ LED Series Solid State Lighting Fixture DESCRIPTION The CDR50 & CDR100 Recessed Chalice LED lighting fixture is a recessed unit provided with knock-outs and terminal blocks to provide power and/or data to the fixture in recessed ceiling mount applications only.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l SETUP AND INSTALLATION Unpacking Remove the CDR50 & CDR100 Recessed Chalice lighting fixture from its shipping box. Set the unit down on a flat surface before proceeding. Remove the trim ring and lens from the fixture by squeezing the two tension springs on the trim ring and set aside. Lamping and Re-lamping The CDR50 & CDR100 Recessed Chalice lighting fixture is provided with an integral 50W and 100W LED light engine respectively.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Features The Chalice SERIES LED lighting fixtures are the first of its kind in the Theatrical and Architectural Lighting Industry offered by Altman Lighting. • Available in 3,000K White, 3,000K-6,000K tunable white, RGBA, RGBW or custom color combinations. • Compatible with DMX512 and RDM protocols. • 8/16 bit DMX512 control for smoother dimming.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l ( Firmware Version: V2.3.6) OPERATION There are 3 buttons below the 3 digit LED display on the side of the unit. The buttons are : (From left to right) [ HUNDREDS ] , [ TENS ] , [ ONES ]. All settings for Modes, DMX address, Personalities, etc., can be made by using the three buttons on the back of the unit while power is on. (Note: Display goes out after no activity for approx 4 sec. Touch any button once to bring it back on.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l DMX Mode: DMX Mode is used for Setting DMX address, Personalities, and Stand-alone Effects. This is the default mode for a new unit. (Also see Fixed Color Mode section on page 9.) To Switch to DMX Mode from Fixed Color Mode (or vice versa ) : Wait a few seconds until the display goes blank, • press and hold the [ ONES ] button • press and hold the [ TENS ] button • release the [ ONES ] button • release the [ TENS ] button.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l PERSONALITY ADDRESS SETTINGS LIST 601-608: 4-COLOR CHANNELS: 601 602 603 604 605 606 607 608 Personality #01 8 bit Uses 4 DMX Channels Channel order is RGBA Personality #02 8 bit Uses 4 DMX Channels Channel order is RGBA Personality #03 8 bit Uses 5 DMX Channels Channel order is RGBAM Personality #04 8 bit Uses 5 DMX Channels Channels order is RGBAM Personality #05 16 bit Uses 8 DMX Channels Channel order is RrG
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l RESOLUTION is selectable as either: 8 Bit (one DMX channel per color) this is normal resolution, or 16 Bit (two DMX channels per color) Coarse+Fine high resolution similar to moving lights.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l STAND-ALONE MODE (does not require a control console): Note: Must be in DMX Mode (see page 6). If Master Mode (see page 10) is on, stand-alone effects from a single unit will control other units connected via DMX cable to all synchronize. Set other units to DMX channel 001. (Do not use the Stand-Alone Effects while connected to a control console or a conflict may result.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l FIXED COLOR MODE: This is a special mode that allows you to manually select colors for a single unit using the 3 keys. (Also see DMX Mode on page 6.) To enter Fixed Color Mode (or exit to DMX Mode) : Wait a few seconds until the display goes blank, 1. press and hold the [ ONES ] button 2. press and hold the [ TENS ] button 3. release the [ ONES ] button 4.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l MASTER MODE ( Different than the Master Channel described on page 7.) Master Mode only works while in STAND-ALONE EFFECTS MODE (see page 8). It causes the unit that is set to Master Mode to behave like a console and Transmit 4-channel (RGBA) 8-bit DMX set on address 001, reflecting its present light output. Note: Only the first unit that is going to serve as the MASTER fixture should be set to Stand-alone Effects mode with Master Mode on.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Single DMX Cable: Cat-5 Cable pinout for RJ45 connector: DATA 1 is used for DMX IN (+,-,Common) DATA 2 IS USED FOR DMX OUT (+,-,Common) White/Orange Orange > DATA 1+ > DATA 1- >RJ45 Pin 1 (part of DMX IN) >RJ45 Pin 2 (part of DMX IN) White/Green Green > DATA 2+ > DATA 2- >RJ45 Pin 3 (part of DMX OUT) >RJ45 Pin 6 (part of DMX OUT) Blue White/Blue > N/C > N/C >RJ45 Pin 4 >RJ45 Pin 5 White/Brown Brown > DATA 1 COMMON > DATA 2 COMMO
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l WIRING DETAILS: Pendant: Data Connection Voltage Barrier Cat 5 DMX Data Connection White/Orange: Data 1+, XLR Pin 3 Orange: Data 1-, XLR Pin 2 White/Green: Data 2+, XLR Pin 5(OPTIONAL) Green: Data 2-, XLR Pin 4(OPTIONAL) White/Blue: Not Used Blue: Not Used White/Brown: Common, XLR Pin 1 Brown: Common, XLR Pin 1 Power Connection Cat 5 DMX Data Connection White/Orange: Data 1+, XLR Pin 3 Orange: Data 1-, XLR Pin 2 White/Green: Data 2+,
CHALICE DOWN LIGHT WASH LIGHTING Chalice DMX Terminator Wiring Chalice DMX Terminator TOP FRONT 120 Ohm Resistor White/ Brown White/ Orange Brown Orange White/ Brown Orange White/ Orange Brown Cat5 Cable from last Chalice in the line. DMX termination for Chalice should be installed on the DMX Cat5 cable bare end on the last fixture in the communication line. Lighting BRINGING IMAGINATION TO LIGHT 57 Alexander St., Yonkers, NY 10701 © 2012 Altman Stage Lighting, Inc.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l J-Box Connection Details: Ball Mount Details: Set Screw Threaded Ball Ground Screw Mounting Screws 2 x 8--32x1.5” Canopy Install the 1/4-20 flat head screw into the center threaded hole of the cross bar as shown. The Ground (green) screw is used by the Electrician to attach a wire to properly ground the Chalice LED fixture. Stem Chalice Fixture Use two (2) 8-32 screws to attach the crossbar to the junction box.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Cable Mount Details: 99-158 crossbar. Attaches to standard 3.5” octagonal J-box using (2) 8-32 screws (J-box not supplied) Grounding Screw 8-32 screws (not supplied) 99-94B-10 canopy. Manufactured for the weight of the fixture. 99-CC1/4-202P 2 piece coupler 3 x 99-102 Strain relief 99-AC3/32-240G 2.5mm flexible aircraft suspension cable provided, length to be specified at time of order.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Lighting BRINGING IMAGINATION TO LIGHT 57 Alexander St., Yonkers, NY 10701 © 2012 Altman Stage Lighting, Inc. Tel: 914-476-7987 17 Visit our website at www.altmanlighting.
Installation Manual WALL MOUNT CHALICE
STEP 1: FIX THE YOKE TO THE WALL WITH APPROPRIATE FASTENERS STEP 2 : REMOVE THE SHOULDER BOLTS FROM THE FIXTURE
STEP 3: INSERT THE FIXTURE BETWEEN THE YOKE AND FASTEN IT WITH REMOVED FASTENERS (STEP 2). MAKE SURE RUBBER WASHERS ARE IN BETWEEN YOKE AND FIXTURE. STEP 4: PERFORM THE REQUIRED WIRING TO LIGHTUP THE UNIT.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Lighting BRINGING IMAGINATION TO LIGHT 57 Alexander St., Yonkers, NY 10701 © 2012 Altman Stage Lighting, Inc. Tel: 914-476-7987 Recessed Chalice, 100W CDR100 18 Visit our website at www.altmanlighting.
Chalice Series I N S TA L L AT I O N & O P E R AT I O N M a n u a l Lighting BRINGING IMAGINATION TO LIGHT 57 Alexander St., Yonkers, NY 10701 © 2012 Altman Stage Lighting, Inc. Tel: 914-476-7987 Recessed Chalice, 50W CDR50 19 Visit our website at www.altmanlighting.