Phoenix LED Profile Spot Operation, Programming and Safety Manual Altman Lighting, Inc. 57 Alexander Street., Yonkers, NY 10701 1-800-4-ALTMAN SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
Table of Contents Introduction & Safety Instructions & Information Page 3 Yoke & Shutter Assembly Page 4 Accessory Instructions: Page 5 Retaining Latch, Iris Slot, Pattern Projections & Shutters Cleaning & Replacing Lenses Page 6 DMX Controls– Operation Menu & Controls Page 7 Player—Operation Menu & Control Page 8 Settings & Info— Operation Menu & Controls Page 9 Fixture Resolution 3000K, 5600K, RGBW Page 10 Fixture Resolution RGBA Page 11 General Maintenance & Troubleshooting Page 12 Alt
SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS FOR SPECTRA SERIES LED LIGHTING FIXTURES. Phoenix Series LED Profile Spot INTRODUCTION Congratulations on purchasing one of the finest lighting instruments available today! Before using your Phoenix LED Profile Spot, be sure to read all of the instructions in this manual.
YOKE & SHUTTER ASSEMBLY Shutter Rotation Lock Knob ***Shutter Assembly Screw Guides Shutter Handle Short Yoke Position T-Handles Lens Tube Yoke Bolts Cup Washers Pivot Covers Shutter Assembly ROTATING SHUTTER ASSEMBLY 1. Loosen shutter rotation lock knob on either side of the fixture. 2. Rotate shutter assembly 360° in either direction. 3. Tighten shutter rotation lock knobs to secure shutter assembly. 4.
ACCESSORY INSTRUCTIONS ACCESSORY RETAINING LATCH This unique retaining hatch is designed for positive locking and manual return. 1. Slide cover to right side. 2. Swing cover back. 3. Insert accessory. 4. Close cover. Make sure latch locks in place. DROP IN IRIS SLOT This larger slot can accept either a drop-in iris or a motorized pattern device (gobo rotator, yo-yo etc). The slot has a retractable cover to prevent light leak when not in use.
CLEANING / REPLACING LENSES WARNING: Never use glass or window cleaner or any abrasive material to clean a lens. These types of cleaners will stain the lens surface. Abrasive materials will damage the surface of the lens. 1. Remove focus lock knob, push in safety pin and slide lens barrel out. 2. Place barrel on a surface so that the two halves are oriented as the top and bottom. 3. Remove lower accessory cover with (2) screws. 4. Remove latch cover with (2) screws. 5.
Operation Menu and Options DMX Control -DMX Address (1-512) -DMX Resolution (8 Bit or 16 Bit) -Master Channel (Off or On) -Smoothing (Off or On) -DMX Loss (Off, Hold Last Command, Preset) To address your fixture follow these steps: 1-Power the fixture and wait for the startup to complete. The screen will turn off. 2-Press ENTER and you will see “DMX Control” press ENTER again. 3-When the screen shows “DMXAdr 1” press ENTER again.
Operation Menu and Options There is a player option in the menu where you can pre-program your fixture to play back up to 5 cues. The cues can run as short as 1 second or as long as 99 minutes. You can choose any of the colors you desire within your cues to create any look you want. You also have the option of putting a delay in between your cues. To program your cues follow the steps below. Press ENTER to turn the screen on. Press DOWN to get to the “player” option.
Operation Menu and Options Menu Category Control Type Option 1 Option 2 Settings Factory Default Yes Sure? Y No Sure? N Fan Speed Option 3 Fan Auto Factory Default No AUTO Fan On Display Backlight On On 5 seconds 10 seconds 30 seconds 60 seconds Screen Correction Normal/Upright Normal/Upright Flipped Auto Dimming Curve Linear Square Log Square Info LED Temperature Run Time/Hours Fixture Serial # LED Serial # Software Version Altman Lighting, Inc. 57 Alexander Street.
Fixture Resolution & Configuration Fixture Type: 250W 3000K & 5600K White 8 Bit (one DMX channel per color) this is normal resolution Channel 1 White 16 Bit (two DMX channels per color) Coarse & Fine high resolution. Channel 1 White Coarse Channel 2 White Fine Master Channel is selectable as ON or OFF and provides a Master Fade channel that dims all 4 colors proportionally at the same time in order to maintain the color.
Fixture Resolution & Configuration Fixture Type: 250W RGBA 8 Bit (one DMX channel per color) this is normal resolution Channel 1 Red Channel 2 Green Channel 3 Blue Channel 4 Amber 16 Bit (two DMX channels per color) Coarse & Fine high resolution.
General Maintenance In order to insure longevity of your fixture, regular cleaning is necessary. The lens and fan must be cleaned periodically to allow proper function of the fixture. Do not use alcohol or any other solvent with chemicals to clean the lens. When cleaning your lens, use a clean soft lint free cloth with damp with water. Do not use any hard materials to wipe the lens.