Instruction manual

ManualsBrandsAltman ManualsConsumer electronicsSSW-SP*-100

ALTMAN LIGHTING, INC.

SS-SP*-100 and SSW-SP*-100

Spectra-STAR PAR™ Series

Installation and Instruction Manual

¤!"#$#!%&'()*!+,-.',*-/!0*12!

34!%&56)*758!9'855'/!:;*<58=!

>5?!:;8<!$#4#$!@292%2!

A.;*5!B$C2C4D24BE4!F!G)6!B$C2BDD2$BE#!

%&'()*!+,-.',*-/!0*12!,=!)!=HI=,7,)8J!;K!%&'()*!9')-5!+,-.',*-!L;2/!0*12!

M9N51,K,1)',;*=!)85!=HIO51'!';!1.)*-5!?,'.;H'!*;',15P!!

L;NJ8,-.'Q!"#$#!R5S!"#$#T#ETU#!

???2)&'()*&'-21;(!

Summary of content (10 pages)

PAGE 1
ALTMAN LIGHTING, INC. SS-SP*-100 and SSW-SP*-100 Spectra-STAR PAR™ Series Installation and Instruction Manual ¤ 2010 Altman Lighting, Inc. 57 Alexander Street, Yonkers New York 10701 U.S.A. Phone 914.476.7987 • Fax 914.966.1980 Altman Lighting, Inc. is a subsidiary of Altman Stage Lighting Co., Inc. (Specifications are subject to change without notice) Copyright© 2010 Rev 2010-08-30 www.altmanltg.
PAGE 2
SAFETY INSTRUCTIONS INSTRUCTIONS DE SÛRETÉ INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS FOR SS-PAR-100 SERIES LED LIGHTING FIXTURES. LES INSTRUCTIONS AU SUJET D' UN RISQUE D'INCENDIE LE CHOC ÉLECTRIQUE, OU LA BLESSURE AUX PERSONNES POUR SS-P AR-100 AP P AREILS D'É CL AIR AG E DE LED.
PAGE 3
I N S T A L L A T I O N A N D I N S T R U C T I O N M A N U A L SS-SP*-100 and SSW-SP*-100 Spectra-STAR PAR™ LED Series Solid State Lighting Fixture DESCRIPTION The SS-SPP-100 and SS-SPY-100 LED lighting fixture is a portable outdoor weather rated unit with a flexible power supply cord and male and female DMX-512 data supply cords. The overall construction of the fixture includes corrosion protected aluminum die-cast housing and allows for a yoke or mounting brackets.
PAGE 4
I N S T A L L A T I O N A N D I N S T R U C T I O N M A N U A L SETUP AND INSTALLATION Unpacking Remove the LED lighting fixture from its shipping box. Set the unit down on a flat surface before proceeding. Lamping and Re-lamping The LED lighting fixture is provided with an integral LED light engine. Under normal operating conditions, the LED light engine should have a rated life expectancy of over 50,000 hours. There are no user serviceable parts inside. The entire LED assembly will need to be changed.
PAGE 5
I N S T A L L A T I O N A N D I N S T R U C T I O N M A N U A L FEATURES The LED lighting fixture complements the Theatrical and Architectural Lighting Industry and adds to the expanding Spectra-LED™ family of solid state LED luminaires offered by Altman Lighting, Inc. i Four-Colors: Red, Green, Blue, and Amber for more color combinations and better CRI. i Compatible with DMX-512 and RDM protocols including Wybron Responder System.
PAGE 6
I N S T A L L A T I O N A N D OPERATION I N S T R U C T I O N M A N U A L ( Firmware Version: V2.2.1 Date: 2010-08-23) SETTINGS There are 3 buttons below the 3 digit LED display on the side of the unit. The buttons are : (From left to right) [ HUNDREDS ] , [ TENS ] , [ ONES ]. All settings for Modes, DMX address, Personalities, etc., can be made by using the three buttons on the back of the unit while power is on. . (Note: Display goes out after no activity for approx 4 sec.
PAGE 7
I N S T A L L A T I O N A N D I N S T R U C T I O N M A N U A L EXAMPLE: Let's say that we want to select personality #05. We enter 605 on the display. After a few seconds the display will show ?05 . Since we want this, we press the [ONES] button (below the 5 ), and that enters personality #05 into memory.
PAGE 8
I N S T A L L A T I O N A N D I N S T R U C T I O N M A N U A L RESOLUTION is selectable as either: 8 Bit (one DMX channel per color) this is normal resolution, or 16 Bit (two DMX channels per color Coarse+Fine high resolution similar to moving lights). If unit is in 8 Bit mode, and the unit is set to DMX Channel 001, then the DMX channels would be: CH1 = Red, CH2 = Green, CH3 = Blue, CH4 = Amber.
PAGE 9
I N S T A L L A T I O N A N D I N S T R U C T I O N M A N U A L STAND-ALONE EFFECTS (does not require a control console): Note: stand-alone effects from a single unit will control other units connected via DMX cable to all synchronize. Set other units to DMX Channel 001. (Do not use the Stand-Alone Effects while connected to a control console or a conflict will result.
PAGE 10
I N S T A L L A T I O N A N D I N S T R U C T I O N M A N U A L Locked Mode To Lock (or unlock) the buttons: >Wait a few seconds until the display goes blank, > press and hold the [ ONES ] button > press and hold the [ HUNDREDS ] button > release the [ ONES ] button > release the [ HUNDREDS ] button. Display will show Loc for a moment and then blink. Buttons will have no effect until they are unlocked.