SXA18P QUICKSTART GUIDE ENGLISH ( 3 – 6 ) GUÍA DE INICIO RÁPIDO ESPAÑOL ( 7 – 10 )
QUICKSTART GUIDE (ENGLISH) BOX CONTENTS SXA18P Quickstart Guide Safety & Warranty Information Booklet QUICK SETUP 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Make sure all items listed in the BOX CONTENTS section are included in the box. READ SAFETY & WARRANTY INFORMATION BOOKLET BEFORE USING THE PRODUCT. Study the connection diagram in this guide. Place all devices in an appropriate position for operation. Make sure all devices are turned off and all faders and gain knobs are set to "zero.
Medium Array Configuration Below is an example of applying the HFC to four SXA18P’s in an array. In this particular configuration, the HFC on the top speaker is set at +3 dB, and the bottom speaker 0 dB. Small Array Configuration This is an example of the HFC application with two SXA18P’s in a small array, with the top speaker set at +3 dB and the bottom speaker at 0 dB. Do not stack more than two SXA18P speakers on the pole. Be sure to lock the two speaker cabinets with the original hardware.
Array Frame Connection The FB-1 frame is connected to SXA-HD-L and SXA-HD-R with ALTO quick release pins. LOCKING THE LOUDSPEAKERS TOGETHER Any time two or more SXA18P and SXA28P’s are arrayed together, they must be mechanically secured to each other. See the diagram below for details.
SXA-L3 L12 L11 CH3 CH1 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 L4 L4 R3 Powered Amplifiers CH4 CH2 CH4 CH2 CH1 CH3 CH4 CH3 CH1 CH2 CH3 CH4 CH1 CH2 L3 L3 R2 L3 L3 L8 R1 L2 L2 L5 BREAKER BREAKER BREAKER L1 AC INPUT AC INPUT AC INPUT L1 L5 L10 L11 L7 L6 L9 L4 L4 L3 L2 L1 L1 L2 L3 L4 L5 L6 L4 L12 R12 R11 R10 R9 L8 L7 L6 R1 R2 R2 CH4 CH2 CH4 CH2 CH4 CH2 CH4 CH2 R3 R4 CH1 CH2 R4 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 C
GUÍA DE INICIO RÁPIDO (ESPAÑOL) CONTENIDO DE LA CAJA SXA18P Guía de inicio rápido Folleto de información sobre la seguridad y la garantía INSTALACIÓN RÁPIDA Asegúrese de que todos los artículos indicados en CONTENIDO DE LA CAJA estén incluidos en la misma. LEA EL FOLLETO DE INFORMACIÓN SOBRE LA SEGURIDAD Y LA GARANTÍA ANTES DE UTILIZAR EL PRODUCTO. Estudie el diagrama de conexión incluido en esta guía. Coloque todos los dispositivos en una posición adecuada para su funcionamiento.
Configuración de arreglo mediano Se presenta a continuación un ejemplo de aplicación del HFC a un arreglo de cuatro SXA18. En esta configuración particular, el HFC que está sobre el altavoz de arriba se ajusta a +3 dB y el del altavoz de abajo a 0 dB. Configuración de arreglo pequeño Éste es un ejemplo de la aplicación del HFC con dos SXA18 en un arreglo pequeño, con el altavoz de arriba ajustado a +3 dB y el de abajo a 0 dB. No apile más de dos altavoces SXA18P/ 28P en la columna.
Conexión del bastidor para arreglos El bastidor FB-1 se conecta al SXA-HD-L y el SXA-HD-R con pasadores de liberación rápida ALTO. FIJACIÓN DE LOS ALTAVOCES Toda vez que dos o más SXA18P y SXA28P se colocan juntos en un arreglo, se deben sujetar mecánicamente entre sí. Consulte los detalles en el diagrama de abajo.
SXA-L3 L12 CH2 CH3 CH1 CH3 CH1 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 L4 L4 R3 R2 L3 L3 L8 L9 L4 L2 L5 BREAKER BREAKER BREAKER L1 AC INPUT AC INPUT AC INPUT L1 L5 L4 L3 L2 L1 L1 L2 L3 L4 L5 L6 L4 L10 L11 L12 L7 L6 R1 L2 Amplificadores alimentados CH4 CH2 CH4 CH4 CH1 CH3 CH4 CH2 CH3 CH1 CH2 L3 L3 R12 R11 R10 R9 L8 L7 L6 R1 CH3 CH1 CH3 CH1 CH3 CH1 CH3 CH1 R1 R2 CH4 CH2 CH4 CH2 CH4 CH2 CH4 CH2 R3 CH1 CH2 R4
SPECIFICATIONS POWER SPECIFICATIONS • Power Rating (Direct Mode): (AES Standard), 3000 W Peak / 1500 W Program / 750 W Continuous • Nominal SPL @ 1m: 122dB SPL Continuous (Direct Mode) • Maximum SPL @ 1m: 125 dB Peak (Direct Mode), 122 dB SPL Continuous (Direct Mode) ELECTRICAL SPECIFICATION • Operating Frequency Range (-10 dB): 37 Hz - 200 Hz • Frequency Response (-3 dB): 43 Hz - 200 Hz • Transducers Low: 18” Subwoofer, 4” voice coil high-power ferrite magnet, weather-resistant cone.
www.altoprofessional.com MANUAL VERSION 1.