QUICKSTART GUIDE ENGLISH ( 2 – 4 ) MANUAL DE INICIO RÁPIDO ESPAÑOL ( 5 – 7 ) GUIDE D’UTILISATION RAPIDE FRANÇAIS ( 8 – 10 ) GUIDA RAPIDA ITALIANO ( 11 – 13 ) KURZANLEITUNG DEUTSCH ( 14 – 16 ) SNELSTARTGIDS NEDERLANDS ( 17 – 19 )
BOX CONTENTS y y y y MIXPACK Express Power cable Quickstart Guide Safety Instructions & Warranty Information booklet CONNECTION DIAGRAM Power Microphones* Headphones* Speaker Speaker NE W 1 Footswitch* Drum Machine* * not included Notes: y y Microphones, headphones, drum machine, footswitch, etc. are not included. To reduce electrical hum at high gain settings, keep the mixer's power supply away from your cables and the mixer's channel inputs.
FEATURES 1. 2. POWER IN – Use the included power cable to connect the mixer to a power outlet. While the power is switched off, plug the power cable into the mixer first, then plug the power cable into a power outlet. POWER SWITCH – Turns the mixer on and off. Turn on the mixer after all input devices have been connected. Make sure the MASTER LEVEL knob is set to "zero" before turning it on. 3. MIC INPUT (XLR / 1/4") – Connect a microphone to these inputs with an XLR or 1/4" cable. 4.
EFFECTS TO HEAR THE EFFECTS ON A CHANNEL: Use the EFFECTS SELECTOR to choose one of the effects below, then turn up the FX AUX1 POST for that channel. # PRESET DESCRIPTION PARAMETER 1 VOCAL 1 Reverb, simulating a room without delay time. Decay time: 450 ms Pre-delay: 0 ms 2 VOCAL 2 Reverb, simulating a room with a small delay time. Decay time: 240 ms Pre-delay: 25 ms 3 VOCAL 3 Reverb, simulating a small space with a slight decay time.
CONTENIDO DE LA CAJA y y y y MIXPACK Express Cable de alimentación Guía de inicio rápido Folleto de instrucciones de seguridad e información sobre la garantía DIAGRAMA DE CONEXIÓN Suministro eléctrico Micrófonos* Auriculares* Altavoce Altavoce NE W 1 Pedal* Caja de ritmos* * no incluido Notas: y y No se incluyen micrófonos, auriculares, caja de ritmos, pedal, etc.
CARACTERÍSTICAS 1. 2. 3. 4. 5. 6. ENTRADA DE ALIMENTACIÓN - Use el cable de alimentación incluido para conectar el mezclador a un tomacorriente alimentado. Con la alimentación eléctrica desconectada, enchufe el cable de alimentación al mezclador primero, y luego al tomacorriente. 1 2 INTERRUPTOR DE ENCENDIDO – Se usa para encender y apagar el mezclador. Encienda el mezclador después de haber conectado todos los dispositivos de entrada.
ECUALIZADOR GRÁFICO – Puede usar estos controles para ajustar la ecualización de la mezcla principal. NIVEL DE MONITOR – Ajusta el volumen de la SALIDA PARA MONITOR y de sus auriculares. NIVEL MAESTRO – Ajusta el volumen de la SALIDA PRINCIPAL. MEDIDORES DE LED – Muestran el nivel de audio de la mezcla principal y la mezcla de monitor. Baje el volumen si el LED +10 se enciende excesivamente. LED DE ENCENDIDO – Se ilumina cuando el mezclador está encendido. 22. 23. 24. 25. 26.
CONTENU DE LA BOÎTE y y y y MIXPACK Express Câble d’alimentation Guide d’utilisation simplifié Consignes de sécurité et informations concernant la garantie SCHÉMA DE CONNEXION Alimentation Casque d’écoute* Microphones* Haut-parleur Haut-parleur NE W 1 Pédale* Module de percussion* * non inclus Remarques : y y Microphones, casque d'écoute, module de percussion, pédale, etc. non inclus.
CARACTÉRISTIQUES 1. 2. 3. 4. 5. ENTRÉE D'ALIMENTATION – Branchez le câble d’alimentation inclus 1 2 pour brancher la console de mixage dans une prise d’alimentation. Lorsque la console de mixage est hors tension, branchez le câble d'alimentation dans la console, puis dans la prise de courant. INTERRUPTEUR D'ALIMENTATION – 18 Cette touche permet de mettre l’appareil sous et hors tension. 19 Branchez la console de mixage après avoir branché tous les appareils.
21. PÉDALE D’EFFET – Lorsqu'une pédale est branchée à cette entrée à l’aide d’un câble TRS de ¼ po (6,35 mm), elle peut être utilisée pour contourner les effets internes de la console de mixage pour tous les canaux. ÉGALISEUR GRAPHIQUE – Vous pouvez utiliser ces commandes afin de régler l’égalisation du mix principal. MONITOR LEVEL – Permet d'ajuster le niveau du volume de la sortie MONITOR OUT et casque. MASTER LEVEL – Ce bouton permet d'ajuster le niveau du volume de la sortie MAIN OUT.
CONTENUTI DELLA CONFEZIONE y y y y MIXPACK Express Cavo di alimentazione Guida rapida Istruzioni di sicurezza e garanzia SCHEMA DEI COLLEGAMENTI Alimentazione Microfoni* Cuffie* Altoparlante Altoparlante NE W 1 Pedale* Drum Machine* * non in dotazione Note: y y Microfoni, cuffie, drum machine, pedale, ecc. non in dotazione. Per ridurre il ronzio elettrico con impostazioni elevate di guadagno, tenere l’alimentazione del mixer lontana dal cavo della chitarra e dagli ingressi canale del mixer.
CARATTERISTICHE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. POWER IN (INGRESSO ALIMENTAZIONE) – Servirsi del cavo di alimentazione in dotazione per collegare il mixer ad una presa di alimentazione. Ad alimentazione spenta, collegare il cavo d'alimentazione innanzitutto nel mixer, quindi ad una presa elettrica. 1 2 INTERRUTTORE DI ALIMENTAZIONE (POWER) – Accende e spegne il mixer.
EFFETI PER SENTIRE GLI EFFETTI SU UN CANALE: servirsi del SELETTORE DI EFFETTI per scegliere uno degli effetti elencati qui di seguito e alzare FX AUX1 POST per quel canale. # PRESET DESCRIZIONE PARAMETRO 1 VOCE 1 Riverbero, che simula una sala con un piccolo tempo di delay. 2 VOCE 2 Riverbero, che simula una sala con un piccolo tempo di delay. Tempo di decadenza: 240 ms Pre-delay: 25 ms 3 VOCE 3 Riverbero, che simula un piccolo spazio, con un leggero tempo di decadenza.
LIEFERUMFANG y y y y MIXPACK Express Netzkabel Kurzanleitung Sicherheitshinweise und Garantieinformationen ANSCHLUSSÜBERSICHT Steckdose Mikrofone* Kopfhörer* Lautsprecher Lautsprecher NE W 1 Fuss-Schalter* Drum Machine* * nicht im Liefterumfang enthalten Hinweise: y y Mikrofone, Kopfhörer, Drum Machine, Fuss-Schalter, etc. sind nicht im Lieferumfang enthalten.
FUNKTIONEN 1. 2. 3. 4. 5. 6. 7. POWER IN – Verwenden Sie das mitgelieferte Stromkabel, um den Mixer 1 2 mit einer Steckdose zu verbinden. Stellen Sie sicher, dass das Gerät ausgeschaltet ist. Verbinden Sie das Stromkabel mit dem Mixer und stecken das Stromkabel dann in eine Steckdose. POWER SWITCH – Schaltet das Gerät ein/aus. Schalten Sie den Mixer ein, nachdem alle Eingabegeräte 18 angeschlossen wurden.
EFFEKTE SO HÖREN SIE DIE EFFEKTE EINES KANALS: Verwenden Sie den EFFEKTWAHLSCHALTER, um einen der unten angeführten Effekte auszuwählen, und drehen Sie anschließend FX AUX1 POST für diesen Kanal auf. # PRESET 1 GESANG 1 Reverb, der einen Raum ohne Verzögerungszeit simuliert. Abklingzeit: 450 ms Pre-Delay: 0 ms 2 GESANG 2 Reverb, der einen Raum mit einer kurzen Verzögerungszeit simuliert.
INHOUD VAN DE DOOS y y y y MIXPACK Express Stroomkabel Snelstartgids Veiligheidsvoorschriften & boekje met informatie over de garantie VERBINDINGSDIAGRAM Stroom Microfoons* Hoofdtelefoons* Luidsprekers Luidsprekers NE W 1 Voetschakelaar* * niet inbegrepen Drumcomputer* Opmerkingen: y y Microfoons, hoofdtelefoons, drumcomputer, voetschakelaar, enz. zijn niet inbegrepen.
EIGENSCHAPPEN 1. 2. 3. 4. 5. 6. POWER IN Gebruik de bijgevoegde stroomkabel om 1 2 verbinding te maken tussen de mixer en een stopcontact. Terwijl de stroom uitstaat, plug je de stroomkabel eerst in de mixer, vervolgens kun je de stroomkabel in het stopcontact plaatsen. POWER SWITCH - Zet de mixer 18 aan en uit. Zet de mixer aan nadat 19 alle input devices verbonden zijn. Zorg ervoor dat de MASTER LEVEL regelaar op "nul" staat 20 alvorens hem aan te zetten.
21. FOOT-SWITCH - Wanneer een vergrendelde schakelaar is verbonden met deze jack door middel van een 1/4" TRS kabel, kan deze ingedrukt worden om alle kanalen de mixer's interne effectenprocessor te laten omzeilen. GRAPHIC EQUALIZER - U kunt gebruik maken van deze om te compenseren voor de Main Mix. 22. 23. MONITOR LEVEL - Stelt het volume van de monitor-uitgang en een hoofdtelefoon. 24. 25. MASTER LEVEL - Stelt het volume van de hoofduitgang.
TECHNICAL SPECIFICATIONS MIXER SECTION: FREQUENCY RESPONSE: 10 Hz – 55 KHz (+ 3 dB) IMPEDANCE: 3.9 KΩ (mic input) > 10 KΩ (all other inputs) 2.2 KΩ (tape out) 120 Ω (all other outputs) SNR: > 94 dB THD+N: 0.04% at 0 dBu, 1 KHz (mono input channels) 0.015% at 0 dBu, 1 KHz (stereo input channels) EQUALIZATION: High shelving: + 15 dB @ 12 KHz Low shelving: + 15 dB @ 80 Hz 7-band graphic equalizer: + 15 dB @ 63 Hz, 160 Hz, 400 Hz, 1 KHz, 2.5 KHz, 6.