Hot Food Drop-In Wells Electric 500-HWI/D4 100-HW/D6 300-HWI/D6 400-HW/D4 Models: 100-HW/D4/D6/D443/D643 100-HWLF/D4/D6 200-HW/D4/D6/D443/D643 200-HWLF/D4/D6 200-HWI/D4/D6/D443/D643 200-HWILF/D4/D6 300-HW/D4/D6/D443/D643 300-HWLF/D4/D6 300-HWI/D4/D6/D443/D643 300-HWILF/D4/D6 400-HW/D4/D6 400-HWLF/D4/D6 400-HWI/D4/D6 400-HWILF/D4/D6 500-HW/D4/D6 500-HWLF/D4/D6 500-HWI/D4/D6 500-HWILF/D4/D6 • INSTALLATION • OPERATION • MAINTENANCE W164 N9221 Water Street • P.O.
Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Procedures and Precautions . . . . . . . . . . . . . 2 Installation Installation Requirements . . . . . . . . . . . Leveling . . . . . . . . . . . . . . . . . . . . . . . . . Options & Accessories . . . . . . . . . . . . .
DELIVERY UNPACKING This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier. See Transportation Damage and Claims section located in this manual. • This appliance, complete with unattached items and accessories, may have been delivered in one or more packages.
SAFETY PROCEDURES AND PRECAUTIONS Knowledge of proper procedures is essential to the safe operation of electrically and/or gas energized • This appliance is intended to cook, hold or process equipment. In accordance with generally accepted product safety labeling guidelines for potential other use for this appliance is authorized and is therefore considered dangerous. The appliance hazards, the following signal words and symbols may be used throughout this manual.
INSTALLATION DANGER CAUTION Improper installation, alteration, adjustment, service, cleaning, or maintenance could result in property damage, severe injury, or death. METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. Read the installation, operating and maintenance instructions thoroughly before installing, servicing, or operating this equipment.
INSTALLATION DIMENSIONS 100-HW/D4, D6, D443, D643 6-5/16" (159mm) 8-3/16" (207mm) 5-9/16" (140mm) 7-7/16" (189mm) 4-3/8" (111mm) 6-3/8" (162mm) 4-3/8" (111mm) 6-3/8" (162mm) 4-7/8" (123mm) 4" (102mm) 4" (102mm) 4-15/16" (125mm) 6-15/16" (175mm) 6-7/16" (163mm) 1/4" (5mm) WELL 27-1/4" (691mm) 4" (102mm) 4-15/16" (125mm) 100-HW/D643 100-HW/D443 6" (152mm) 4-15/16" (125mm) Ø 1/4" (5mm) 4" (102mm) 6" (152mm) 4-13/16" (122mm) 4-7/8" (123mm) 4-15/16" (125mm) 10-13/16" (274mm) /D443 AND
INSTALLATION DIMENSIONS 200-HW/D4 & 200-HW/D6 6-15/16" (175mm) 7-5/16" (185mm) FLANGE 4-3/8" (111mm) WELL 9/16" (14mm) FLANGE FLANGE 4-13/16" (122mm) 6-3/8" (162mm) 4-13/16" (122mm) WELL 27-1/4" (691mm) 29-1/16" (738mm) WELL 9/16" (14mm) 4-3/8" (111mm) FLANGE WELL 6-3/8" (162mm) WELL 4-13/16" (122mm) WELL 5" (127mm) 6" (152mm) 7-7/16" (189mm) 4-13/16" (122mm) 6-15/16" (175mm) CONDUIT WHEN EXITING BACK 9-3/16" (233mm) 27-1/4" (691mm) 29-1/16" (738mm) 9/16" (14mm) 9/16" (14mm)
INSTALLATION DIMENSIONS 200-HWI/D4, D6, D443, D643 27-5/8" (701mm) 12" (304mm) WELL 7-5/16" (185mm) 7-5/16" (185mm) 9-5/16" (236mm) 9-1/4" (234mm) 5-9/16" (141mm) 5-9/16" (141mm) 7-9/16" (191mm) 7-1/2" (189mm) 4-3/8" (111mm) 4-3/8" (111mm) 6-3/8" (162mm) 6-3/8" (162mm) 1-7/8" (46mm) 4-1/8" (104mm) WELL 27-1/4" (691mm) 29-1/16" (738mm) 1-7/8" (46mm) 4-1/8" (104mm) WELL 22-1/16" (559mm) FLANGE 5/8" (15mm) 1-7/8" (46mm) 4-1/8" (104mm) WELL 27-1/4" (691mm) 29-1/16" (738mm) 1-7/8" (4
INSTALLATION DIMENSIONS 300-HW/D4, D6, D443, D643 40-15/16" (1039mm) 37-7/8" (962mm) 1-9/16" (39mm) WELL 40-15/16" (1039mm) 6" (152mm) 9/16" (14mm) WELL 6-15/16" (175mm) 9/16" (14mm) 9/16" (14mm) FLANGE FLANGE 4-13/16" (122mm) 4" (102mm) 4" (102mm) 4-15/16" (125mm) 4-15/16" (125mm) 300-HW/D443 WELL CONDUIT WHEN EXITING BOTTOM FLANGE 4-13/16" (122mm) 6-3/8" (162mm) 5" (127mm) CONDUIT WHEN EXITING BACK 9/16" (14mm) FLANGE 7-1/2" (190mm) 4-13/16" (122mm) 22-1/16" (559mm) 4-13/16" (
INSTALLATION DIMENSIONS 300-HWI/D4, D6, D443, D643 40-7/8" (1038mm) 12" (304mm) WELL 5-9/16" (141mm) 4-3/8" (111mm) WELL 1-7/8" (46mm) 6-3/8" (162mm) 9-1/4" (234mm) 1-7/8" (46mm) 7-1/2" (189mm) 7-1/2" (189mm) 6-3/8" (162mm) WELL 4-13/16" (122mm) 40-7/8" (1038mm) 12" (304mm) 4-1/8" (104mm) FLANGE 5/8" (15mm) 4-13/16" (122mm) WELL 27-1/4" (691mm) 29-1/16" (738mm) 4-1/8" (104mm) 4-13/16" (122mm) 4-13/16" (122mm) WELL 1-1/2" (38mm) 4" (102mm) 4" (102mm) 4" (102mm) 4" (102mm) 4-15/16" (
INSTALLATION DIMENSIONS 400-HW/D4 & 400-HW/D6 54" (1371mm) 1-9/16" (39mm) 50-15/16" (1294mm) WELL 7-5/16" (185mm) 9-5/16" (235mm) 5-9/16" (140mm) 7-9/16" (191mm) 4-3/8" (111mm) 6-3/8" (162mm) 1-7/8" (46mm) WELL 4-1/8" (104mm) 20-3/16" (512mm) 22-1/16" (559mm) 1-7/8" (46mm) 4-1/8" (104mm) WELL CONDUIT WHEN EXITING BOTTOM 20-3/16" (512mm) 22-1/16" (559mm) 6" (152mm) WELL CONDUIT WHEN EXITING BACK 1-1/2" (37mm) WELL WELL 9/16" (14mm) FLANGE 6" (152mm) 9/16" (14mm) FLANGE 4-13/16" (
INSTALLATION DIMENSIONS 400-HWI/D4 & 400-HWI/D6 53-3/4" (1364mm) 1-5/16" (33mm) 12" (304mm) WELL 7-5/16" (185mm) 9-5/16" (236mm) 5-9/16" (141mm) 7-9/16" (191mm) 4-3/8" (111mm) 6-3/8" (162mm) 10-13/16" (274mm) WELL WELL 6" (152mm) 1-7/8" (46mm) CONDUIT WHEN EXITING BACK 6" (152mm) WELL 4-1/8" (104mm) 20-3/16" (512mm) 22-1/16" (559mm) 5/8" (15mm) FLANGE 1-7/8" (46mm) WELL 4-1/8" (104mm) 20-3/16" (512mm) 22-1/16" (559mm) WELL 5/8" (15mm) FLANGE 20-3/16" (512mm) 23-3/16" (588mm) 4-1
INSTALLATION DIMENSIONS 500-HW/D4 & 500-HW/D6 67-1/16" (1702mm) 63-15/16" (1625mm) 1-9/16" (39mm) 7-5/16" (185mm) 9-5/16" (235mm) 5-9/16" (140mm) 7-9/16" (191mm) 4-3/8" (111mm) 6-3/8" (162mm) 1-7/8" (46mm) 4-1/8" (104mm) WELL 22-1/16" (559mm) 20-3/16" (512mm) 1-7/8" (46mm) WELL 4-1/8" (104mm) 20-3/16" (512mm) 22-1/16" (559mm) 9/16" (14mm) FLANGE WELL 1-1/2" (37mm) 9/16" (14mm) FLANGE WELL WELL 20-3/16" (512mm) 23-1/8" (586mm) WELL 65-3/4" (1670mm) 11/16" (16mm) 11/16" (16mm) FLAN
INSTALLATION DIMENSIONS 500-HWI/D4 & 500-HWI/D6 1-5/16" (33mm) 7-5/16" (185mm) 9-5/16" (236mm) 66-13/16" (1696mm) 5-9/16" (141mm) 7-9/16" (191mm) 12" (304mm) 4-3/8" (111mm) 6-3/8" (162mm) WELL WELL WELL 1-7/8" (46mm) WELL 4-1/8" (104mm) 20-3/16" (512mm) 22-1/16" (559mm) 5/8" (15mm) FLANGE 1-7/8" (46mm) WELL 4-1/8" (104mm) 20-3/16" (512mm) 22-1/16" (559mm) 5/8" (15mm) FLANGE WELL 20-3/16" (512mm) 23-3/16" (588mm) 10-13/16" (274mm) 4-13/16" (122mm) 6" (152mm) CONDUIT WHEN EXITING
INSTALLATION ROUGH CUT OPENINGS COUNTER CUTOUT (W x D) CONTROL BOX CUTOUT* (H x W x D) 100-HW/D4 or D6 one full-size 100-HWLF/D4 or D6 one full-size 14-1/4" x 22-1/2" (363mm x 572mm) 4-1/4" x 5-1/4" x 10-13/16" (108mm x 133mm x 274mm) 100-HW/D443 or D643 one full & one third-size pan 14-1/4" x 29-1/2" (363mm x 749mm) 4-1/4" x 5-1/4" x 10-13/16" (108mm x 133mm x 274mm) 200-HW/D4 or D6 two full-size pans 200-HWLF/D4 or D6 two full-size pans 27" x 22-1/2" (686mm x 572mm) 4-1/4" x 5-1/4" x 10-13/16" (
INSTALLATION CONTROL CONDUIT 6" (152mm) Minimum Clearance 6" (152mm) Minimum Clearance Cord location at bottom Cord location at back * A llow a minimum of 6" (152mm) clearance from back/bottom of control box to tether bend PRODUCT\PAN CAPACITY (based on 4" deep pans) Max. Capacity Max.
INSTALLATION RE MOT E CONTROL H OU S IN G M O U N TIN G IN S TRU C TION S Apply a food grade silicone under the edge of the hot well support flange. DECOR FACE SCREWS 1. Cut an appropriate sized opening in the location where the control is to be positioned. See chart on page 13 for cutout size. 4. Route control housing through opening cut in step 1. Secure the décor face housing to the control housing using the screws removed in step 3. 2.
INSTALLATION ELECTRICAL CONNECTION 1. A n identification tag is permanently mounted on the appliance. 2. T his appliance is equipped with a three-prong grounding plug. For your protection against shock hazard this appliance should be plugged directly into a properly grounded threeprong receptacle. Do not cut or remove the grounding prong from this plug. Plug the unit into a properly grounded receptacle ONLY, positioning the unit so that the plug is easily accessible in case of an emergency.
INSTALLATION ELECTRICAL ELECTRICAL SPECIFICATIONS (Refer to the wire diagrams sent with the unit) 1 Phase, 50/60 Hz Voltage Amps kW nema 5-15p 15a-125v plug nema 5-20p 20a-125v plug nema l5-30p 30a-125v plug nema 6-15p 15a-250v plug cee 7/7 250V plug rated ch2-16p plug rated 250V bs1363 plug rated 100-HW/D4, /D6 120V 5.0 0.6 208V 240V 2.2 2.5 0.5 0.6 230V 2.6 0.6 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 100-HW/D443, /D663 120V 6.8 0.8 208V 240V 2.9 3.4 0.6 0.8 230V 3.5 0.
OPERATING INSTRUCTIONS 1. DO NOT ADD WATER TO HOT WELL Halo Heat ® hot wells maintain a constant and gentle temperature. Adding water is not recommended since water will accelerate the deterioration of the product and may damage the unit voiding the warranty. 2. PLACE PAN DIVIDERS AND EMPTY PANS IN THE WELLS NOTE: No matter what type of pan configuration chosen, pan separator bars or divider bars must be used to close all gaps between pans, and all gaps between the pans and the edges of the wells.
G E N E R A L HO L DING GUIDEL INES Chefs, cooks and other specialized food service personnel employ varied methods of cooking. Proper holding temperatures for a specific food product must be based on the moisture content of the product, product density, volume, and proper serving temperatures. Safe holding temperatures must also be correlated with palatability in determining the length of holding time for a specific product.
CLEANING AND PREVENTATIVE MAINTENANCE PROTECTING STAINLESS STEEL SURFACES It is important to guard against corrosion in the care of stainless steel surfaces. Harsh, corrosive, CLEANING AGENTS Use non-abrasive cleaning products designed for use on stainless steel surfaces. Cleaning agents must be chloride-free compounds and must not or inappropriate chemicals can completely destroy the contain quaternary salts. Never use hydrochloric acid (muriatic acid) on stainless steel surfaces.
CARE AND CLEANING The cleanliness and appearance of this appliance will contribute considerably to operating efficiency and savory, appetizing food. Good equipment kept clean works better and lasts longer. DANGER Disconnect unit from power source before cleaning or servicing. Failure to observe this precaution can cause electrical shock and personal injury. NOTE: Always allow the appliance to cool before cleaning. CLEAN THE APPLIANCE DAILY.
SANITATION Food flavor and aroma are usually so closely related that it is difficult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food flavor. Cleanliness, top operating efficiency, and appearance of equipment contribute considerably to savory, appetizing foods. Good equipment that is kept clean, works better and lasts longer. Most food imparts its own particular aroma and many foods also absorb existing odors.
SERVICE CONTROL SERVICE VIEW (100-HW shown ) 3 14 2 19 12 5 17 13 8 17a 17b 17b 18 18 17c 11 17d 10 9 15 4 1 Item 1 2 3 4 5 6 7 8 9 10 11 12 Part KN-36424 1015723 TU-33178 CC-36859 1017287 LI-37215 PE-36566 TA-24637 CR-34646 SC-22500 WS-2768 NU-23909 7 Description KNOB, T-STAT CONTROL SHELL, CONTROL POD, 1 KNOB CONDUIT, FLEXIBLE, 6 FT CONTROL PLATE, FACE LIGHT, INDICATOR PANEL OVERLAY, CONTROL TAPE, VHB, FOAM, 1/2" WIDE CONNECTOR-5 CONDUCTOR SCREW 6-32 x 1/4" PAN HD WASHER, #6, LOCK NUT,
SERVICE EXTERIOR SERVICE VIEW (100-HW shown ) 1 2 2a 2b 5 2c 5a 2d 2e 3 7 4 4a 4b 4c 11 9 12 6 10 8 Item 1 2 2a 2b 2c 2d 2e 3 4 4a 4b Part 11318 5017271 5017613 5017684 5017703 5017708 5018740 IN-24588 1015827 1016193 1016204 Description DIVIDER, PAN, SHORT WELDMENT, D6, STD FLANGE WELDMENT, D4, STD FLANGE WELDMENT, D643, STD FLANGE WELDMENT, D6, WIDE FLANGE WELDMENT, D4, WIDE FLANGE WELL SPOT, D443, STD FLANGE INSULATION WRAPPER, 1 WELL, 6" DEEP WRAPPER, 1 WELL, 4" DEEP WRAPPER, 1 WELL, 6" DEE
SERVICE CONTROL SERVICE VIEW (200-HW shown ) 10 13 13a 13a 13b 20 1 13c 13c 22 21 19 13d 16 6 17 5 9 2 18 18 11 14 3 15 15 12 7 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 13a 8 Part 1017287 1017303 CC-36859 1015805 BU-34606 BU-3964 KN-36424 LI-37215 PE-36566 TU-33178 CR-34646 TA-24637 CD-3232 5014997 4 Description PLATE, FACE SHELL, CONTROL POD DEEP, 1 KNOB CONTROL BOX, REMOTE, DECOR FACE, 1 KNOB BUSHING, STRAIGHT, STRAIN RELIEF BUSHING, STRAIGHT, STRAIN RELIEF KNOB, T-STAT CONTROL LIGHT, I
SERVICE EXTERIOR SERVICE VIEW (200-HW shown ) 1 2 1c 3 1b 1d 4 1e 4a 1f 5 6 6a 15 6b 10 6c 11 9 12 13 7 14 8 Item 1 1b 1c 1d 1e 1f 2 3 4 4a 5 6 6a Part 5018588 5018589 5018590 5018591 5018695 5018696 11318 16019 EL-36317 EL-36860 IN-24588 1015828 1016194 Description WELL, D4, STD WELL, D6, STD FLANGE WELL, D4, WIDE FLANGE WELL, D6, WIDE FLANGE WELL, D443, STD FLANGE WELL, D643, STD FLANGE DIVIDER, PAN, SHORT DIVIDER, PAN ELEMENT, HEATING PAD ELEMENT, HEATING PAD, 4/3 MODEL INSULATION W
SERVICE CONTROL SERVICE VIEW (200-HWI shown ) 15 7 2 16 20 16a 18 16b 17 16c 9 16d 10 19 3 11 8 13 5 6 12 1 14 Item 1 2 3 5 6 7 8 9 10 11 12 13 Part LI-37215 BU-34606 BU-3964 SC-22766 PG-35411 1015724 CR-34646 CC-36859 TA-24637 PE-36566 KN-36424 SC-22500 Description LIGHT, INDICATOR BUSHING, STRAIGHT, STRAINFRELIE BUSHING, STRAIGHT, STRAINFRELIE SCREW, M5 x 0.8 x 10mm PAN 1/4" HOLE PLUG SHELL, CONTROL POD, 2 KNOB CONNECTOR-5 CONDUCTOR CONTROL, DETENT, 650F MAX TAPE, VHB, FOAM, 1/2" x 9.
SERVICE EXTERIOR SERVICE VIEW (200-HWI shown ) 10 1 1a 1b 1c 1d 3 1e 3a 9 11 11a 11c 11b 4 8 7 5 6 2 Item 1 1a 1b 1c 1d 1e 2 3 3a 4 5 Part 5017704 5017612 5017709 5017614 5018690 5018691 RI-2097 EL-36317 EL-36860 SC-22281 1016034 Description WELDMENT, D6, WIDE FLANGE WELDMENT, D6, STD FLANGE WELDMENT, D4, WIDE FLANGE WELDMENT, D6, WIDE FLANGE WELDMENT, D643, STD FLANGE WELDMENT, D443, STD FLANGE #42 STAINLESS RIVET ELEMENT, FOIL HEATING PAD ELEMENT, HEATING PAD, 810W SCREW, M5 x 0.
SERVICE CONTROL SERVICE VIEW (300-HW shown ) 2 1 1a 1b 5 12 1c 1d 20 21 9 19 10 7 3 15 6 22 4 23 11 8 13 Item 1 1a 1b 1c 1d 2 3 4 5 6 7 8 9 10 Part 5014997 5016998 5017529 CD-33840 CD-3922 TU-33178 BU-3964 BU-34606 1017312 CR-34646 CC-36859 1017287 PG-35411 RL-34279 18 17 16 14 Description BS 1363 CORDSET FERRULE ASSEMBLY CH2-16P CORDSET FERRULE ASSEMBLY NEMA 5-20P CORDSET FERRULE ASSEMBLY CORDSET 15A 208-240V CORDSET-16AWG, 3/C, INT’L HARM CONDUIT FLEX LIQUID TIGHT, 3FT BUSHING, STRAI
SERVICE EXTERIOR SERVICE VIEW (300-HW shown ) 3 1 2 4 1a 4a 1b 1c 5 1d 1e 15 12 7 7a 7c 9 7b 14 11 10 Item 1 1a 1b 1c 1d 1e 2 3 4 4a 5 6 Part 5018554 5018555 5018556 5018557 5018558 5018559 11318 16019 EL-36317 EL-36860 IN-24588 RI-2097 Description WELL, D4, STD WELL, D6 STD WELL, D443 STD WELL, D643 STD WELL, D4 WIDE FLANGE WELL, D6, WIDE FLANGE PAN DIVIDER SHORT DIVIDER, PAN ELEMENT, HEATING PAD ELEMENT, HEATING PAD, 4/3 MODEL INSULATION #42 STAINLESS RIVET Qty 1 1 1 1 1 1 6 2 3 3 1 10
SERVICE CONTROL SERVICE VIEW (300-HWI 1 shown ) 6 18 17 3 7 20 7b 19 7c 7a 5 13 10 4 12 11 9 2 15 8 Item 1 2 3 4 5 6 7 7a 7b 7c 7d 8 Part SC-22271 CC-36859 1015725 CL-37245 BU-33505 BU-34606 CD-33366 5014997 5016998 CD-33840 CD-3922 WS-2768 7d Description SCREW, M4 x 0.
SERVICE EXTERIOR SERVICE VIEW (300-HWI 2 shown ) 1 2a 2b 2c 2d 3 2e 3a 2d 2d 4 5 5a 5b 5c 7 11 6 8 10 9 Item 1 2 2a 2b 2c 2d 2e 3 3a 4 5 Part 11318 5017216 5017615 5017692 5017696 5017705 5017710 EL-36317 EL-36860 IN-24588 1015670 Description PAN DIVIDER SHORT WELDMENT, D6, STANDARD FLANGE WELDMENT, D4, STANDARD FLANGE WELDMENT, D643, STANDARD FLANGE WELDMENT, D443, STANDARD FLANGE WELDMENT, D6, LARGE FLANGE WELDMENT, D4, LARGE FLANGE ELEMENT, FOIL HEATING PAD, 600W ELEMENT, FOIL HEATING PAD
SERVICE CONTROL SERVICE VIEW (400-HW shown ) 23 1 1a 9 7 1b 1c 10 1d 17 8 12 5 15 2 3 18 13 14 22 19 4 16 20 11 Item 1 1a 1b 1c 1d 2 3 4 5 6 7 8 9 10 Part 5013668 5014997 5016998 CD-33840 CD-3922 1017288 SC-22926 CC-36859 CL-37245 1015806 1015724 BU-33505 BU-34606 CR-34646 21 6 Description NEMA L5-30P CORDSET FERRULE ASSEMBLY BS 1363 CORDSET FERRULE ASSEMBLY CH2-16P CORDSET FERRULE ASSEMBLY CORDSET 15A 208-240V CORDSET-16AWG, 3/C, INT’L HARM PLATE, FACE SCREW, M5 x 0.
SERVICE EXTERIOR SERVICE VIEW (400-HW shown ) 3 1 2 1a 1b 4 1c 15 5 6 6a 10 12 14 13 7 9 8 Item 1 1a 1b 1c 2 3 4 5 6 6a Part 5018600 5018601 5018602 5018603 11318 16019 EL-36317 IN-24588 1016162 1016168 Description WELL, D4, STD WELL, D6 STD WELL, D4 WIDE FLANGE WELL SPOT DIVIDER, PAN, SHORT DIVIDER, PAN ELEMENT, FOIL HEATING PAD INSULATION WRAPPER, 4 WELL, 6" DEEP WRAPPER, 4 WELL, 4" DEEP 11 Qty 1 1 1 1 8 3 4 1 1 1 Item 7 8 9 10 11 12 13 14 15 Part 1016034 RI-2097 WS-22301 NU-23909 SC-36
SERVICE CONTROL SERVICE VIEW (400-HWI shown ) 17 5 8 23 4 6 14 1 1a 3 20 1b 1c 22 12 10 7 1d 14 11 19 21 Item 1 1a 1b 1c 1d 3 4 5 6 7 8 9 10 Part 5014997 5016998 CD-33840 CD-33366 CD-3922 CC-36859 1015726 SC-22271 BU-33505 BU-34606 CR-34646 KN-36424 LI-37215 15 13 9 Description BS 1363 CORDSET FERRULE ASSEMBLY CH2-16P CORDSET FERRULE ASSEMBLY CORDSET 15A 208-240V CORDSET 6' 125V 30A 10/3 CORDSET-16AWG, 3/C, INT’L HARM CONTROL SHELL, CONTROL POD, 4 KNOB SCREW, M4 x 0.
SERVICE EXTERIOR SERVICE VIEW (400-HWI shown ) 6 3 6a 6b 6c 4 8 12 9 2 2a 1 7 13 11 Item 1 2 2a 3 4 5 6 6a 6b Part 1016034 1016162 1016168 11318 SC-22281 SC-22926 5017611 5017616 5017711 Description BOX, CONNECTION WRAPPER, 4 WELL, 6" DEEP WRAPPER, 4 WELL, 4" DEEP PAN DIVIDER SHORT SCREW, M5 x 0.8 x 16mm FLAT SCREW, M5 x 0.
SERVICE CONTROL SERVICE VIEW (500-HW shown ) 22 2 2a 15 8 1 2b 2c 4 2d 18 14 6 17 3 13 16 9 10 24 Item 1 2 2a 2b 2c 2d 3 4 5 6 7 8 9 10 Part 1017288 5013668 5016998 CD-33840 CD-3922 5014997 SC-22926 SC-22271 CC-36859 1015806 SC-22500 CR-34646 TA-24637 SC-22766 11 7 20 Description PLATE, FACE NEMA L5-30P CORDSET FERRULE ASSEMBLY CH2-16P CORDSET FERRULE ASSEMBLY CORDSET 15A 208-240V CORDSET-16AWG, 3/C, INT’L HARM BS 1363 CORDSET FERRULE ASSEMBLY SCREW, M5 x 0.8 x 16mm HEX SCREW, M4 x 0.
SERVICE EXTERIOR SERVICE VIEW (500-HW shown ) 1 2 5 4 4a 4b 4c 15 3 6 9 6a 7 10 11 Item 1 2 3 4 4a 4b 4c 5 6 Part 11318 16019 IN-24588 5018546 5018547 5018548 5018549 EL-37233 1015717 Description DIVIDER, PAN, SHORT DIVIDER, PAN INSULATION WELL, D4, STD WELL, D6, WIDE FLANGE WELL, D4 WIDE FLANGE WELL, D6 WIDE FLANGE ELEMENT, HEATING PAD WRAPPER, 5 WELL, 6" DEEP Qty 10 4 1 1 1 1 1 2 1 Item 6a 7 8 9 10 11 15 8 Part 1016196 1016034 WS-22301 NU-23909 SC-36973 RI-2097 1017049 Description WRAPPER,
SERVICE CONTROL SERVICE VIEW (500-HWI 2 11 9 shown ) 1 3 1a 1b 6 1c 4 13 1d 5 21 22 18 23 10 7 12 14 15 20 Item 1 1a 1b 1c 1d 2 3 4 5 6 7 8 9 10 Part 5013668 CD-33840 5014997 5016998 CD-3922 TU-33178 BU-34606 BU-33505 1015727 NU-23909 SC-22766 SC-22766 SC-22271 CR-34646 8 Description NEMA L5-30P CORDSET FERRULE ASSEMBLY CORDSET 15A 208-240V BS 1363 CORDSET FERRULE ASSEMBLY CH2-16P CORDSET FERRULE ASSEMBLY CORDSET-16AWG, 3/C, INT’L HARM CONDUIT, FLEXIBLE BUSHING, STRAIN RELIEF BUSHING, STR
SERVICE EXTERIOR SERVICE VIEW (500-HWI shown ) 1 3 2 2a 13 2b 2c 4 9 10 5 5a 8 7 11 6 14 12 Item Part Description Qty Item Part Description Qty 1 2 2a 2b 2c 3 4 5 5a 6 DIVIDER, PAN, SHORT WELDMENT, D6, WIDE FLANGE WELDMENT, D4, WIDE FLANGE WELDMENT, D6 STD FLANGE WELDMENT, D4 STD FLANGE ELEMENT, FOIL HEATING PAD INSULATION, 33.
MN-37234 (Rev.
MN-37234 (Rev.
TRANSPORTATION DAMAGE and CLAIMS 1. 2. 3. 4. 5. 6. 7. 8. All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be established on the part of the shipper.
