Heated Display Cases ® Full Service or Self Service Models: HN2-48; HN2SYS-48 HN2-48/P; HN2SYS-48/P HN2SYS-48 HN2-48 HN2SYS-72 HN2-72 HN2SYS-96 HN2-96 HN2-72; HN2SYS-72 HN2-72/P; HN2SYS-72/P HN2-72/PL; HN2SYS-72/PL HN2-72/PR; HN2SYS-72/PR HN2-96; HN2SYS-96 HN2-96/PL; HN2SYS-96/PL HN2-96/PR; HN2SYS-96/PR • INSTALLATION • OPERATION • MAINTENANCE W 1 6 4 N 9 2 2 1 W a t e r S t r e e t • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA PHONE: 262.251.3800 • 800.558.8744 USA/CANADA FAX: 262.
® D E L I V E RY U N PA C K I N G This Alto-Shaam appliance has been thoroughly tested and inspected to insure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier. See Transportation Damage and Claims section located in this manual. This appliance, complete with unattached items and accessories, may have been delivered in one or more packages.
SAFETY PROCEDURES AND PRECAUTIONS Knowledge of proper procedures is essential to the safe operation of electrically and/or gas energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols may be used throughout this manual. Used to indicate the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the warning included with this symbol is ignored.
I N S TA L L AT I O N METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. IMPROPER INSTALLATION, ALTERATION, ADJUSTMENT, SERVICE OR MAINTENANCE COULD RESULT IN SEVERE INJURY, DEATH OR CAUSE PROPERTY DAMAGE. TO PREVENT PERSONAL INJURY, USE CAUTION WHEN MOVING OR LEVELING THIS APPLIANCE.
I N S TA L L AT I O N S I T E I N S TA L L AT I O N 37-3/4" (958mm) 37-3/4" (958mm) 3-1/8" (77mm) ELECTRICAL CORD 14-15/16" (378mm) 52-3/8" (1328mm) 51-3/4" (1312mm) 41-15/16" (1065mm) 13-1/2" (344mm) 6-13/16" (172mm) HN2 PROFILE 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER HN2SYS-48 48" (1219mm) 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER HN2SYS-72 72" (1829mm) 14-15/16" (378mm) 30-3/4" (781mm) 37-3/4" (958mm) 3-1/8" (77mm) ELECTRICAL CORD 14-15/16" (378mm) 52-3/8" (1328mm) HN2SYS PROFILE
I N S TA L L AT I O N ELECTRICAL CONNECTION The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National Electrical Code and applicable local codes. To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the current edition of the National Electrical Code ANSI/NFPA No. 70.
I N S TA L L AT I O N HN2 & HN2SYS SERIES — OPTIONS & ACCESSORIES DESCRIPTION END PANELS, 1” HN2SYS HN2-48 LAMINATE , BLACK SERIES contact factory contact factory contact factory GU-33384 GU-33384 GU-33384 FOR PL / PR UNITS GL-26984 GL-26984 GL-26984 RIGHT- HAND GL-26948 GL-26948 GL-26948 LEFT- HAND GL-26949 GL-26949 GL-26949 5001781 5001781 5001781 BRUSHED STAINLESS STEEL 5004595 5004596 5004597 CUSTOM COLOR 5004598 5004599 5004600 BRUSHED STAINLESS STEEL 5004601 5004602
O P E R AT I N G I N S T R U C T I O N S U S E R S A F E T Y I N F O R M AT I O N METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. The Alto-Shaam heated display case is intended for use in commercial establishments by qualified operating personnel where all operators are familiar with the purpose, limitations, and associated hazards of this appliance.
O P E R AT I N G I N S T R U C T I O N S O P E R AT I N G P R O C E D U R E S 1. DO NOT ADD WATER TO DISPLAY CASE Halo Heat display cases maintain a constant but gentle temperature and eliminate much of the moisture loss associated with conventional display cases. Because of this gentle heat, it is not necessary to add water to the display case. As a matter of fact, adding water is not recommended since water will accelerate the deterioration of the product, and may damage the unit voiding the warranty. 2.
O P E R AT I N G I N S T R U C T I O N S Indicator Lights LI-3027 Light Switch SW-33896 Cutting Board Bracket Thermostats TT-3498 BT-2342 Operator/Control side with cutting board Electrical Cord CD-3291 Plug Thermostat TT-3498 PG-3267 Cutting Board HN2-48, HN2SYS-48 – 4016 (1) HN2-72, HN2SYS-72 – 4017 (1) HN2-96, HN2SYS-96 – 4016 (2) #894 • HN2 Series Operation & Care Manual • 9
O P E R AT I N G I N S T R U C T I O N S PAN CONFIGURATIONS • HEATED DISPLAY CASES HN2-72 HN2-96 HN2-48 GN 1/2 ONE-HALF SIZE PAN 12" x 10" x 2-1/2" (325mm x 265mm x 65mm) GN1/2 TWO-THIRDS SIZE PAN 12" x 14" x 2-1/2" (325mm x 352mm x 65mm) GN2/3 ONE -THIRD SIZE PAN 12" x 6" x 2-1/2" (325mm x 176mm x 65mm) GN1/3 — 48 MODELS: Up to 3 Two-Thirds Size Pans with 6 One-Third Size Pans per display case — 72 MODELS: Up to 5 Two-Thirds Size Pans with 10 One-Third Size Pans per display case — 96 MODELS: Up to
O P E R AT I N G I N S T R U C T I O N S 1002585 1000544 1002619 Part No.
O P E R AT I N G I N S T R U C T I O N S GENERAL HOLDING GUIDELINES Chefs, cooks and other specialized food service personnel employ varied methods of cooking. Proper holding temperatures for a specific food product must be based on the moisture content of the product, product density, volume, and proper serving temperatures. Safe holding temperatures must also be correlated with palatability in determining the length of holding time for a specific product.
CARE AND CLEANING CLEANING AND PREVENTIVE MAINTENANCE PROTECTING STAINLESS STEEL SURFACES CLEANING AGENTS It is important to guard against corrosion in the care of stainless steel surfaces. Harsh, corrosive, or inappropriate chemicals can completely destroy the protective surface layer of stainless steel. Abrasive pads, steel wool, or metal implements will abrade surfaces causing damage to this protective coating and will eventually result in areas of corrosion.
CARE AND CLEANING EQUIPMENT CARE Under normal circumstances, this appliance should provide you with long and trouble free service. There is no preventative maintenance required, however, the following Equipment Care Guide will maximize the potential life and trouble free operation of this appliance. The cleanliness and appearance of this equipment will contribute considerably to operating efficiency and savory, appetizing food. Good equipment that is kept clean works better and lasts longer.
S A N I TAT I O N Food flavor and aroma are usually so closely related that it is difficult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food flavor. Cleanliness, top operating efficiency, and appearance of equipment contribute considerably to savory, appetizing foods. Good equipment that is kept clean, works better and lasts longer. Most food imparts its own particular aroma and many foods also absorb existing odors.
SERVICE HN2 Series - Service Views Control Panel Access Switch Thermostat SW-33896 TT-3498 Fuses Switch Thermostat FU-3775 SW-33896 TT-3498 Cutting Board Bracket Indicator Light LI-3027 BT-2342 Indicator Light LI-3027 Control Panel for Model HN2-48 Cable Wrap: Access by removal of bottom panel CB-3045 #894 • HN2 Series Operation & Care Manual • 16
SERVICE Cable Replacement Kits HN2-48 Series Cable Replacement Kit Cable Heating Service Kit No. 4880 includes: CB-3045 Cable Heating Element . . . . . . . . . . . .134 feet CR-3226 Ring Connector . . . . . . . . . . . . . . . . . . . . . . . .4 IN-3488 Insulation Corner . . . . . . . . . . . . . . . . . .1 foot BU-3105 Shoulder Bushing . . . . . . . . . . . . . . . . . . . . . .4 BU-3106 Cup Bushing . . . . . . . . . . . . . . . . . . . . . . . . . .4 SL-3063 Insulating Sleeve . . . . . . . . .
1. BULBS BULBS, 230V RECEPTACLE, BULB RECEPTACLE, BULB, 230V 48 Y 2S 2S N N H H H S- SY 48 2N 2N H Alto-Shaam Part No. Part Description 48 /P 48 /P HN2-48 Series LP-33592 LP-3384 RP-3952 RP-3955 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 2. BUMPER BUMPER END CAP BUMPER TRACK BM-24082 BM-24083 11088 1 2 1 1 2 1 1 2 1 1 2 1 3.
R L 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 2. BUMPER BUMPER END CAP BUMPER TRACK BM-24082 BM-24083 11089 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 3. CLAMP, GLASS CM-26920 1 1 1 1 1 1 1 1 1001252 1 1 1 1 1 1 1 1 CD-3557 CD-33490 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6.
14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 2. BUMPER BUMPER END CAP BUMPER TRACK BM-24082 BM-24083 11090 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 3.
SERVICE Lower Door Track HN2SYS-48 - TK-26751 HN2SYS-72 - TK-26753 HN2SYS-96 - TK-26755 Glass Clamp Door Assembly RIGHT-HAND DR-25423 MIDDLE DR-25424 LEFT-HAND DR-25422 HN2SYS-48 - CM-26919 HN2SYS-72 - CM-26920 HN2SYS-96 - CM-26921 End Glass LEFT OR RIGHT GL-26947 End Panel 1005367 Front Glass Bumper BM-24082 Handle Bumper Track HN2SYS-48 - 11088 HN2SYS-72 - 11089 HN2SYS-96 - 11090 HN2SYS-48 - 1001656 HN2SYS-72 - 1001657 HN2SYS-96 - 1001658 HN2SYS-48 - GL-26910 HN2SYS-72 - GL-26911 HN2SYS-96 - GL
#894 • HN2 Series Operation & Care Manual • 22
#894 • HN2 Series Operation & Care Manual • 23
#894 • HN2 Series Operation & Care Manual • 24
#894 • HN2 Series Operation & Care Manual • 25
#894 • HN2 Series Operation & Care Manual • 26
#894 • HN2 Series Operation & Care Manual • 27
T R A N S P O RTAT I O N DAMAGE and CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be established on the part of the shipper. 1. 2.
