RMX508DFX QUICKSTART GUIDE ENGLISH
BOX CONTENTS y y y y RMX508DFX Power cable Quickstart Guide Safety Instructions & Warranty Information booklet CONNECTION DIAGRAM -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD POWER HI 12kHz HI 12kHz -15 HI 12kHz -15 HI 12kHz -15 HI 12kHz HI 12kHz HI 12kHz -15 -15 -15 HI 12kHz -15 -15 +10 MID 2.5kHz MID 2.5kHz -15 MID 2.5kHz -15 LOW 80Hz -15 -15 -15 AUX SEND +10dB - +10dB - 2 FX POST POST -15 -15 AUX SEND PRE MID 2.
FRONT PANEL -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD -20dB PAD POWER HI 12kHz HI 12kHz -15 HI 12kHz -15 HI 12kHz -15 HI 12kHz -15 -15 HI 12kHz HI 12kHz HI 12kHz -15 -15 -15 +10 MID 2.5kHz MID 2.5kHz MID 2.
MASTER SECTION 11. 12. 13. 14. 15. 16. 17. 18. STEREO GRAPHIC EQ: There are two graphic EQs each with 9 adjustable bands; one is for the MAIN mix and the other is for the MONITOR mix. With the faders you can boost or cut the selected frequency by +/-15 dB at the indicated frequencies. When all faders are at the center position, the equalizer is disabled. FEEDBACK TERMINATOR Button (MONITOR mix)- This button activates the feedback detection in the monitor signal path.
DSP (DIGITAL SIGNAL PROCESSOR) 28. 29. 30. 31. 32. 33. 34. EFFECTS SELECTOR – Selects the effect that the mixer's internal effects processor will apply to the various channels. Each channel can send different levels of audio to the processor by adjusting their Aux 2/FX Post knobs. FX MUTE – Press this button to mute/unmute the effects. VARIATIONS SELECTOR – Selects the amount of the effect applied to the various channels.
EFFECTS TO HEAR THE EFFECTS ON A CHANNEL: Use the Effects Selector to choose one of the effects below, adjust the parameter with the Variations Selector, then turn up the Aux 2/FX Post knob for that channel. # PRESET DESCRIPTION PARAMETER RANGE 0.8~1.1s 0~79ms 1 VOCAL 1 Reverb, simulating a room with a small delay time. Decay time Pre-delay 2 VOCAL 2 Reverb, simulating a small space with a small delay time. Decay time Pre-delay 0.8~2.
AUDIO LINE/MIC CONNECTIONS You can connect unbalanced equipment to balanced inputs and outputs. Simply follow these schematics. ! Caution: Do not connect the rear panel speaker level ¼” outputs to anything other than a passive loudspeaker. Connecting this output to a line line/Mic level input may damage your equipment.
TECHNICAL SPECIFICATIONS MONO INPUT CHANNELS • Microphone input: Electronically balanced, discrete input configuration • Frequency response: 10Hz to 55kHz, +/–3dB • Distortion: (THD & N) 0.006% at +4dBu, 1kHz • Gain: 50dB (MIC) • SNR: (Signal to Noise Ratio) >90dB • Line input: Electronically balanced • Frequency response: 10Hz to 55kHz, +/–3dB • Distortion: (THD & N) 0.
www.altoprofessional.com MANUAL VERSION 1.
