Installation Guide

ManualsBrandsAltronix ManualsAccess Control Power productsPower Supply/Charger w/Access Power Controller

Access Power Controllers

with Power Supplies

Installation Guide for models:

eFlow4NA8 eFlow6NA8

- 4 amp @ 12VDC or 24VDC - 6 amp @ 12VDC or 24VDC

- Eight (8) Fused Outputs - Eight (8) Fused Outputs

eFlow102NA8 eFlow104NA8

- 10 amp @ 12VDC - 10 amp @ 24VDC

- Eight (8) Fused Outputs - Eight (8) Fused Outputs

ULC-S319 - Electronic Access Control Systems will be invalidated through the use of any add-on, expansion,

memory or other module manufactured by the manufacturer or other manufacturers.

For a red enclosure add an “R” suffix to the part # e.g. eFlow4NA8R

Rev. eACM052313 More than just power.™

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Altronix Corp.

140 58th St. Brooklyn, NY

Summary of content (12 pages)

PAGE 1
Access Power Controllers with Power Supplies Installation Guide for models: eFlow4NA8 eFlow6NA8 eFlow102NA8 eFlow104NA8 - 4 amp @ 12VDC or 24VDC - Eight (8) Fused Outputs - 6 amp @ 12VDC or 24VDC - Eight (8) Fused Outputs - 10 amp @ 12VDC - Eight (8) Fused Outputs - 10 amp @ 24VDC - Eight (8) Fused Outputs ULC-S319 - Electronic Access Control Systems will be invalidated through the use of any add-on, expansion, memory or other module manufactured by the manufacturer or other manufacturers.
PAGE 2
Overview: These units distribute and switch power to access control systems and accessories. They convert a 120VAC 60Hz input into eight (8) independently controlled 12VDC or 24VDC fuse protected outputs. These power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc.
PAGE 3
• • • • • Overvoltage Protection. Built-in charger for sealed lead acid or gel type batteries. Maximum charge current 1.54 amp. Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption. Supervised Fire Alarm disconnect (latching or non-latching) 10K EOL resistor. Operates on a normally open (NO) or normally closed (NC) trigger. • AC fail supervision (form “C” contacts). • Battery fail & presence supervision (form “C” contacts).
PAGE 4
(b) Open Collector Sink inputs: Connect the access control panel open collector sink positive (+) to terminals marked [IN] and the negative (-) to terminals marked [GND]. 8. ACM8 Fire Alarm Interface options (Figs. 5-10, pg. 9): A normally closed [NC] or normally open [NO] input trigger from a fire alarm control panel or a polarity reversal input from an FACP signaling circuit will affect selected outputs.
PAGE 5
Power Supply Board LED Diagnostics: Red (DC) ON ON OFF OFF Green (AC/AC1) ON OFF ON OFF Power Supply Status Normal operating condition. Loss of AC. Stand-by battery supplying power. No DC output. Loss of AC. Discharged or no stand-by battery. No DC output. Access Power Controller LED Diagnostics: LED LED 1- LED 8 (Red) Trg (Green) ON Output relay(s) energized. FACP input triggered (alarm condition). OFF Output relay(s) de-energized. FACP normal (non-alarm condition).
PAGE 6
Power Supply Board Stand-by Battery Specifications: Battery 7AH 12AH 40AH 65AH eFlow4NA8 30 Mins./4 amp* 35 Mins./4 amp* Over 4 Hours/4 amp* Over 4 Hours/4 amp* eFlow6NA8 10 Mins./6 amp 30 Mins./6 amp* Over 4 Hours/6 amp* Over 4 Hours/6 amp* eFlow102NA8 5 Mins./10 amp 30 Mins./10 amp* Over 2 Hours/10 amp* Over 4 Hours/10 amp* eFlow104NA8 5 Mins./10 amp 30 Mins./10 amp* Over 2 Hours/10 amp* Over 4 Hours/10 amp* *Only these configurations can be utilized in ULC-S319 installations.
PAGE 7
Fig. 3 Fig. 3a --- DC + Green Lead (ground) Enclosure Door Battery & AC Supervision Circuit (Power-limited) C --- BAT + (eFlow4NA8 power-limited) (eFlow6NA8, eFlow102NA8, eFlow104NA8 non power-limited) SHUTDOWN AC AC DELAY AC1 DC NO C NO NC 2 hr. 1 min.
PAGE 8
NEC Power-Limited Wiring Requirements for eFlowNA8 Models: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limitedcircuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below.
PAGE 9
FACP Hook-Up Diagrams: Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): CUT JUMPER CUT JUMPERS J1 AND J2 TRG J2 J1 ISOLATED POWER INPUT 12 OR 24 VAC OR VDC (ACM8 POWER) Fig. 7 Normally Open - Non-Latching FACP Fig. 8 trigger input: -- FROM FACP OUTPUT + CIRCUIT Normally Open FACP Latching trigger input with reset: (This output has not been evaluated by UL) INTERFACE TRG N.O. TRIGGER INPUT N.O. TRIGGER INPUT N.C.
PAGE 10
Notes - 10 - eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series
PAGE 11
Notes eFlow4NA8, eFlow6NA8, eFlow102NA8, eFlow104NA8 series - 11 -
PAGE 12
Enclosure Dimensions (BC400) (approximate H x W x D): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.75” (44.45mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.5” (38.1mm) 1.125” (28.575mm) 15.5” (393.7mm) 2.0” (50.8mm) 2.0” (50.8mm) 5.0” (127.0mm) 2.5” (63.5mm) 1.1” (27.94mm) 1.75” (44.