Installation

- 2 - HubSat4Di
Overview:
Altronix HubSat4Di Passive UTP Transceiver Hub w/Integral Isolated Camera Power transmits UTP video, RS422/RS485
data and power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount enclo-
sure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ
cameras when utilizing Altronix HubWayAv or HubWayDv Video Balun/Combiners. In addition, the unit features individ-
ually selectable 24VAC or 28VAC electronically isolated fuse protected outputs with surge suppression. Optionally, the
HubSat4Di can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher
structured cable back to the HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition,
the HubSat4Di provides power to these cameras locally to eliminate the possibility of voltage drop associated with long
cable runs.
Input:
• 115VAC 50/60Hz, 1.25 amp.
• Primary in-line fuse is rated @ 3.5A/250V.
Video:
• Four (4) channels of quality video over twisted pair
up to a distance of 750 ft. per channel.
• Four (4) 75 ohm video outputs.
Data:
• RS422/RS485 data input.
Power:
• Individually selectable 24VAC or 28VAC power
outputs with OFF position.
• Unit provides up to 1 amp max. per channel not to
exceed a total of 4 amp maximum current.
Power (cont.):
• Individual electronically isolated outputs.
• PTC protected outputs are rated @ 1 amp per channel.
• Surge suppression.
Visual Indicators:
• Four (4) power LED indicators.
Enclosure Dimensions:
8.5”H x 7.5”W x 3.5”D
Optional Accessories:
• Video Balun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
Specifications:
Additional Models:
HubSat42Di
• HubSat4Di w/four (4) HubWayAv Video Balun/
Combiners for 24VAC Cameras.
HubSat43Di
• HubSat4Di w/four (4) HubWayDv Video Balun/
Combiners for 12VDC Cameras.
Installation Instructions:
HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power.
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install tw
o upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 8).
Secure green wire lead to earth ground.
2.
Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).
3.
Connect 115VAC 50/60Hz to the black and white flying leads of open frame transformer. Secure ground
wire (Green) to earth ground (Fig. 5, pg
. 7). The power LEDs (Green) for Channels 1-4 of the HubSat4Di
will illuminate when AC power is present (Fig. 1e, pg. 4)
4. Select 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4Di (Fig. 4, pg. 6) with the corresponding
output v
oltage switches. Select OFF position when servicing or installing individual cameras (Fig. 1d, pg. 4).
5.
Connect the BNC video outputs marked [Video 1-4] on HubSat4Di to the corresponding video inputs on the
head end equipment (DVR) (Fig. 1a, pg. 4).
6. Connect terminals marked [+ Data --- ] on HubSat4Di (polarity must be obser
ved) to the RS422/RS485 output of the
head end equipment (DVR) (Fig. 1f, pg. 4). When using fixed cameras disregard this step.
7.
Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]
on HubSat4Di (Fig
. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
• For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (Figs. 2a, 2b, pg. 6).
• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).
•
For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 6).