Video • Data • Power Passive UTP Transceiver Hub with Integral Camera Power Installation Guide Models Include: HubSat8D - Eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Power HubSat82D - Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayAv Video Balun/Combiners HubSat83D - Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayDv Video Balun/Combiners Rev. 112508 More than just power.
Overview: Altronix HubSat8D Passive UTP Transceiver Hub w/Integral Camera Power transmits UTP video, RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a wall mount enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners.
7. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1] on Circuit Board A (Fig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1. • For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (Figs. 2a, 2b, pg. 6). • For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).
2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1] on Circuit Board A (Fig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1. • For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (Figs. 2a, 2b, pg. 6). • For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).
10. The power LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 4). Note: If any of the power LEDs are not illuminated the cause may be due to the following: a. AC mains fail. b. Illuminated master power disconnect circuit breaker is tripped. Primary c. One or both primary in-line fuse(s) are blown. In-line Fuse Note: Replace fuse with same type and rating: Primary in-line fuses are rated @ 3.5A/250V (Fig. 4b, pg. 6). d.
Fig. 2 - HubWayAv and HubWayDv/Dvi Video Balun/Combiners Fig. 2c Fig. 2a VIDEO VIDEO HubWayAv HubWayDv VIDEO BALUN/COMBINER CAT5 VIDEO BALUN/COMBINER AC + DATA-- POWER CAT5 Wire Connectors RJ45 Jack * Also Available as: HubWayDvi Video Balun/ Combiner for non-isolated 12VDC cameras + DATA-- -- 12VDC+ Wire Connectors RJ45 Jack Fig. 2b Fig.
Typical Application Drawing HubSat8D Passive UTP Transceiver Hub with Integral Camera Power: Fig.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.