Video • Data • Power Passive UTP Transceiver Hub with Integral Camera Isolated Power Installation Guide Models Include: HubSat8Di - Eight (8) Channel Passive UTP Transceiver Hub with Integral Camera Isolated Power HubSat82Di - Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayAv Video Balun/Combiners HubSat83Di - Eight (8) Channel Passive UTP Transceiver includes eight (8) HubWayDv Video Balun/Combiners Rev. 032910 More than just power.
Overview: Altronix HubSat8Di Passive UTP Transceiver Hub w/Integral Camera Isolated Power transmits UTP video, RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 camera channels in a wall mount enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv or HubWayDv Video Balun/Combiners.
7. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1] on Circuit Board A (Fig. 1i, pg. 5). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1. • For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e, pg. 6). • For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).
The total cable distance must not exceed 750 ft. for video transmission between the HubSat8Di and each camera. Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B. 3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 3a, pg. 6). Power LEDs (Green) of the HubSat8Di will illuminate when AC power is present (Fig. 1e, pg.
Fig. 1 - HubSat Circuit Board A / HubSat Circuit Board B 1c 1c 28VAC 28VAC OFF AUX2 OFF AUX1 24VAC 24VAC VIDEO1 VIDEO2 AUX3 1d AUX4 28VAC OFF 28VAC OFF 1b 24VAC 24VAC VIDEO3 1e VIDEO4 + DATA - 1a 1i PVD1 PVD2 DATA 1-4 VIDEO 1-4 1h 1g 1a - BNC Connector: Video in from remote camera video out to DVR. 1b - Output PTCs: Protects each output. 1c - Power Terminals: 24VAC/28VAC power outputs. 1d - Output Voltage Switches: Selects 24VAC/28VAC/ OFF for each output.
Fig. 2 - HubWayAv and HubWayDv Video Balun/Combiners Fig. 2c Fig. 2a VIDEO VIDEO HubWayAv HubWayDv VIDEO BALUN/COMBINER CAT5 RJ45 Jack VIDEO BALUN/COMBINER AC + DATA-- POWER CAT5 Wire Connectors + DATA-- -- 12VDC+ Wire Connectors RJ45 Jack Fig. 2b Fig. 2d Green Power LED To BNC Connector of Camera Structured Cable from HubSat8Di Red Power LED To BNC Connector of Camera AC Power to Camera Structured Cable from HubSat8Di + 12VDC Power -- to Camera -- Data to + Camera Fig.
Typical Application Drawing HubSat8Di Passive UTP Transceiver Hub with Integral Camera Power: Fig.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
