HubWayLD8CD_16CD Installation

ManualsBrandsAltronix ManualsData UTP8 Channel Active UTP Transceiver Hub, 115VAC

Rev. 030408

Active UTP Transceiver Hubs

with Integral Camera Power

Installation Guide

Models Include:

HubWayLD8CD HubWayLD16CD

- UL Listed eight (8) Channel Active UTP - UL Listed sixteen (16) Channel Active UTP

Transceiver Hub with Integral Camera Power Transceiver Hub with Integral Camera Power

HubWayLD82CD HubWayLD162CD

- UL Listed eight (8) Channel Active UTP - UL Listed sixteen (16) Channel Active UTP

Transceiver Hub with Integral Camera Power Transceiver Hub with Integral Camera Power

- Includes eight (8) UL Listed Accessory - Includes sixteen (16) UL Listed Accessory

HubWayAv Video Balun/Combiners HubWayAv Video Balun/Combiners

HubWayLD83CD HubWayLD163CD

- UL Listed eight (8) Channel Active UTP - UL Listed sixteen (16) Channel Active UTP

Transceiver Hub with Integral Camera Power Transceiver Hub with Integral Camera Power

- Includes eight (8) UL Listed Accessory - Includes sixteen (16) UL Listed Accessory

HubWayDv Video Balun/Combiners HubWayDv Video Balun/Combiners

More than just power.

Video • Data • Power

Summary of content (8 pages)

PAGE 1
Video • Data • Power Active UTP Transceiver Hubs with Integral Camera Power Installation Guide Models Include: HubWayLD8CD HubWayLD16CD - UL Listed eight (8) Channel Active UTP Transceiver Hub with Integral Camera Power - UL Listed sixteen (16) Channel Active UTP Transceiver Hub with Integral Camera Power HubWayLD82CD HubWayLD162CD - UL Listed eight (8) Channel Active UTP Transceiver Hub with Integral Camera Power - Includes eight (8) UL Listed Accessory HubWayAv Video Balun/Combiners - UL Listed s
PAGE 2
Overview: Altronix HubWayLD8CD/LD16CD Active UTP Transceiver Hubs w/Integral Camera Power transmits UTP video, RS422/RS485 data and power over a single CAT-5 or higher structured cable. Units provides 8 or 16 camera channels in a space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is up to 3000 ft. max. per channel.
PAGE 3
. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7). 4. Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWayLD8CD/LD16CD unit (Fig. 1j, pg. 4). Insert the plug end of the line cord into a grounded 115VAC receptacle. 5. Set voltage output selector switch for each camera channel for 24VAC or 28VAC (Fig. 1d, pg. 4). 6.
PAGE 4
-4- PICTURE GAIN 16 1 14 2 3 13 4 6 10 7 9 1g - Picture: Adjusts video quality. GAIN 8 CH 5-8 28VAC OFF 24VAC 1h - Gain: Regulates the output video and sync levels. GAIN PICTURE GAIN PICTURE 5 11 GAIN PICTURE + DATA 1-8 CH 1-4 12 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE 15 1f - BNC Connector: Video outputs to head end equipment (DVR). Rear OFF RESET Front 1c - LED(s) 1-16: Power indicators.
PAGE 5
Po we rL ED Ty pe Ca m era Ou t to put V ca o m lta era ge Altronix Model Number In p fro ut V m o un H ltag it ub e W ay HubWayAv, HubWayDv and HubWayDvi Video Balun/Combiners: HubWayAv *24VAC/28VAC *24VAC/28VAC 24VAC cameras Green HubWayDv *24VAC/28VAC 12VDC 12VDC cameras Red HubWayDvi *24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red *Based on camera load and structured cable length. Fig. 2 Fig. 2c Fig.
PAGE 6
Typical Applications: Fig. 4 Head End Equipment (DVR) RS485 Monitor Video Data Rear 8 7 PICTURE GAIN 1 2 3 4 CH 1-4 5 6 7 + DATA 1-8 8 6 5 4 3 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE 2 1 GAIN PICTURE GAIN PICTURE AC POWER GAIN CH 5-8 28VAC OFF 24VAC Front CAT-5 Video Power Video Power Four (4) Video signals on a single CAT-5 Video Data Power Data (CAT-5) CAT-5 CAT-5 Max. video 3000 ft.
PAGE 7
1U EIA 19” Rack Mount Chassis Mechanical Drawing & Dimensions: 1.625”H x 19.125”W x 8.5”D REAR 1.625" 16 PICTURE GAIN 14 15 13 12 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE 11 GAIN PICTURE 10 9 GAIN PICTURE GAIN PICTURE 8 GAIN PICTURE GAIN 7 6 5 4 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE 3 GAIN PICTURE 2 1 GAIN PICTURE GAIN PICTURE AC POWER GAIN TOP & BOTTOM 17.625" 8.
PAGE 8
Mounting Options: Rack Mount Installation 1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 6a). 2- Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 6b). 3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 6c). Fig. 6 Fig. 6b Fig. 6a Fig.