Installation Instructions

ManualsBrandsAltronix Manualselectrical equipment & suppliesMAXIMAL75D

Series

Access Power Controllers

Installation Guide

Models Include:

Rev. DCB102512

Maximal11D

- Power Supply 1:

12VDC @ 3.5A or 24VDC @ 2.7A.

- Power Supply 2:

12VDC @ 3.5A or 24VDC @ 2.7A.

- Sixteen (16) PTC protected

Class 2 Rated power-limited outputs.

Maximal33D

- Power Supply 1:

12VDC @ 5.5A or 24VDC @ 5.7A.

- Power Supply 2:

12VDC @ 5.5A or 24VDC @ 5.7A.

- Sixteen (16) PTC protected

Class 2 Rated power-limited outputs.

Maximal55D

- Power Supply 1: 12VDC @ 9.5A.

- Power Supply 2: 12VDC @ 9.5A.

- Sixteen (16) PTC protected

Class 2 Rated power-limited outputs.

Maximal77D

- Power Supply 1: 24VDC @ 9.7A.

- Power Supply 2: 24VDC @ 9.7A.

- Sixteen (16) PTC protected

Class 2 Rated power-limited outputs.

Maximal75D

- Power Supply 1: 12VDC @ 9.5A.

- Power Supply 2: 24VDC @ 9.7A.

- Sixteen (16) PTC protected

Class 2 Rated power-limited outputs.

More than just power.

Altronix Corp.

140 58th St. Brooklyn, NY

Summary of content (20 pages)

PAGE 1
Access Power Controllers Series Installation Guide Models Include: Maximal11D Power Supply 1: 12VDC @ 3.5A or 24VDC @ 2.7A. Power Supply 2: 12VDC @ 3.5A or 24VDC @ 2.7A. Sixteen (16) PTC protected Class 2 Rated power-limited outputs. Maximal33D Power Supply 1: 12VDC @ 5.5A or 24VDC @ 5.7A. Power Supply 2: 12VDC @ 5.5A or 24VDC @ 5.7A. Sixteen (16) PTC protected Class 2 Rated power-limited outputs. Maximal55D Power Supply 1: 12VDC @ 9.5A. Power Supply 2: 12VDC @ 9.5A.
PAGE 2
Table of Contents: MaximalD Series Overview.............................................................................................. 3 MaximalD Series Configuration Chart.............................................................................. 3 MaximalD Series Features............................................................................................. 3-4 MaximalD Installation Instructions................................................................................ 4-5 Maintenance....
PAGE 3
MaximalD Series Overview: Maximal Access Power/Controllers distribute and switch power to access control systems and accessories. They convert a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC or 24VDC Class 2 Rated PTC protected powerlimited outputs. The outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Keypad, Push Button, REX PIR, etc.
PAGE 4
• ACM8CB maximum current is 2A per output. • Red LEDs on ACM8CB board indicate individual outputs are triggered (relays energized). • Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the sixteen (16) outputs. Fire Alarm disconnect input trigger options: a) Normally open (NO) or normally closed (NC) dry trigger input. b) Polarity reversal input from FACP signaling circuit. • Green LED on ACM8CB board indicates FACP disconnect is triggered.
PAGE 5
. Output options (Fig. 2, pg. 9): The unit will provide either sixteen (16) switched power outputs, sixteen (16) dry form “C” outputs, or any combination of both switched power and form “C” outputs. (a) Fail-Safe Switched Power outputs: For Fail-Safe operation connect the positive (+) input of the access control devices to terminal marked [NC]. Connect the negative (-) input of the access control devices to terminal marked [COM].
PAGE 6
Maintenance: Unit should be tested at least once a year for the proper operation as follows: FACP Supervision: To insure proper connection and operation of the Fire Alarm disconnect hookup. Please follow the appropriate procedure below: Normally Open Input: Placing a short between terminals marked [T] and [+ INP] will trigger the Fire Alarm Disconnect. Remove the short to reset. Normally Closed Input: Remove the wire from terminal marked [INP -- ] will trigger the Fire Alarm Disconnect.
PAGE 7
Power Supply Board Terminal Identification: Terminal Legend L, N Function/Description Connect 115VAC 60Hz to these terminals: L to hot, N to neutral. + DC - Maximal11D - 12VDC @ 3.5A or 24VDC @ 2.7A to ACM8CB boards (power-limited). Maximal33D - 12VDC @ 5.5A or 24VDC @ 5.7A to ACM8CB boards (power-limited). Maximal55D - 12VDC @ 9.5A to ACM8CB boards (power-limited). Maximal77D - 24VDC @ 9.7A to ACM8CB boards (power-limited). Maximal75D - one (1) power supply which is 12VDC @ 9.
PAGE 8
Power Supply Board Stand-by Battery Specifications: Altronix Model Maximal11D Maximal33D Power Supply Board Battery 20 Min. of Backup 4 Hr. of Backup 24 Hr. of Backup AL400ULXB2 12VDC/40AH* N/A 3.5A 0.5A (Refer to Fig. 1a, pg. 9 for Switch [SW1] location and position) 24VDC/40AH* N/A 2.7A 0.7A AL600ULXB 12VDC/40AH* N/A 5.5A 5.5A 24VDC/40AH* N/A 5.5A 0.7A AL1012ULXB 12VDC/12AH 9.0A Battery capacity for emergency stand-by at least 20 mins. N/A (Refer to Fig. 1a, pg.
PAGE 9
Power Supply Board Output Voltage Settings: Fig. 1 Fig. 1a SW1 + DC --- ON ON OFF - 24V ON - 12V OFF - 24V ON - 12V Maximal11D/Maximal33D Power Supply Board Fig. 2 Access Power Controller Typical Application Diagram (for each ACM8CB): Fig. 2a Intact = Dry Input Cut = Wet Input Normally Open (N.O.) Door Releasing Device FACP Keypad Access Control Panel TRG (Fire Alarm Control Panel) C NO Fig.
PAGE 10
Fig.
PAGE 11
Fig.
PAGE 12
Fig.
PAGE 13
NEC Power-Limited Wiring Requirements for Maximal11D: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 14
NEC Power-Limited Wiring Requirements for Maximal33D and Maximal55D: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below.
PAGE 15
NEC Power-Limited Wiring Requirements for Maximal77D: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 16
NEC Power-Limited Wiring Requirements for Maximal75D: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 17
FACP/Optional Power Supply Hook-up Diagrams: Fig. 10 Optional hook-up using two (2) isolated power supply inputs (Only applicable on Maximal11D): Fig. 11 Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): CUT JUMPER CUT JUMPERS J1 AND J2 J1 ISOLATED POWER INPUT 12 OR 24 VAC OR VDC (ACM8 POWER) FACP OUTPUT EOL INTERFACE J2 TRG -- FROM FACP OUTPUT + CIRCUIT NO C NC FACP ISOLATED POWER INPUT 12 OR 24 VAC OR VDC (LOCK POWER) Fig.
PAGE 18
Enclosure Dimensions (H x W x D approximate): 26” x 19” x 6.25” (660.4mm x 482.6mm x 158.75mm) 19” (482.6mm) 2” (50.8mm) 4” (101.6mm) 7” (177.8mm) 4” (101.6mm) 2” (50.8mm) 6.25” (158.75mm) TOP 1.25” (31.75mm) 0.85” (21.59mm) 19” (482.6mm) 8.9” (226.06mm) 1.25” (31.75mm) 0.85” (21.59mm) 8.4” (213.36mm) 1.5” (38.1mm) 1.5” (38.1mm) 1.5” (38.1mm) 5” (127mm) 8.5” (215.9mm) 7” (177.8mm) 7.5” (190.5mm) 7.5” (190.5mm) 26” (660.4mm) 8.5” (215.9mm) 26” (660.4mm) 26” (660.
PAGE 19
Notes: Maximal11D/Maximal33D/Maximal55D/Maximal77D/Maximal75D Access Power Controllers (PTC) - 19 -
PAGE 20
Notes: Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail: info@altronix.com. Lifetime Warranty, Made in U.S.A.