Installation Instructions

ManualsBrandsAltronix ManualsComputers & Accessories2 Power Supply/Chargers - 12 or 24VDC

Maximal11FE

- Power Supply 1: 12VDC or 24VDC @ 4 amp.

- Power Supply 2: 12VDC or 24VDC @ 4 amp.

Maximal13FE

- Power Supply 1: 12VDC or 24VDC @ 4 amp.

- Power Supply 2: 12VDC or 24VDC @ 6 amp.

Maximal33FE

- Power Supply 1: 12VDC or 24VDC @ 6 amp.

- Power Supply 2: 12VDC or 24VDC @ 6 amp.

Maximal35FE

- Power Supply 1: 12VDC or 24VDC @ 6 amp.

- Power Supply 2: 12VDC @ 10 amp.

Maximal37FE

- Power Supply 1: 12VDC or 24VDC @ 6 amp.

- Power Supply 2: 24VDC @ 10 amp.

Maximal55FE

- Power Supply 1: 12VDC @ 10 amp.

- Power Supply 2: 12VDC @ 10 amp.

Maximal75FE

- Power Supply 1: 24VDC @ 10 amp.

- Power Supply 2: 12VDC @ 10 amp.

Maximal77FE

- Power Supply 1: 24VDC @ 10 amp.

- Power Supply 2: 24VDC @ 10 amp.

Rev. MFE051313

Series

Expandable Power Systems

Installation Guide

Models Include:

Altronix Corp.

140 58th St. Brooklyn, NY

More than just power.

Summary of content (12 pages)

PAGE 1
Series Expandable Power Systems Installation Guide Models Include: Maximal11FE Maximal37FE Maximal13FE Maximal55FE Maximal33FE Maximal75FE Maximal35FE Maximal77FE - Power Supply 1: 12VDC or 24VDC @ 4 amp. - Power Supply 2: 12VDC or 24VDC @ 4 amp. - Power Supply 1: 12VDC or 24VDC @ 4 amp. - Power Supply 2: 12VDC or 24VDC @ 6 amp. - Power Supply 1: 12VDC or 24VDC @ 6 amp. - Power Supply 2: 12VDC or 24VDC @ 6 amp. - Power Supply 1: 12VDC or 24VDC @ 6 amp. - Power Supply 2: 12VDC @ 10 amp.
PAGE 2
MaximalFE Overview: Maximal Expandable Power Systems provide system designers and installers with optimum power choices and the highest levels of versatility. They provide 12VDC, 24VDC, or 12VDC and 24VDC simultaneously via two (2) single output power supply/chargers. Includes AC fail, low battery, and battery presence monitoring. Enclosure facilitates up to four (4) 12VDC/12AH batteries. All interconnecting equipment must be UL Listed. Input: • 120VAC, 60Hz.
PAGE 3
Maximal11FE Maximal13FE Maximal33FE Maximal35FE Maximal37FE Maximal55FE eFlow4NB eFlow4NB 10.1- ---------- 10.05- ---------- 10.1- ---------- 10.05- ---------13.2 13.2 13.2 13.2 10.1- ---------- 10.05- ---------- ---------- 20.28- ---------- 20.2- 4A + 4A 13.2 13.2 26.4 26.4 20.2820.220.2820.2---------- 26.4 ---------- 26.4 ---------- 26.4 ---------- 26.4 eFlow4NB eFlow6NB 10.1- ---------- 10.05- ---------- 10.0- ---------- 10.03- ---------13.2 13.2 13.2 13.2 10.1- ---------- 10.
PAGE 4
MaximalFE Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, the Canadian Electric Code, Part I, Part II, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. Power Supply Board Terminal Identification (pg. 5) Power Supply Stand-by Battery Specifications (pg. 5) Power Supply Board LED Diagnostics (pg. 6) Power Supply Board Output Voltage Settings (pg. 6) 1. Mount unit in desired location.
PAGE 5
Power Supply Board Terminal Identification: Terminal Legend L, G, N + DC – Trigger EOL Supervised NO, GND RESET + AUX – AC Fail NC, C, NO Bat Fail NC, C, NO – BAT + Function/Description Connect 120VAC 60Hz to these terminals: L to hot, N to neutral. Do not use the [G] terminal Refer to MaximalFE Series Configuration Chart, pg. 3. Fire Alarm Interface trigger input from a short or FACP. Trigger inputs can be normally open, normally closed from an FACP output circuit (power-limited input).
PAGE 6
Power Supply Board LED Diagnostics: Green (DC) ON ON OFF OFF Green (AC/AC1) ON OFF ON OFF Power Supply Status Normal operating condition. Loss of AC. Stand-by battery supplying power. No DC output. Loss of AC. Discharged or no stand-by battery. No DC output. Power Supply Board Output Voltage Settings: Fig. 1 - eFlow4NB / eFlow6NB Power Supply Board --- DC + ON ON OFF - 24V ON - 12V Fig.
PAGE 7
Fig. 2 --- BAT + --- DC + OFF - 24V ON - 12V ON Tamper Switch AC1 5A 250V L G Line N AC FAIL BAT FAIL Fig. 2a AC DELAY SHUTDOWN O N NC C NO NC C NO AC DC 1 min. 2 hr. enable disable TRIGGER EOL SUPERVISED NO GND RESET + AUX – Neutral Enclosure Edge of Enclosure --- BAT + --- DC + ON OFF - 24V ON - 12V Sentrol model # 3012 Tamper Switch or equivalent (Not Included) AC1 5A 250V L 120VAC Input 60 Hz. Line G N AC FAIL BAT FAIL to Access Control Panel or U.L.
PAGE 8
NEC Power-Limited Wiring Requirements: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 9
Enclosure Dimensions (H x W x D approximate): 26” x 19” x 6.25” (660.4mm x 482.6mm x 158.75mm) 19” (482.6mm) 2” (50.8mm) 4” (101.6mm) 7” (177.8mm) 4” (101.6mm) 2” (50.8mm) 6.25” (158.75mm) TOP 1.25” (31.75mm) 0.85” (21.59mm) 19” (482.6mm) 8.9” (226.06mm) 1.25” (31.75mm) 0.85” (21.59mm) 8.4” (213.36mm) 1.5” (38.1mm) 1.5” (38.1mm) 1.5” (38.1mm) 5” (127mm) 8.5” (215.9mm) 7” (177.8mm) 7.5” (190.5mm) 7.5” (190.5mm) 26” (660.4mm) 8.5” (215.9mm) 26” (660.4mm) 26” (660.
PAGE 10
Notes: Maximal Expandable Power Systems - 10 -
PAGE 11
Notes: - 11 - Maximal Expandable Power Systems
PAGE 12
Notes: Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail: info@altronix.com, Lifetime Warranty, Made in U.S.A.