Installation Instructions

- 4 - NetWay1DWP/NetWay1DWPH/NetWay1DWPM/NetWay1DWPMH
2. Network Setup page will be displayed. You may now configure your NetWay1DWPM/H for network connection.
Fig. 5 -
NETWORK SETTING MENU.
This menu is for configuring the
NetWay1DWPM/H units for a
network connection.
Network Type:
Static IP
User can set a fixed IP for network connection.
DHCP
DHCP server in LAN will automatically an assign IP configuration for the network connection.
IP
This field shows the NetWay1DWPM/H current IP Address. A static IP address must be set manually.
If DHCP this value will be assigned automatically.
Subnet Mask
This field shows the subnet mask for your network so the NetWay1DWPM/H will be recognized within
the network. If DHCP is selected, this value will be assigned automatically.
Inbound Port
Port number for HTTP/WEB communication.
Host Name
Name of the NetWay1DWPM/H device on the LAN
Additional Information:
1. If using DHCP, all settings will be detected automatically.
While DHCP is a useful tool for determining the network settings, if you set up your NetWay1DWPM/H in this
manner, its IP address may change at different times for different reasons, particularly after a power failure.
If the IP address of the NetWay1DWPM/H changes, you may have difficulties accessing your NetWay1DWPM/H
locally and/or remotely.
It is strongly recommended that you connect via host name when units configured as DHCP.
Please do not set the DHCP address issued to the NetWay1DWPM/H by the router as its static IP address unless you
take specific steps that program your router to prevent such address conflicts.
2. If using a Static IP (recommended), you will need to input the information manually. In order for DDNS to work,
you must enter valid data compatible with your network for all of the network setting fields: IP address,
Subnet Mask, Gateway and Inbound Port.
3. If you are connecting through a router, make sure that you have ‘opened up’ all the required network ports in the port
forwarding section of your router’s setup options. That is, you have directed the router to send any incoming traffic
using those IP ports to the LAN IP address of the NetWay1DWPM/H. Useful information about router port
forwarding can be found at www.portforward.com. Different routers may use different terms for port forwarding
function. For instance, D-Link calls it virtual server, Netopia calls it pinholes.
The default port for NetWay1DWPM/H is: 80
Note: Port 80 is the default port used for web browsing. Because of this, in order to prevent the average user from
hosting a web server, most ISPs BLOCK traffic using port 80 from reaching the average site. If you only plan to
Management Interface
Version 0.88
Status
NetWay Network Settings
x
x
Setup Network Settings
192.168.168.168/networksetup.htm
®
NetWay1DWPM
Network Settings
Site ID: Altronix Site ID
Friday, May 16 2014 [11:11 am]
Reboot Server
Submit Network Settings
Submit Trap Receiver IP Settings
Submit Syslog Settings
Static
Network Settings: Trap Receiver Settings:
Syslog Settings:
192.168.168.168
255.255.255.0
192.168.168.100
80
10.10.10.53
10.10.10.76
10.10.10.12
10.10.10.13
10.10.10.14
10.10.10.15
100
IP Address Method:
IP Address:
Subnet Mask:
Gateway:
Inbound Port:
Syslog Server IP:
Syslog Server Port:
Trap Receiver Address 1:
Trap Receiver Address 2:
Trap Receiver Address 3:
Trap Receiver Address 4:
Trap Receiver Address 5: