Power over the Ethernet NetWay8G Eight (8) Port PoE Midspan Injector Installation Guide I.T.E. 43KC DOC#: NETG Rev. 092016 More than just power.
Table of Contents: Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview: Altronix NetWay8G is an 8-port networked Managed Midspan in a 1U rack enclosure. It provides PoE/PoE+ (up to 30W) power per port, and passes data at 10/100/1000 Mbps at distances up to 100m. Features also include an integral battery charger for applications requiring backup and embedded LINQ Technology to monitor, control, and report power and diagnostics from anywhere. Features: Agency Listings: • UL 60950-1 • CE Information Technology Equipment. European Conformity.
Fig. 2 - NetWay8G 2d NetWay8G - Front Panel 2a 2b 2e 2f 2c NetWay8G - Rear Panel 2g 2h OUT 1-8: Structured cable to PoE compliant cameras/edge devices. IN 1-8: Structured cable to ethernet switch or video server. LED(s) 1-8: Port status LEDs. Reset: Restores unit to factory settings. USB Port: For future use. Ethernet: For future use. IEC 320 Connector: 115/230VAC (grounded line cord included).
NetWay8G -5- Fig. 4 PoE Camera Transceiver Ethernet Switch NetWay8G - Front Panel Pace Long Range Ethernet Adapters Extends Ethernet approx. 500m PoE Camera Power OUT IN www.altronix.com I.T.E. 43KC Repeater NetwayXT Made in U.S.A.
Technical Specifications: Parameter No. of Ports Input Power Requirements Indicators Description Eight (8) PoE+ Ports (10/100/1000 Mbps). 115VAC, 60Hz, 3.25A or 230VAC, 50/60Hz, 2.0A. Port Status LEDs. Environmental Conditions Operating Ambient Temperature: Relative Humidity: Storage Temperature: Operating Altitude: – 20ºC to 40ºC (– 4ºF to 104ºF). 85%, +/– 5%. – 20ºC to 70ºC (– 4ºF to 158ºF). – 304.8 to 3,048m.
DHCP: A. After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings. A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK. Next, click on the button labeled Reboot Server. After rebooting the NetWay8G will be set in the DHCP mode. The IP address will be assigned by the router when the NetWay8G is connected to the network.
Rack Mount Installation Mounting Options: 1. Remove and discard factory installed screws from both sides of rack chassis (Fig. 5a). 2. Install mounting brackets (A) on the left and right side of rack chassis using the four (4) flat head screws (B) (included) (Fig. 5b). 3. Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 5c). Fig. 5 Fig. 5a Fig. 5b Top Fig. 5c Top Top Front Left Front Left Front Left B Remove A Wall Mount Installation 1.
