Installation Instructions

ManualsBrandsAltronix ManualsAccess Control Power products4-Door Access and Power Integration Kit - Trove1M1R with eFlow6NBV, ACM4CB, PDS8CB, VR6

Rev. T1RM3F4V080720

More than just power.

Installing Company: _______________ Service Rep. Name: __________________________________

Address: _____________________________________________ Phone #: __________________

Installation Guide

All registered trademarks are property of their respective owners.

T1RM3F4V

4 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix and Mercury backplane (TM1R)

- (1) eFlow6NBV - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8 - Fused Dual Output Power Distribution Module

- (1) ACM4 - Fused Access Power Controller

T1RM3F4DV

4 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove1R rack enclosure with Altronix and Mercury/LenelS2 backplane (TM1R)

- (1) eFlow6NBV - Power Supply/Charger

- (1) VR6 - Voltage Regulator

- (1) PDS8CB - PTC Dual Output Power Distribution Module

- (1) ACM4CB - PTC Access Power Controller

Access & Power Integration

Summary of content (8 pages)

PAGE 1
Access & Power Integration T1RM3F4V 4 Door Kit with Fused Outputs Fully assembled kit includes: - Trove1R rack enclosure with Altronix and Mercury backplane (TM1R) (1) eFlow6NBV - Power Supply/Charger (1) VR6 - Voltage Regulator (1) PDS8 - Fused Dual Output Power Distribution Module (1) ACM4 - Fused Access Power Controller T1RM3F4DV 4 Door Kit with PTC Outputs Fully assembled kit includes: - Trove1R rack enclosure with Altronix and Mercury/LenelS2 backplane (TM1R) (1) eFlow6NBV - Power Supply/Charger (
PAGE 2
Overview: Altronix T1RM3F4V and T1RM3F4DV rack kits are pre-assembled and consist of Trove1M1R enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies. These kits also accommodate various combinations of Mercury/LenelS2 boards for up to four (4) doors in a single enclosure. 2.5 ACM4CB Board Output PTC Rating 24VDC Output Range (V) 24VDC Output Range (V) Power Supply Board Battery Fuse Rating 5A/ 10A/ 20.28- 20.28250V 32V 26.4 26.4 24VDC @ 5.6A 2.5 10A/ 2.
PAGE 3
Installation Instructions for T1RM3F4(D)V: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. These products are for indoor use only and must be installed within the protected premises. Fig. 1 Note: First assemble and Install Z Bracket Wire Management Accesory Back of the drawer, (refer to Z Bracket Installation pg. 4) viewed from outside. 1.
PAGE 4
Assembling and Attaching Z Bracket Wire Management Accessory (included): Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory. Hardware (included): Ten (10) bolts and Fig. 3 eight (8) lock nuts. 1. Carefully unpack Z Bracket. Do not discard hardware (included) (Fig. 3, pg. 4). 2. Attach arms to each other using bolts and lock nuts (Fig. 3a, pg. 4). 3. Attach the hinge brackets to the ends of arms using bolts and nuts positioning them as shown on (Fig.
PAGE 5
T1RM3F4(D)V: Configuration of Mercury Boards: 1. Fasten spacers onto metal pems configuration (A), (B), (C) or (D) of backplane depending on the access controller (Fig. 5, pg. 5). 2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 5a, pg. 5). 3. Mount backplane to enclosure with hardware.
PAGE 6
Notes: -6- T1RM3F4(D)V Installation Guide
PAGE 7
Notes: T1RM3F4(D)V Installation Guide -7-
PAGE 8
Trove1R Enclosure Dimensions: 3.375” x 19.0” x 26.5” (85.8mm x 482.6mm x 673.1mm). Shown with Z Bracket attached. 0.1” 2.5mm 1.5” 38.1mm 11.175” (283.8mm) 1” (25.4mm) 2.4” 61mm 0.55” (14mm) 3.62” 92mm R 1.27” (32.3mm) 4.57” 116.1mm 26.5” 673.1mm 19” (482.6mm) 3.375” 85.8mm Altronix is not responsible for any typographical errors.